Reparationsassistent
Powered by ChatGPT
Reservedelsliste
3 GREASE FITTING, 1/4-28 STRAIGHT
Position: 1
2 BUMPER, RUBBER 5/16-18
Position: 1
2 GROMMET, 1-1/4
Position: 1
5 BUSHING-FUEL TANK RED RUBBER (SV)
Position: 1
20 WASHER, 5/16" SAE
Position: 1
1 SWITCH, BLADE ENGAGEMENT
Position: 1
12 WASHER, 5/16" SAE
Position: 1
2 CLUTCH ANCHOR PAD
Position: 1
1 NUT, 1/2-13 HEX JAM
Position: 1
1 CYL, HYD, 1.5 BORE X 5.5 STROKE
Position: 1
1 JOINT-BALL .500-20 THD .500ID BLK PLT
Position: 1
1 SCREW, #10-24 X 1 RS, CZ
Position: 1
1 GEARBOX, RIGHT ANGLE, 1:1
Position: 1
2 TIRE ASSY, 13 X 6.5 SILVER (Includes Ref No. 2 - 5 & 14)
Position: 1
1 DECAL, FERRIS, FRONT, 6.75 X 4.25
Position: 1
1 DECAL, FERRIS LOGO, MEDIUM
Position: 1
1 DECAL, MAIN SAFETY, ANSI CE
Position: 1
1 ROLLER, DECK
Position: 1
6 WASHER, 1/2 SAE
Position: 1
1 BELT, 5V, 197.90"EL, LRG ARAMID, WRP, RC
Position: 1
6 BODY CLIP, 5/16-18-7GA MATERIAL
Position: 1
1 BELT, 5V, 207.90"EL, LRG ARAMID, WRP, RC
Position: 1
1 CHUTE, DISCHARGE, RUBBER, 61/72, BENT (S/N: 2017118253 & Below)
Position: 1
4 BEARING, TAPERED ROLLER,
Position: 2
1 SPRING, COMP, .835 X.105 X4.26
Position: 2
2 PIN, Hitch, Black W/ Plastic Lanyard
Position: 2
1 STRAP-BLACK RUBB
Position: 2
2 VALVE, Fuel Shut Off
Position: 2
1 RING, SWITCH RETAINER
Position: 2
2 WASHER, 5/16" SAE
Position: 2
9 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 2
4 WASHER, FRAME RETAINING
Position: 2
1 PLUG, 1/2NPT, SQUARE HEAD
Position: 2
6 NUT, 1/2-13 HEX SIDE LOCK
Position: 2
1 WASHER, 5/8 SAE
Position: 2
1 SLEEVE, THRD 3/8-24
Position: 2
1 PULLEY, SPINDLE, BH72
Position: 2
2 TIRE, Front, 13 x 6.5 x
Position: 2
1 DECAL, FERRIS LOGO, 9-3/8
Position: 2
1 DECAL, FERRIS LOGO, XL
Position: 2
1 DECAL, MAIN SAFETY
Position: 2
2 GREASE FITTING, 1/4-28 STRAIGHT
Position: 2
19 WASHER, 5/16 SAE (Qty: 11 - Domestic Models)
Position: 2
1 FLAP, STRIPER, 61/72RD
Position: 2
2 SEAL, GREASE
Position: 3
1 WRENCH, SPANNER, CZ (NOT SHOWN)
Position: 3
1 WRENCH, SPANNER, CZ
Position: 3
2 RUBBER BUMPER
Position: 3
1 BATTERY, 12V (BCI58, 500 CCA)
Position: 3
11 CLAMP, #4 Hose
Position: 3
4 NUT, 5/16-18 HEX NYLOCK FLANGE
Position: 3
1 VOLTMETER, UNLIT, 12V, W/ COLOR GRAPHIC
Position: 3
6 NUT, 5/16-18 HEX NYLOCK FLANGE
Position: 3
4 NUT, M8-1.25 SERR. FLANGE, CZ (S/N: 2012609704 & BELOW)
Position: 3
1 FILTER HEAD
Position: 3
1 NUT, 5/8-11 HEX JAM NYLON LOCK
Position: 3
3 NUT, HEX 3/8-24
Position: 3
2 BUSHING, TAPERED HUB
Position: 3
1 DECAL, BADGE, IS5100, RH
Position: 3
1 DECAL, TANK, LRG, RH, FERRIS
Position: 3
2 DECAL, PRIMING INSTRUCTIONS
Position: 3
2 DECAL, PINCH POINT
Position: 3
2 PLUG, PANEL, 1.25 - BLACK
Position: 3
11 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 3
2 SPACER, .38 X .63 X 4.31
Position: 3
2 NUT, 1/2-13 HEX NYLON LOCK
Position: 3
2 WASHER, 1/2 USS
Position: 3
1 CHUTE, DISCHARGE, BEND RUBBER (SV) (S/N: 2017094785 & Below)
Position: 3
2 NUT, 3/4-16 HEX JAM
Position: 3
3 *PULLEY, FLAT IDLER, 6-3/4" *If not present, order 5025158 - washer and
Position: 3
4 BALL JOINT, 3/4-16, MALE
Position: 4
4 WASHER, 5/16" SAE
Position: 4
1 GAUGE, WATER TEMPERATURE
Position: 4
12 WASHER, 1/2" USS
Position: 4
4 SNAP RING, INTERNAL
Position: 4
10 NUT, 5/16-18 HEX NYLOCK FLANGE
Position: 4
2 CABLE, PARKING BRAKE
Position: 4
