Eksploderet visning HOMELITE Homelite CS 40 and CS 50
Oplev den komplette eksploderede visning HOMELITE Homelite CS 40 and CS 50 – en uundværlig guide til at identificere reservedele. Vores præsentation hjælper dig med at forstå hver komponent i. Find hurtigt delene til din HOMELITE Homelite CS 40 and CS 50.
Reparationsassistent
Powered by ChatGPT
Reservedelsliste
3 SCREW- Thread Form (8-16 x 1 3/4")
Position: 1
1 OIL TANK ASSY
Position: 1
1 HANDLE BAR
Position: 1
4 SCREW-Thread Form (8-16 x 5/8")
Position: 1
SCREW- Thread Form. (8-16 x 5/8")
Position: 2
4 SCREW-PAN Hd. (10-24 x .800)
Position: 2
1 VALVE-Check
Position: 2
1 VALVE- Check
Position: 2
7 SCREW, Thread Form (8-16 X 5/8")
Position: 2
1 SCREW-Thread Form (8-16 x 2")
Position: 2
1 PIN-Spirol
Position: 3
1 HANDLE-Rear
Position: 3
1 SCREW-Thread Form. (10-14 x 1 1/8")
Position: 4
1 TUBING- Rubber (7 1/4")
Position: 4
1 SPRING-Compression
Position: 4
1 ROPE, STARTER (46")
Position: 4
1 WASHER-Lock
Position: 5
1 FILTER- Oil
Position: 5
1 RING, Retaining
Position: 5
1 GRIP, STARTER
Position: 5
1 SPRING & CONTAINER
Position: 6
2 BOLT Guide Bar
Position: 7
1 SCREW- Square Hd. (10-32 x 2 1/2)
Position: 8
2 RING, WRIST PIN RETAIN,
Position: 8
1 FILTER- Oil Tank Valve
Position: 8
1 WASHER
Position: 8
2 SCREW- Square Hd. (10-32 x 2 1/4)
Position: 9
2 SCREW-Hex Hd. (12-24 x 1")
Position: 9
2 BEARING, BALL
Position: 9
1 FUEL TANK ASSY
Position: 9
1 PIN-Dowel
Position: 9
1 SCREW Plastite (10-14 x 5/8")
Position: 9
1 SCREEN-Spark Arrestor
Position: 10
1 STOP- Chain
Position: 10
1 BEARING, NEEDLE
Position: 10
1 TUBING-Rubber (5 1/4")
Position: 10
1 SCREW- Thread Form (10-14 x 7/8")
Position: 11
1 TUBING- Rubber (9")
Position: 11
1 SPRING-Trottle
Position: 11
1 WASHER LOCK (3/8")
Position: 11
3 NUT Locking (10-32)
Position: 12
1 PLATE- Guide Bar (Outer)
Position: 12
4 SCREW, Hex Hd. (12-24 X 7/8")
Position: 12
1 FILTER- Foam
Position: 12
1 WASHER- Flat (#12)
Position: 13
1 SCREW- Thread Form. (6-19 x 1/2")
Position: 13
1 KEY WOODRUFF
Position: 13
1 FILTER- Fuel
Position: 13
1 MOUNTING BRACKET Handguard
Position: 13
2 SCREW, Sems Hex Hd. (10-24 x 7/8")
Position: 13
1 SPACER-Carburetor Includes items 15-16
Position: 14
1 PLATE- Guide Bar (Inner)
Position: 14
1 RETAINING RING
Position: 14
2 SAWDUST SEAL
Position: 14
1 NUT-Flange Hex
Position: 14
1 PIN- Adjusting
Position: 15
2 SCREW, FIL. HD. (8-32 X 5/8")
Position: 15
2 SCREW, Thread Form (#6-19 X 7/8")
Position: 15
1 SLEEVE, Insulating
Position: 15
1 FOAM- Adhesive
Position: 16
1 SCREW- Guide Bar Adjusting
Position: 16
2 SPRING-Extension
Position: 16
1 IGNITION MADULE
Position: 16
1 CARBURETOR W/AIR FILTER (Walbro) Includes items
Position: 17
1 WASHER, THRUST
Position: 17
1 RING- Snap
Position: 17
1 TUBING, OIL (TO GUIDE BAR)
Position: 17
1 SPRING-Extension
Position: 17
1 SPARK PLUG BOOT KIT
Position: 17
1 NUT, HEX LOCK (3/8"-24)
Position: 18
1 BULB- Primer
Position: 18
1 WORM GEAR, LEFT HAND
Position: 18
3 RETAINER-Spring
Position: 18
1 GASKET Carburetor
Position: 19
1 ROD- Choke
Position: 19
1 SEAL, CRANKSHAFT
Position: 19
1 WASHER-Flat (#10)
Position: 19
1 SWITCH
Position: 19
1 RETAINER PLATE
Position: 20
1 SWITCH- Ign.
Position: 20
1 SLEEVE-Spring
Position: 20
2 RETAINER NUT Filter
Position: 21
2 NUT, HEX
Position: 21
1 BOOT Throttle Cable
Position: 21
1 NUT-Square (#10-24)
Position: 21
2 "O" RING
Position: 22
1 GROMMET Choke
Position: 22
1 SCREW-Pan Hd. (#10-24 X 7/8")
Position: 22
1 PANEL Control
Position: 23
2 WASHER-Flat
Position: 23
2 NUT Hex (8-32)
Position: 24
2 SCREW-Thread Form (8-16 X 1/2)
Position: 24
2 SCREW Mach. Hex Hd. (8-32 x 7/8")
Position: 25
1 NUT, HEX LOCK (3.8"-24)
Position: 25
1 PIN-Throttle Lock
Position: 25
1 SCREW Thread Form (6-19 x 5/8")
Position: 26
1 WASHER, THRUST
Position: 26
1 LABEL Warning
Position: 26
1 WASHER Flat (#6)
Position: 27
1 RACE, INNER
Position: 27
1 GROMMET Carburetor
Position: 27
1 TUBING-Rubber (9")
Position: 28
1 BEARING, NEEDLE
Position: 28
1 DECAL-Kickback
Position: 28
1 TUBING- Rubber (4 3/4")
Position: 29
3 SCREW- Round Hd. (10-24 x .710)
Position: 30
1 CLUTCH ASSY
Position: 31
3 NUT Square (10-24)
Position: 31
1 COVER-Snap On
Position: 31
1 SPRING, CLUTCH
Position: 32
1 PIN-Cotter
Position: 32
1 GUIDE BAR FASTENER KIT
Position: 33
2 NUT Hex (5/16"-18)
Position: 33
1 DECAL, SAFETY
Position: 34
1 ISOLATOR KIT Includes items 16-21
Position: 07214
1 HANDLE KIT Includes items 1-24
Position: 07217