Exploderad vy Fischer elt2246k46
Upptäck den fullständiga exploderade vyn Fischer elt2246k46 – en oumbärlig guide för att identifiera reservdelar. Vår presentation hjälper dig förstå varje komponent i din . Hitta snabbt delarna till din Fischer elt2246k46.
Reparationsassistent
Powered by ChatGPT
Lista över reservdelar
2 WHEEL & TIRE ASSEMBLY, Front
Position: 1
1 SEAT, Low Back (Used on 2690577 only)
Position: 1
1 SEAT, Hi Back, Steel Pan
Position: 1
1 CAP, Steering Wheel, Plain
Position: 1
1 PAD, Foot Pedal Reverse
Position: 1
1 CAPSCREW, Hex Head, Taptite, 5/16-18 x 3/4
Position: 1
*TRANSMISSION, Tuff Torq K46BP
Position: 1
* TRANSMISSION, Tuff Torq K46BL
Position: 1
1 DECAL, Height Of Cut
Position: 1
2 NUT, Push, 3/8
Position: 1
2 BOLT, Rear Wheel (42" Only)
Position: 1
3 NUT, Hex, Flange, 9/16-8
Position: 1
2 NUT, Hex Flange Center Locking, 3/8-16
Position: 1
1 CLIP, Pin, Safety
Position: 1
3 NUT, Hex Flange 9/16-18
Position: 1
1 DECAL, Snapper, LH Hood Stripe
Position: 1
1 DECAL, Snapper, LH Hood Stripe (Model 2690841 Only)
Position: 1
1 SWITCH ASSEMBLY, Ignition, 6-Pole (Includes Ref. 2, 3, 4 & 5)
Position: 1
1 TIRE, Turf 15 X 6.00 - 6 Saver TL
Position: 2
12 CAPSCREW, Whizlock, 1/4-20 x 5/8
Position: 2
4 WASHER, Plain, 5/16
Position: 2
1 NUT, Hex Lock, ESNA Light, 5/8-18, Thin
Position: 2
1 VALVE, Shut Off Oil Drain
Position: 2
1 CARRIAGE BOLT, 1/4-20 x 5/8 G5
Position: 2
1 ROD, Deflector
Position: 2
1 CAPSCREW, Hex Washer Head, Taptite, 3/8-16 x
Position: 2
2 WASHER, 1/2 (42" Only)
Position: 2
6 WASHER, Belleville
Position: 2
2 WASHER, Plain, 13/32 x 1-1/2 x 1/8
Position: 2
3 PULLEY
Position: 2
1 DECAL, Snapper, RH Hood Stripe
Position: 2
1 DECAL, Snapper, RH Hood Stripe (Model 2690841 Only)
Position: 2
1 WASHER, 5/8
Position: 2
1 TUBE, Tire, Front
Position: 3
1 DUCT, Air Inlet Plastic
Position: 3
1 LATCH, Seat 20GA E-Coat
Position: 3
1 WASHER, 5/8
Position: 3
2 SPACER, Pivot Powdered Metal
Position: 3
1 SEAL, Short
Position: 3
1 SEAL, Long (B&S Single)
Position: 3
1 ROD, Bypass, 11.44 LG Yellow
Position: 3
6 BOLT, Carriage, 5/16-18 x 3/4
Position: 3
1 WASHER, Plain, 13/32 x 1-1/2 x 1/8
Position: 3
2 WHEEL, Gauge (42" Only)
Position: 3
3 PULLEY, RH Arbor & LH Arbor, 4-1/4
Position: 3
1 HUB
Position: 3
1 DECAL, Ignition Switch Symbol, White/Black
Position: 3
1 LOCKWASHER, Internal Tooth, 5/8
Position: 3
1 WHEEL & BUSHINGS ASSEMBLY, Front
Position: 4
1 SCREW, Pan Head #10-24 x 1/2
Position: 4
4 CAPSCREW, Hex Head Flange Dog Point, 5/16-18 x
Position: 4
1 STEERING WHEEL, w/Aluminum Insert
Position: 4
2 PIN, Quick
Position: 4
1 NUT, Hex Flange Whiz, 1/4-20
Position: 4
11 NUT, Hex, Flange Whizlock, 5/16-18 (38" Only)
Position: 4
13 NUT, Hex, Flange Whizlock, 5/16-18 (42" Only)
Position: 4
2 HUB, Pulley, RH (Middle)