12 NUT, 1/2-13 HEX NYLOCK FLANGE GR8 YZ (Torque to 110 ft lbs)
Position: 4
1 RUBBER, FOOT PEDAL
Position: 4
1 ROD, LEVER CONNECTING, CZ
Position: 4
1 PULLEY, GEARBOX INPUT
Position: 4
1 DECAL, BADGE, IS5100, LH
Position: 4
1 DECAL, TANK, LRG, LH, FERRIS
Position: 4
1 DECAL, PARKING BRAKE SYMBOLS
Position: 4
2 DECAL, DANGER DO NOT OPERATE W/O DEFLECT
Position: 4
12 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 4
1 SPACER, .52 X 1.00 X 3.50
Position: 4
1 SPACER, .39 X .75 X .38
Position: 4
3 WASHER, 5/8 GRADE 8, YZ
Position: 4
1 ROD, MOUNT, CHUTE, 72, CZ (S/N: 2017118253 & Below)
Position: 4
2 COIL-OVER SHOCK ASSEMBLY
Position: 5
16 WASHER, 3/8 SAE
Position: 5
1 FITTING, TEE, 3/8" Hose
Position: 5
1 LATCH, CONTROL PANEL
Position: 5
9 WASHER, 3/8" SAE
Position: 5
4 WASHER 3/8" SAE
Position: 5
4 BEARING, BALL 11/16X1-9/16X15/32
Position: 5
4 BOLT, 3/8-16 X 1-1/4 SHCS
Position: 5
2 GROMMET, 1-1/4 (NOT SHOWN)
Position: 5
2 GROMMET, 1-1/4 (Not illustrated - Protects hoses routed through holes in frame.)
Position: 5
2 SPRING, BRAKE
Position: 5
4 WASHER, 1/2" SAE
Position: 5
5 GREASE FITTING, 1/4-28 STRAIGHT
Position: 5
1 DECAL, HEIGHT OF CUT, IS5000Z
Position: 5
1 DECAL, WARNING, HAND IN BELT, ENG ONLY (Located on pump plate.)
Position: 5
2 BUSHING, FLANGE
Position: 5
4 SEAL, 3/4 ROD END
Position: 5
1 EYE BOLT, 3/8-16 X 6, 3THRD, 1EYE, CZ
Position: 5
18 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 6
4 NUT, 5/16-18 NYLOCK FLANGE
Position: 6
1 LIGHT, GLOW PLUG, 22MM AMBER
Position: 6
1 SENDER, WATER, TEMPERATURE, 3/8 NPT (Not shown)
Position: 6
1 SPACER, .51 X 1.75 X.63
Position: 6
4 INSERT, BEARING
Position: 6
4 NUT, 3/8-16 HEX NYLON LOCK
Position: 6
2 WHEEL MOTOR-TF0405UB080AADD MB
Position: 6
1 WHEEL MOTOR, LH, TG0335UB080AAKZ
Position: 6
1 SPRING-EXT, .500 OD X 3.50 LG X .058 WR
Position: 6
1 SPRING-COMP, .615ID X 4.00LG X .080WR
Position: 6
1 BOLT, 1/2-13 X 7", CARRIAGE
Position: 6
4 ADAPTER, CASTER AXLE, CZ (S/N: 2016098450 & Below)(2 per tire)
Position: 6
2 DECAL, CAT DIESEL POWER
Position: 6
2 DECAL-OIL RESERVOIR
Position: 6
1 DECAL, MANUAL AVAIL IN SPANISH
Position: 6
1 COVER, VINYL HANDLE
Position: 6
1 IDLER ARM ASSEMBLY
Position: 6
2 BALL JOINT, 3/4-16, MALE
Position: 6
1 SPACER, .39 X 1.00 X .25
Position: 6
1 FLAP, STRIPER, 72 DECK
Position: 6
4 WASHER, 5/16 SAE
Position: 7
2 WASHER, 5/16 SAE
Position: 7
2 WASHER, 1/4" SAE
Position: 7
2 FITTING, 1/4" NPT, 90 Deg.
Position: 7
2 LIGHT, WARNING, 22MM RED
Position: 7
8 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 7
5 NUT, 5/16-18 HEX NYLOCK FLANGE
Position: 7
1 SPACER, .52 X 1.00 X 1.15
Position: 7
4 NUT, 5/16-18 HEX SERRATED FLANGE (LARGE)
Position: 7
1 OIL COOLER 1.5 X 8.5 X
Position: 7
1 KIT, AIR COOLER, IS5100Z
Position: 7
2 SPACER, .52 X 1.00 X 1.00
Position: 7
1 KNOB, PLASTIC, 1/2-13
Position: 7
1 BALL JOINT, 3/8-24 FEMALE
Position: 7
3 WASHER, FRAME RETAINING
Position: 7
1 DECAL, ICD CUTTING SYSTEM (MODELS WITH ICD MOWER DECKS ONLY)
Position: 7
1 WASHER,WAVE,M10
Position: 7
7 WASHER, 3/8 SAE
Position: 7
2 CLEVIS, 1/2-20, STEEL
Position: 7
5 NUT, 1/2-13 HEX NYLOCK FLANGE
Position: 7
2 WASHER, 3/4 SAE
Position: 7
4 SHIELD, PULLEY BEARING, CZ
Position: 7
6 WASHER, 3/8 SAE
Position: 7
4 NUT, 3/4-16 HEX JAM
Position: 8
2 SPACER, .38 X .50 X .75
Position: 8
3 WASHER, 3/8 SAE
Position: 8
1 FILTER/WATER SEPARATOR ASSEMBLY, Complete
Position: 8
1 POWER, OUTLET - 12 VOLT
Position: 8
6 WASHER, 3/8" SAE
Position: 8
1 SPRING-EXTN 1.040ODX 04.000LG .105WIRE D
Position: 8
5 WASHER, 1/2" SAE
Position: 8
1 CAP, 2-1/2 VENTED
Position: 8
4 SPACER, .52 X 1.00 X 1.15
Position: 8
9 BALL JOINT, 1/2-20, MALE
Position: 8
1 SPACER, .39 X 1.00 X .88, CZ
Position: 8
4 NUT, 1/2-13 HEX NYLON LOCK
Position: 8
2 NUT, 1/2-13 HEX NYLOCK FLANGE
Position: 8
1 DECAL, MODEL, IS5100Z
Position: 8
1 DECAL, BELT & BLADE, IS5100Z (Located Under Seat)
Position: 8
1 DECAL, CZT HYDRO RELEASE (Located under the seat plate.)
Position: 8
2 ROLLER, SMALL
Position: 8
2 BOLT, 1/2-20 X 2-1/2, FLT
Position: 8
2 NUT, 3/4-16 HEX NYLON LOCK
Position: 8
1 SPACER, .52 X 1.00 X .56, CZ
Position: 8
3 PULLEY, SPINDLE, BH72
Position: 8
4 WASHER, 3/8 SAE
Position: 9
2 SPRING, HOOD LATCH
Position: 9
1 WASHER, .39 X 2.00 X X .14
Position: 9
1 ROLL BAR HARDWARE BAG (Includes hitch pins)
Position: 9
12 WASHER, 5/16" LOCK
Position: 9
1 SPACER, .38 X .62 X 1.62
Position: 9
1 PULLEY, IDLER DOUBLE-A
Position: 9
8 NUT, 5/16-18 HEX SERRATED FLANGE (SMALL)
Position: 9
4 FITTING, #8 JIC - #8 O-RING, 90 DEG.
Position: 9
8 FITTING, #8 JIC - #8 O-RING, 90 DEG.
Position: 9
6 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 9
2 GREASE FITTING, 1/4-28 STRAIGHT (not shown)
Position: 9
10 BUSHING, 1.00 X 1.13 X 1.38, PLASTIC
Position: 9
1 WASHER, 3/8" FENDER
Position: 9
8 WASHER, 5/16" SAE
Position: 9
2 TIRE ASM, 26X12.00-12, 9.5 WIDE WHEEL
Position: 9
1 DECAL, WARNING, ROLL BAR, CE (Located On behind the ROPS on the frame
Position: 9
1 DECAL, WARNING OVERHANG, ROPS (SV)
Position: 9
4 *PULLEY, FLAT IDLER, 6-3/4" *If not present, order 5025158 - washer and
Position: 9
1 DECK SHELL W/DECALS, 61" iCD - IS5100 (S/N: 2016893014 & Below)
Position: 9
4 BUMPER, RUBBER, 5/16-18
Position: 10
8 NUT, 5/16-18 HEX NYLOCK FLANGE
Position: 10
9 NUT, 5/16-18 HEX NYLOCK FLANGE
Position: 10
1 SEAT BELT ASSEMBLY, Standard (Includes mounting hardware)
Position: 10
1 SEAT BELT ASSEMBLY, Extra Long (Includes mounting hardware)
Position: 10
2 WASHER, 5/16" LOCK
Position: 10
1 NUT, 1/2-13 HEX NYLON LOCK
Position: 10
1 NUT, 1/2-20 HEX NYLOCK
Position: 10
4 NUT, 3/8-24 HEX, LH
Position: 10
4 FITTING, #8 JIC - 1/2 NPT, STRAIGHT
Position: 10
1 PLATE, PIVOTER, IS5100Z
Position: 10
3 DECAL, CZT HYRDO RELEASE (Located Under Seat)
Position: 10
1 DECAL-OIL RESERVOIR (Located near hydraulic tank.)
Position: 10
2 HANGER, FRONT DECK - 4 LINK, 5.5" EB
Position: 10
1 IDLER MOUNT
Position: 10
21 NUT, 5/16-18 HEX NYLOCK FLANGE
Position: 10
4 NUT, 3/4-16 HEX NYLON LOCK
Position: 11
14 NUT, 5/16-18 HEX NYLOCK FLANGE
Position: 11
3 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 11
1 CAP, 2-1/2" VENTED
Position: 11
3 BOLT, M10-1.5 X 16MM GD8.8
Position: 11
2 BUSHING, FLANGE, 7/8" X 1" L
Position: 11
2 PULLEY, A SECTION, 4" IDLER
Position: 11
2 BEARING, FLANGE
Position: 11
2 FITTING T JIC #8
Position: 11
2 SPACER, .39 X 1.00 X .75
Position: 11
1 BUSHING, FLANGED, 3/8ID X 1/2OD, 5/8OD FLANGE
Position: 11
1 DECAL, SAFETY, CE ROPS
Position: 11
1 DECAL, BELT & BLADE, IS5100iCD, HYD LIFT (Located under the seat plate.)
Position: 11
4 BOLT, RD HD SH SQ NK 3/8- 16X1.000 G5 BL