Position: 4
1 SPACER
Position: 4
2 SPACER
Position: 4
1 DECAL, Steering Wheel Icon
Position: 4
1 DECAL, Steering Wheel Icon (Model 2690841 Only)
Position: 4
1 NUT, Hex, Flange, 5/8-32
Position: 4
4 BEARING
Position: 5
2 PUSH NUT
Position: 5
4 SPACER, Powdered Metal Yellow
Position: 5
1 RING, Klipring Extension
Position: 5
4 SCREW, Hex Washer Head Taptite 5/16-18 x 5/8
Position: 5
1 NUT, Hex Flange, 5/16-18 ESNA
Position: 5
1 GRIP
Position: 5
1 SPRING, Torsion
Position: 5
1 SPACER, 0.387 ID x 1-1/2 OD x 1.04 LG Powdered Metal
Position: 5
2 NUT, Hex Flange, 5/16-18
Position: 5
3 SPACER
Position: 5
1 CAPSCREW, Hex Head, 3/8-16 x 2-1/2
Position: 5
1 PIN, Hitch
Position: 5
6 BEARING, Ball 11/16 x 9/16 x 15/32
Position: 5
1 DECAL, Height of Cut Not Used on 40" Mower
Position: 5
1 COVER, Ignition
Position: 5
1 FITTING, Grease, 1/4-28 Thread
Position: 6
1 KNOB, Cruise Lock Green Plastic
Position: 6
2 WASHER
Position: 6
6 NUT, Hex, Flange Whizlock, 5/16-18
Position: 6
1 ROD, Lift Handle E-Coat, 17.7 LG
Position: 6
6 NUT, Hex, Flange Whizlock, 5/16-18
Position: 6
1 CAPSCREW, Hex Head, 3/8-16 x 2-1/4
Position: 6
2 NUT, Hex Flange, 3/8-16 ESNA (42" Only)
Position: 6
1 CAPSCREW, Dog Point, SEMS, 1/4-20 x 3/4
Position: 6
1 ROD, Bail Mowers Yellow
Position: 6
3 SPACER, Powdered Metal
Position: 6
1 DECAL, Snapper Rear Stripe, Silver/ 8.5LG
Position: 6
1 DECAL, Snapper Rear (Model 2690841 Only)
Position: 6
1 IGNITION KEY (Set of 2)
Position: 6
2 VALVE STEM & CAP
Position: 7
1 COVER, Steering Shaft Plastic
Position: 7
2 BOLT, Carriage, 5/16-18 x 3/4
Position: 7
2 BUSHING, Steering
Position: 7
1 MUFFLER (B&S Twin)
Position: 7
VENT VALVE
Position: 7
1 DEFLECTOR & SUPPORT ASSEMBLY, Chute Riveted
Position: 7
4 WASHER, 3/8
Position: 7
11 BOLT, Carriage, 5/16-18 x 3/4 (38" Only)
Position: 7
13 BOLT, Carriage, 5/16-18 x 3/4 (42" Only)
Position: 7
1 CAPSCREW, Hex Head, 1/4-20 x 1/2
Position: 7
6 BEARING
Position: 7
1 PULLEY ASSEMBLY
Position: 7
3 GASKET
Position: 7
1 DECAL, Transmission Tow/ Release Lever
Position: 7
1 SWITCH, Headlights, 2 Terminal
Position: 7
8 WASHER, 3/4
Position: 8
4 WASHER, Flat, 3/4 x 1-1/4 (Model 2690841 & 2690865 Only)
Position: 8
2 CAPSCREW, Hex Head, Taptite, 5/16-18 x 3/4
Position: 8
1 ROD, Cruise Latch, 16.97LG
Position: 8
1 TRANSMISSION ASSEMBLY, K46BP
Position: 8
1 TRANSMISSION ASSEMBLY, K46BL (Used with 22" Tire Models)
Position: 8
MAGNET
Position: 8
1 WASHER, Plain, 21/64 x 1-1/4
Position: 8
2 IDLER, Flat
Position: 8
2 NUT, Hex Lock ESNA, 1/4-20
Position: 8
3 GASKET, Foam
Position: 8
1 SPACER
Position: 8
1 DECAL, Fuel Level
Position: 8
1 PLUG, Hole, Square
Position: 8
4 WASHER, Special Yellow
Position: 9
2 WASHER, Plain, 5/16
Position: 9
4 BOLT, Carriage, 5/16-18 x 3/4
Position: 9