Position: 11
2 BOLT, RD HD SH SQ NK 3/8- 16X1.000 G5 BL
Position: 11
21 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 11
3 PULLEY, FLAT IDLER, 6-3/4"
Position: 11
2 WELD, MOUNT, IDLER
Position: 11
4 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 12
1 SPACER, .38 X .50 X 5.06
Position: 12
4 SPACER, .38 X .50 X 1.00
Position: 12
3 CLAMP, Hose
Position: 12
1 HANDLE, THROTTLE CONTROL
Position: 12
2 BOLT, M10-1.5 X 30MM GD8.8
Position: 12
1 SLEEVE, A-ARM PIVOT - LONG
Position: 12
4 FITTING, #8 JIC - #10 O-RING, 45 DEG.
Position: 12
2 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 12
2 KEY, .250 SQ. X 1, ROUND END
Position: 12
10 BOLT, WHEEL LUG, 1/2" X 1-5/8
Position: 12
1 DECAL, SAFETY, CE ROPS, OBS
Position: 12
2 DECAL, WARNING, ROLL BAR (Located behind the ROPS on the frame of the
Position: 12
2 NUT, 1/2-13 HEX JAM
Position: 12
1 SPRING, EXT, 1.5ODX12.25X.234WIRE BLK
Position: 12
1 DECK SHELL W/DECALS, 61"RD - IS5100 (Export Models - S/N: 2016893014 &
Position: 12
1 SPACER, .52 X 2.00 X .88, CZ
Position: 12
2 NUT, 3/4-16, HEX JAM NYLON LOCK
Position: 13
1 SAFETY WALK, FLOOR PLATE, 17.13 X 11.50
Position: 13
1 SAFETY WALK, FLOOR PLATE, 16.00 X 10.00
Position: 13
4 NUT, 3/8-16 Hex Nylock Flange
Position: 13
4 WASHER, 3/8" USS
Position: 13
2 ELBOW FITTING
Position: 13
2 GAUGE, FUEL 12"
Position: 13
1 CABLE, THROTTLE CONTROL, 47.5 (NOT SHOWN)
Position: 13
1 WASHER, 1/2" SAE
Position: 13
1 BELT, 66.5" # 7-8672, SET
Position: 13
2 BALL JOINT, 3/8-24 MALE
Position: 13
1 PUMP, HYDROSTATIC - PW - 1ACC
Position: 13
2 SPACER, .38 X .50 X .27
Position: 13
4 SHIM, CAMBER - PLATED
Position: 13
1 CLEVIS, 3/8-24 RH, 3/8" PIN HOLE
Position: 13
2 WASHER, 1/2" SAE
Position: 13
1 DECAL, PINCH POINT, CE
Position: 13
2 BEARING, 3/4" FLANGED, BRONZE
Position: 13
1 EYE BOLT, 3/8-16 X 5, 1 EYE
Position: 13
1 ROD MOUNT, CHUTE 61"
Position: 13
8 BUSHING, .75 X 1.00 X 1.00, PLASTIC
Position: 13
1 IDLER MOUNT, .88 HIGH
Position: 13
12 SPACER, .39 X .75 X .50 (Export Models - S/N: 2016893014 & Below)
Position: 13
1 WASHER, .390 X 1.50 X .109, CZ
Position: 13
8 WASHER, 1/2 SAE
Position: 14
1 SAFETY WALK, FLOOR REST, 17.13 X 6.00
Position: 14
1 SAFETY WALK, FLOOR REST, 16.00 X 6.00
Position: 14
4 WASHER, 3/8" SAE
Position: 14
1 TANK, FUEL, DIESEL, RH
Position: 14
1 * SHAFT, STUB, FLYWHEEL PLATE
Position: 14
2 SPACER, .39 X 1.00 X .25
Position: 14
1 NUT, 3/8-16 SIDE LOCK
Position: 14
1 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 14
4 NUT, M8-1.25 NYLON LOCK, CZ
Position: 14
1 HYDRAULIC RESERVIOR
Position: 14
1 ROD, CRUISE CONTROL, SNP PRO WB
Position: 14
2 BEARING ADJUSTER, SPACER, 7.062LG (S/N: 2016098451 & Above)(1 per
Position: 14
1 DECAL, CE DANGER (Located on pump plate)
Position: 14
2 ROUND, PIN ANCHOR SHACKLE
Position: 14
2 SPACER, .52 X 1.00 X .44, CZ
Position: 14
2 SPACER, IDLER ARM, 1/2 X 2.25
Position: 14
1 PLUG, HOLE 2 1/8 (Export Models)
Position: 14
26 WASHER, 5/16 SAE
Position: 14
4 WASHER, BELLEVILLE - 1.500 X .755
Position: 15
8 NUT, 1/2-20 HEX NYLON LOCK
Position: 15
1 SEAT, 1110EVC, COMPANION (S/N: 2015478453 & Below)
Position: 15
1 SEAT, IS3100Z / IS5100Z (S/N: 2015478454 & Above)
Position: 15
2 SCREW, 1/2-13 X 1" SHCS
Position: 15
2 WASHER, 1/4 LOCK
Position: 15
1 5" AIR CLEANER ASSEMBLY (809670)
Position: 15
4 WASHER, .39 X 2.50 X .125
Position: 15
1 NUT, 3/8-16 HEX SERRATED FLANGE
Position: 15
2 HYDRALIC FITTING, MALE ELBOW
Position: 15
1 NUT, HEX 3/8-24 LH
Position: 15
2 NUT, BEARING ADJUSTER, AXLE (S/N: 2016098451 & Above)(1 per tire)
Position: 15
1 DECAL, FIRE ANSI EXPORT (Located near fuel cap)
Position: 15
1 DECAL, PRIMING INSTRUCTIONS
Position: 15
1 PIVOT, LINKAGE MOUNT WELDMENT - BLK
Position: 15
4 BUSHING, FLANGE
Position: 15
2 NUT, 1/2-20 HEX JAM
Position: 15
1 SPRING-EXT, 1.04 ODX10.535LGX.148WR, BLK
Position: 15
6 CLIP, BODY , 5/16-18 FOR 7 GA.
Position: 15
1 SPACER, .51 X .75 X 1.22, PM CZ
Position: 15
13 NUT, 5/16-18 HEX NYLOCK FLANGE (Qty: 5 - Domestic Models)
Position: 15
4 BEARING CUP
Position: 16
6 PLUG, PANEL, 1.25 - BLACK
Position: 16
1 KNOB-INT THR .312-18 4-ARM 2.12WD 1.06LG (USA Models)
Position: 16
2 NUT, 1/2-13 NYLOCK FLANGE
Position: 16
1 HOSE ASSEMBLY
Position: 16
1 TANK, FUEL, DIESEL, LH
Position: 16
1 HOSE, AIR FILTER IS5000
Position: 16
1 NUT, 3/8-16 HEX LG. SERR FLG
Position: 16
2 BOLT, 5/16-24 X 4.25" GD5 YZ
Position: 16
2 SHOCK, REAR, IS4500
Position: 16
6 NUT, 1/2-13 HEX NYLON LOCK
Position: 16
1 WELD, PEDAL LIFT, IS5100Z
Position: 16
9 NUT, 1/2-13 HEX NYLON LOCK
Position: 16
4 DEBRIS COVER, CASTER WHEELS (S/N: 2016098451 & Above)(2 per tire)
Position: 16
1 DECAL, WARNING, HOT (Located near radiator)
Position: 16
2 Washer, .390 X 1.50 X .109
Position: 16
2 CAPSCREW-HEX HD 7/16-14X2.000 G8 BLK
Position: 16
14 WASHER, 5/16 SAE
Position: 16
2 BEARING, 6203-1/2", SEALED
Position: 16
1 WASHER, 5/16 F436 FLAT
Position: 16
2 BOLT, 1/4-28 X 1/2, GD5 YZ
Position: 17
2 BOLT, 3/8-16 X 3/8, 1/2 SHOULDER
Position: 17
2 RUBBER WASHER
Position: 17
2 FUEL CAP, 3.5", NON VENTED, DIESEL (GRN)
Position: 17
1 MUFFLER, 3013C CAT DIESEL ENG
Position: 17
1 ISO-MOUNT, REAR
Position: 17
2 NUT, 3/8-16 NYLOCK FLANGE
Position: 17
1 SPACER, .52 X .99 X 2.55, SS
Position: 17
2 SPRING, REVERSE RETURN
Position: 17
1 GRIP, BLACK FLEXIBLE
Position: 17
2 SHOCK/SPRING ASSEMBLY, IS5000 (2006)
Position: 17
10 NUT, 1/2-20 HEX JAM
Position: 17
2 DECAL, DISCHARGE SAFETY, EXPORT
Position: 17
2 WASHER-0.437(0.47IDX0.94ODX.11THK) BLK
Position: 17
4 SHIELD, PULLEY BEARING
Position: 17
3 SPINDLE ASSM, CAST IRON - 10.0 (If replacing factory equipped spindle on
Position: 17
4 SPACER, .75 X 1.50 X 1.00, CZ
Position: 18
1 BOLT/WASHER ASM HOOD LATCH
Position: 18
4 MNT, VBRTN, RBBR
Position: 18
1 SWITCH, TOGGLE (S/N: 2016098450 & Below)
Position: 18
1 SCREEN, FRONT,RAD, IS5000Z-DSL
Position: 18
1 GREASE FITTING, 1/4-28, 90 DEGREE
Position: 18
2 BUSHING, BRASS, 1.25X1X1.25
Position: 18
2 BALL STUD 10MM 5/16-18 X 3/4" (S/N: 2012609705 & ABOVE)
Position: 18
10 NUT, 3/8-16 HEX NYLON LOCK
Position: 18
1 NUT, 3/8-16 HEX SIDE LOCK
Position: 18
5 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 18
6 3/8 PUSHNUT BOLT RETAINER
Position: 18
2 NUT-HEX FLANGE 7/16-14 TWO WAY LK GA BLK
Position: 18
1 FLAP, STRIPER, 61, RD
Position: 18
2 CAP, LOW PROFILE, STEEL
Position: 19
8 SCREW, Allen Head, #10-24 x 3/8"
Position: 19
1 WASHER, .50 X 1.75 X .13
Position: 19
2 NUT, 5/16-24 HEX NYLON LOCK
Position: 19
12 WASHER, 3/8 SAE
Position: 19
1 BALL JOINT, 3/8-24 LH FEMALE
Position: 19
5 WASHER, 3/8 SAE
Position: 19
2 Grease Fitting, 1/4-28 Straight
Position: 19
3 WELD, MOUNT, IDLER
Position: 19
1 SAFETY WALK, IS5000 A-ARM STEP
Position: 20
1 HOOD LATCH, IS5000
Position: 20
2 VENT TUBE, DIESEL
Position: 20
2 ISO-MOUNT, ENGINE
Position: 20
1 CLUTCH WARNER,1-1/4"GT300IXR-0
Position: 20
2 NUT, 5/16-24 HEX
Position: 20
1 PUMP, DECK LIFT, PW-1DCC-QY1X-XXXX
Position: 20
1 SWITCH, DP NO/NC SNAP-IN
Position: 20
1 WASHER, 1/2 SAE
Position: 20
1 SPACER, .39 X .75 X .580
Position: 20
3 WASHER, 1/2 SAE
Position: 20
2 PIN-ROUND HD DRILLED .375 X 1.500 BLK
Position: 20
3 PULLEY, SPINDLE, BH66
Position: 20
3 WASHER, 5/8" GRADE 8, YZ
Position: 20
4 WASHER, 1/2 USS
Position: 20
1 WASHER, 5/16 FENDER (Export Models)
Position: 20
1 KIT, FUEL TANK VENT LINE (Includes Ref Nos 1, 3, 11 - 13 & 20)
Position: 21
8 WASHER, 5/16" LOCK
Position: 21
3 WASHER, .34 X 1.25 X10 GA
Position: 21
1 SPACER, .52 X 1.00 X .75
Position: 21
2 CLEVIS, 5/16-24, STEEL
Position: 21
1 VALVE, HYD, 2 POS, 3 WAY
Position: 21
1 VALVE, HYD, 4 WAY, 2 POSITION
Position: 21
1 VALVE. HYD, MECH, IS5100 DECK LIFT
Position: 21
2 HUB, BRAKE (S/N: 2000786068 & BELOW)
Position: 21
4 WASHER, 1/2 GD9 YZ
Position: 21
1 NUT, 5/16-18 HEX NYLOCK FLANGE
Position: 21
3 KEY 1/4 SQ X 1 1/2 LONG
Position: 21
1 WASHER-3/8 FENDER
Position: 21
1 SPRING, TORSION (Export Models)
Position: 21
8 WASHER, 1/4 SAE
Position: 22
4 CLIP, BODY 5/16-18
Position: 22
1 SWITCH-IGNITION (COMPLETE)
Position: 22
4 BOLT, 5/16-18 X 1/2" FLANGE, SPEC
Position: 22
1 FITTING, TEE, #6 ORING TO #6JIC, MALE
Position: 22
1 HOSE ASSEMBLY (20.5) LP, ST & ST END
Position: 22
10 WASHER, 3/8" SAE
Position: 22
12 NUT, 1/2-20 HEX NYLON LOCK
Position: 22
5 BOLT, 3/8-16 X 3/4, PLT W/PATCH
Position: 22
2 WASHER, 3/8 GD.9 FLAT
Position: 22
3 BUSHING, TAPERED HUB
Position: 22
1 DECK SHELL W/ DECALS, 61RD, IS5100Z DOM (Domestic Models)
Position: 22
24 WASHER, 5/16 SAE (Qty: 26 - S/N: 2017394311 & Below)
Position: 22
1 CAP, PROTECTOR, .120 ID (Export Models)
Position: 22
1 HOSE, UPPER RADIATOR CAT
Position: 23
1 MOUNT,ISO,TOP,RAD 5000Z-DIESEL
Position: 23
1 SPACER, .515 X 1.875 X .375 (S/N: 2013262992 & Above)
Position: 23
1 FITTING, STR, 1/4NPT MALE - #6JIC SWIVEL
Position: 23
2 NUT, 5/16-18 HEX SERRATED FLANGE (SMALL)
Position: 23
4 SPACER, .51 X .75 X .56, CZ
Position: 23
2 WASHER 3/8" SAE
Position: 23
1 PULLEY, DEEP V-IDLER, 6.25"OD S 1/2" ID
Position: 23
1 DECK SHELL W/ DECALS, 61RD, 5100, CE (Export Models - S/N:
Position: 23
16 WASHER, 5/16 SAE
Position: 24
1 ACORN NUT, 5/16-18 S/S (CE Export Models)
Position: 24
1 HOSE, LOWER RADIATOR - CAT
Position: 24
1 BOLT, CRANKSHAFT, 1/2-20 X 1-3/4" GD8 YZ (S/N: 2013262992 & Above)
Position: 24
2 PULLEY, Pump Drive
Position: 24
1 FITTING, 90DEG, #6 JIC TO #6 ORING MALE
Position: 24
3 FITTING, 90DEG, #6 JIC TO #6 ORING MALE
Position: 24
4 FITTING, 90DEG, #6 JIC TO #6 ORING MALE
Position: 24
2 NUT, 3/8-16 HEX SERRATED FLANGE
Position: 24
2 SPACER, .52 X 1.00 X .38
Position: 24
1 FLAP, STRIPER, 61 DECK, IS3100 S200X
Position: 24
18 NUT, 5/16-18 HEX NYLOCK FLANGE (Qty: 22 - S/N: 2017394311 & Below)
Position: 24
2 BUMPER, RUBBER 1/4-20 (72" Models - S/N: 2016893015 & Above)
Position: 25
4 NUT, 3/8-16 HEX NYLOCK FLANGE (S/N: 2013952543 & Above)
Position: 25
1 BOOT COVER, TOGGLE SWITCH (S/N: 2016098450 & Below)
Position: 25
1 PRESSURE CAP
Position: 25
2 MOUNT, ISO, BOTTOM, RAD 5000Z-DIESEL
Position: 25
1 BELT, HA X 36.6, SET
Position: 25
1 SPRING, EXTENSION, SWIVEL END
Position: 25
2 BEARING, BRONZE FLANGE, 3/4
Position: 25
1 HOSE, ASM, 41.5", IS5100 DECK LIFT
Position: 25
1 HOSE, ASM, 36", IS5100 DECK LIFT
Position: 25
16 BELLEVILLE WASHER 1.259 X .512 X .138 YZ
Position: 25
1 WASHER, 5/16" SAE
Position: 25
1 PULLEY, DEEP V-IDLER, 6.25"OD X 1/2"ID
Position: 25
4 NUT, 1/2-13 HEX NYLOCK FLANGE
Position: 25
1 NUT, 3/8-16 HEX JAM
Position: 25
1 DECK SHELL W/ DECALS, 72RD, 5100, DOM (USA Models - S/N:
Position: 25
2 NUT, 1/4-20 HEX NYLOCK FLANGE (72" Models - S/N: 2016893015 & Above)
Position: 26
4 WASHER, 3/8 SAE (S/N: 2013952543 & Above)
Position: 26
1 PETCOCK VALVE
Position: 26
1 PULLEY, PUMP DRIVE (S/N: 2016098450 & Below)
Position: 26
2 NUT, 1/4-20 HEX NYLOCK FLANGE
Position: 26
1 HOSE ASM, 28", IS5100 DECK LIFT
Position: 26
1 HOSE ASM, IS5100 DECK LIFT
Position: 26
1 SPACER, .52 X 1.00 X .63, CZ
Position: 26
1 SPACER, .52 X 1.00 X .750
Position: 26
1 DECK SHELL W/ DECALS, 72RD, 5100, CE (Export Models - S/N:
Position: 26
2 NUT, 1/4-20 HEX NYLON LOCK
Position: 27
4 BOLT, M8 X 25MM
Position: 27
5 BOLT, 5/16-18 X 1/2" FLANGE, SPEC
Position: 27
1 ANCHOR, CLUTCH
Position: 27
1 KEY, 5/16" SQ RD ENDS, 1.46 LG Was 5050404X4
Position: 27
1 BREATHER VENT, 1/4" NPT
Position: 27
2 NUT, 1/4-20 HEX SIDE LOCK
Position: 27
2 ROD, DECK LIFT INNER
Position: 27
1 PIN, HAIR, .0915 X 1-7/8
Position: 27
1 SAFETY WALK, 4.00 X 7.50
Position: 27
1 NUT, 3/8-16 HEX
Position: 27
1 NUT, 1/2-13 HEX SIDE LOCK
Position: 27
1 SAFETY WALK, 4.00 X 7.50 (Not Shown)
Position: 27
4 NUT, 5/16-18 HEX NYLOCK FLANGE (72" Models - S/N: 2016893015 & Above)
Position: 28
1 SHROUD, RUBBER IS5100Z was
Position: 28
5 WASHER, 1/4 SAE
Position: 28
1 BRACKET, AIR CLEANER ASSY -
Position: 28
2 KEY, 5MM SQ. W/ RADIUS
Position: 28
1 FITTING, STR, #6 ORING MALE - 1/4NPT FEM
Position: 28
2 CALIPER, MECHANICAL (S/N: 2000786068 & BELOW)
Position: 28
2 ROD, DECK LIFT OUTER
Position: 28
1 DECK SHELL W/ DECALS, 61, 5100, ANSI-EXP (ANSI-EXP Models - S/N:
Position: 28
4 WASHER, 5/16 SAE (72" Models - S/N: 2016893015 & Above)
Position: 29
1 WASHER, .34 X 1.25 X 10 GA
Position: 29
5 NUT, 1/4-20 HEX NYLOCK FLANGE
Position: 29
1 AIR FILTER ELEMENT (SECONDARY)
Position: 29
1 ** SHROUD, RADIATOR, 5000Z-DIESEL (S/N: 2015214824 & Below)
Position: 29
1 BOLT, CRANKSHAFT, 7/16 X 1-1/2" (S/N: 2013262991 & Below)
Position: 29
2 BUSHING, 17MM, HQ
Position: 29
2 DAMPENER (S/N: 2012609704 & BELOW)
Position: 29
1 NEEDLE VALVE, 1/4" NPT
Position: 29
2 SPACER, .52 X 1.00 X 1.15
Position: 29
1 NUT, #10-24 HEX NYLON LOCK
Position: 29
1 SPACER, .52 X 1.75 X .63, CZ
Position: 29
12 BOLT, M14-1.5 X 25MM
Position: 30
1 SPACER, .45 X 1.88 X .38 (S/N: 2013262991 & Below)
Position: 30
2 BALL STUD 10MM 5/16-18 X 1/2" (S/N: 2012609705 & ABOVE)
Position: 30
2 FITTING, STR, #6JIC TO #4 ORING, MALE
Position: 30
4 NUT, 1/2-13 HEX JAM
Position: 30
5 WASHER, .390 X 1.50 X .109, YZ
Position: 30
1 AIR FILTER ELEMENT (PRIMARY)
Position: 31
2 WASHER, LOCK, 10MM
Position: 31
2 PAD, RUBBER
Position: 31
4 BOLT, M8-1.25 X 35MM, GD8.8 (S/N: 2012609704 & BELOW)
Position: 31
1 FITTING, PLUG, #6 ORING
Position: 31
2 BALL JOINT 5/16-24 RH FEMALE BRONZE RACE
Position: 31
4 PIVOT BLOCK, PLASTIC
Position: 31
10 BODY CLIP, 5/16-18-7GA MATERIAL
Position: 32
1 CAP, A/C RAIN
Position: 32
2 WASHER, .41 X 1.75 X .14
Position: 32
3 ASSM, PULLEY IDLER (Includes Ref Nos 4-6 & 11)
Position: 32
2 GRIP, FOAM, 3/4" ID, 16" LONG
Position: 32
2 FITTING, 90DEG, #6 JIC MALE-#6JIC SWIVEL
Position: 32
2 SPRING, COMPRESSION
Position: 32
1 SPACER, .56 X .90 X .31
Position: 32
1 CHUTE, RUBBER DISCHARGE (5104442) (S/N: 2017094786 & Above)
Position: 32
11 WASHER, 5/16" GD.9 FLAT
Position: 33
1 SEAL, RADIATOR LOWER
Position: 33
2 SET SCREW, 5/16-18 X 3/8, KNURL, W/PATCH
Position: 33
1 FITTING, #6JIC-#6 ORING, STR. MALE-MALE
Position: 33
3 FITTING, #6JIC-#6 ORING, STR. MALE-MALE
Position: 33
2 FITTING, #6 jic-#8 O-RING, STRAIGHT
Position: 33
1 SPACER, .64 X 1.00 X .50, CZ
Position: 33
1 PIN, LATCH, SPR LOADED-PULL ACT
Position: 34
2 WASHER, 3/8" GD.9 FLAT
Position: 34
1 PULLEY, 5.75" OD X 1.375" BORE, DOUBLE A (S/N: 2016098451 & Above)
Position: 34
1 FITTING,90 ELBOW, #6JIC-1/4NPT MALE-MALE
Position: 34
1 HOSE ASSEMBLY (62) LP, ST & 45 ENDS
Position: 34
2 CLAMP, 5/16, DOUBLE, WIRE & TUBE
Position: 35
2 CLAMP, SS HOSE 2-3/4"
Position: 35
1 HOSE ASSEMBLY (9) LP, ST & 45 ENDS
Position: 35
1 * DECK SHELL W/ DECALS, 72, 5100, DOM (Domestic Models - S/N:
Position: 35
1 HOSE ASSEMBLY (16.5) LP, ST & ST ENDS
Position: 36
1 * DECK SHELL W/ DECALS, 72, 5100, CE (Export Models - S/N: 2016893015 &
Position: 36
2 NUT, 1/4-20 HEX SERR. FLANGE
Position: 37
1 TIE WRAP, 24" LONG (Not Shown)
Position: 37
2 ROD END, 3/8-24 LH FEMALE
Position: 37
1 HOSE ASSEMBLY (64) LP, 45 & 45 ENDS
Position: 37
1 HOSE ASSEMBLY (62) LP, 45 & 45 ENDS
Position: 37
2 COMPACT CALIPER, AUSCO (86978) (S/N: 2000786069 & ABOVE)
Position: 37
1 CLAMP, BARREL, THROTTLE (Not shown - Throttle parts on engine)
Position: 38
2 WASHER, .390 X 1.50 X .109, YZ
Position: 38
2 ARM, PUMP CONTROL (21 SERIES)
Position: 38
1 HOSE ASSEMBLY (64) LP, ST & 45 ENDS
Position: 38
1 WHEEL MOTOR, RH, TG0335UB081AAKZ
Position: 38
2 WHEEL HUB, COMPACT CALIPER (86720) (S/N: 2000786069 & ABOVE)
Position: 38
1 CLAMP, CONDUIT (Not shown - Throttle parts on engine)
Position: 39
2 LINK, ADJUSTABLE, SHORT
Position: 39
1 HOSE ASSEMBLY (21.5) LP, ST & 90 ENDS
Position: 39
2 HOSE ASSEMBLY (28), STR & 45 ENDS (S/N: 2016803539 & Above)
Position: 39
4 NUT, 1/2-13 HEX NYLON LOCK
Position: 39
2 SPACER, .39 X .75 X .38
Position: 40
1 HOSE ASSEMBLY (24.5) LP, ST & 45 ENDS
Position: 40
2 HOSE ASSEMBLY (26), STR & 45 ENDS (S/N: 2016803539 & Above)
Position: 40
1 WELD, LIFT ASSIST, IS5100Z
Position: 40
2 WASHER, 1/4" LOCK (Not shown - Throttle parts on engine)
Position: 41
1 HOSE ASSEMBLY (15) LP, ST & ST ENDS
Position: 41
1 WELD, DECK LIFT SHAFT, IS5100
Position: 41
1 NUT, #10-24 HEX NYLON LOCK (Not shown - Throttle parts on engine)
Position: 42
1 WASHER, M10, INTERNAL TOOTH LOCK, SS (S/N: 2016607952 & Below)
Position: 42
1 HOSE ASSEMBLY (7) LP, 4 ST & 45 ENDS
Position: 42
2 SPACER, .52 X 1.00 X .38, CZ
Position: 43
1 NUT, M6-1.0 (Not shown - For Alternator)
Position: 43
1 BOLT, M10-1.5 X 16MM GD8.8 (S/N: 2016607952 & Below)
Position: 43
1 HOSE ASSEMBLY (36.5) LP, ST & ST ENDS
Position: 43
2 LINK, DECK LIFT
Position: 43
1 NUT, 1/2-20 HEX NYLON LOCK
Position: 43
1 CHUTE, RUBBER DISCHARGE (S/N: 2017118254 & Above)
Position: 43
1 SOC SET SCREW, M10-1.5 X 50, SS, CAP PT (S/N: 2016607953 & Above)
Position: 44
2 SWITCH, PLUNGER, N.O.
Position: 44
1 ROD, MOUNT, CHUTE 61, CZ (S/N: 2017118254 & Above)
Position: 44
1 NUT, M10-1.5, NYLON INSERT (S/N: 2016607953 & Above)
Position: 45
1 PIN-CLEVIS, 1/2 X 2-1/2 YZP
Position: 45
1 HEX NUT, FLG, M10-1.5 SER CZ, NO SEALER (S/N: 2016607953 & Above)
Position: 46
4 NUT, #10-24 HEX NYLON LOCK
Position: 46
2 NUT, 3/8-24 HEX
Position: 47
1 GROMMET, 3/4
Position: 48
2 SPACER, .38 X .50 X 1.00
Position: 49
2 WASHER, 5/16" USS
Position: 49
1 SPRING-EXT, 1.393 ODX13.25LGX.218WR, BLK
Position: 49
1 BUSHING, DECK PIVOT
Position: 50
2 DAMPENER, CONTROL (S/N: 2012609705 & ABOVE)
Position: 53
2 NUT, 3/8-16 HEX
Position: 53
1 DZUS, RETAINER, PUSH-ON, SS
Position: 55
1 EYE BOLT, 3/8-16 X 8, 1 EYE
Position: 55
1 EYE BOLT, 3/8-16 X 6, 1 EYE
Position: 55
1 DZUS, RECEPTACLE, CLIP-ON, D8
Position: 56
1 DZUS, 1/4 TURN FASTENER, D8X16MM
Position: 57
1 DZUS, CUPPED WASHER
Position: 58
1 DZUS, EJECTOR SPRING
Position: 59
8 NUT, 1/4-20 HEX NYLOCK FLANGE
Position: 60
2 NUT, 3/8-16 HEX NYLON LOCK
Position: 60
2 NUT, #10-24 HEX NYLON LOCK
Position: 62
2 WASHER, #10 SAE
Position: 63
1 FOAM, SOUND BAFFLE, LH
Position: 66
1 SWITCH, OIL PRESSURE (Not shown)
Position: 66
1 FOAM, SOUND SHIELD, RH
Position: 67
1 SWITCH, WATER TEMPERATURE - NET (Not shown)
Position: 67
1 FOAM, SOUND SHIELD
Position: 68
1 FOAM, HOOD, SOUND SHIELD, LH
Position: 69
1 FOAM, HOOD, SOUND SHIELD, RH
Position: 70
1 FOAM, HOOD, SOUND SHIELD (S/N: 2016098450 & Below)
Position: 71
1 NUT, 5/16-18 HEX SERRATED FLANGE (LARGE)
Position: 76
1 SCREEN, SPARK ARRESTER (Not shown)
Position: 78
1 FOAM, HOOD, SOUND SHIELD (S/N: 2016098451 & Above)
Position: 79
1 SOLENOID, FUEL, 2 - POST (Not shown)
Position: 80
1 CLAMP (Not Shown - Holds lower radiator hose #24)
Position: 81
Aubière Cedex
Position: 63178
IS5100Z Series w/ Caterpillar Diesel & ROPS Export (IS5100ZC33D ANSI)
Position: 5900507
72" Side Discharge iCD Mower Deck (5100/72)
Position: 5900591
72" Rear Discharge iCD Mower Deck (5100/72RD)
Position: 5900592
IS5100Z Series w/ Caterpillar Diesel, 61" iCD Mower Deck & ROPS Export (IS5100Z/C
Position: 5900979
IS5100Z Series w/ Caterpillar Diesel & ROPS Export (IS5100ZC33DCE)
Position: 5900995
IS5100Z Series w/ Caterpillar Diesel, 61" RD iCD Mower Deck & ROPS Export (IS5100
Position: 5900996
61" Rear Discharge iCD Mower Deck - Export (5100/61RDCE)
Position: 5900997
72" Rear Discharge iCD Mower Deck Export (5100/72RDCE)
Position: 5900998
72" iCD Mower Deck - Export (5100/72CE)
Position: 5901010
IS5100Z Series w/ Caterpillar Diesel & ROPS (IS5100ZC33D)
Position: 5901011
IS5100Z Series w/ Caterpillar Diesel, 61" iCD Mower Deck & ROPS (IS5100ZC33D61)
Position: 5901013
IS5100Z Series w/ Caterpillar Diesel, 72" iCD Mower Deck & ROPS (IS5100ZC33D72)
Position: 5901282
IS5100Z Series w/ Caterpillar Diesel, 72" RD Mower Deck & ROPS (IS5100ZC33D72R
Position: 5901283