2 CLIP, Linkage, Black
Position: 9
1 PIPE, Exhaust R.H. (B&S Twin)
Position: 9
4 SCREW, Hex Head Flange Lock, 5/16-18 x 2-1/2
Position: 9
1 SPRING, Torsion, 2.12 LG Black
Position: 9
2 PULLEY, 5.25 (38" Only)
Position: 9
2 PULLEY, 5.50 (42" Only)
Position: 9
2 PULLEY, 7.00 (42" Only) (CE/Export)
Position: 9
2 NUT, Hex, Flange Whizlock, 5/16-18
Position: 9
1 WASHER, 1/4
Position: 9
1 NUT, Whizlock, 3/8-16
Position: 9
2 CAPSCREW, Hex Head, Flange Whiz Lock, 5/16-18 x 3/4
Position: 9
26 SCREW, Hex Washer Head Taptite 5/16-18 x 3/4
Position: 9
1 DECAL, Tunnel
Position: 9
1 DECAL, Safety Instructions (CE/Export)
Position: 9
1 DECAL, Tunnel (France Models Only)
Position: 9
1 DECAL, Safety Instructions (Used only on ACS models)(CE/Export)
Position: 9
1 PLUG, Hour Meter (Kohler and B&S Single)
Position: 9
4 RING, Retaining
Position: 10
4 RING, Retaining, 3/4 (Model 2690841 & 2690865 Only)
Position: 10
1 KNOB, Brake Lock Plastic
Position: 10
4 NUT, Hex Flange, 5/16-18 ESNA
Position: 10
1 ROD, Parking Brake, 16.38 LG Yellow
Position: 10
1 PIPE, Exhaust L.H. (B&S Twin)
Position: 10
1 CAPSCREW, Hex Head, 3/8-16 X 1-3/4
Position: 10
2 CAPSCREW, Hex, 5/16-18 x 3/4
Position: 10
1 SPRING, Extension, Idler Arm (44” Mower Deck)
Position: 10
1 SPRING, Extension, Idler Arm (50” Mower Deck)
Position: 10
4 NUT, Hex Flange, 3/8-16 ESNA
Position: 10
1 DECAL, Belts,Blades (France Models Only)
Position: 10
1 DECAL, Belts, Blades
Position: 10
1 METER, Hour, LCD (B&S V-Twin Only)
Position: 10
4 CAP, Hub
Position: 11
4 CAP, Hub (Model 2690841 & 2690865 Only)
Position: 11
1 DASHBOARD
Position: 11
2 BOLT, Shoulder 5/16-18 G5
Position: 11
2 BOLT, Carriage, 3/8-16 x 1-1/4
Position: 11
1 SPACER
Position: 11
1 SPACER, Pivot Powdered Metal
Position: 11
2 BEARING, Upper
Position: 11
4 CAPSCREW, Hex Head, Flange Whiz Lock, 5/16-18 x 3/4
Position: 11
1 HUB, Adapter, LH
Position: 11
1 V BELT, Arbor Drive, 44”
Position: 11
1 V BELT, Arbor Drive, 44” (CE Only)
Position: 11
1 V-BELT, Arbor Drive, 50”
Position: 11
1 V-BELT, Arbor Drive, 50” Deck, 126.14" LG HA used on
Position: 11
4 WASHER, 1/2
Position: 11
1 WASHER, Plain, 1/4 (6 Total for Export)
Position: 11
2 KEY, 3/16 x 3/16 x
Position: 12
1 KEY, 3/16 x 3/16 x 2 (Model 2690841 & 2690865 Only)
Position: 12
1 GUIDE, Hood RH
Position: 12
2 SPRING, Compression
Position: 12
1 MUFFLER
Position: 12
1 V-BELT, Drive Belt, Aramid/Kevlar 89.25" EL HA
Position: 12
BYPASS SHAFT A
Position: 12
3 NUT, Hex, Flange Whizlock, 5/16-18
Position: 12
2 NUT, Hex Lock, ESNA Light, 5/8-18, Thin
Position: 12
2 NUT, Whizlock, 3/8-16
Position: 12
1 CAPSCREW, Hex Head, 3/8-16 x 1-1/4, G8
Position: 12
4 WHEEL, Gauge
Position: 12
2 CARRIAGE BOLT, 5/16-18 x 3/4 G5
Position: 12
1 DECAL, LT200 18.5HP
Position: 12
1 DECAL, LT200 20HP
Position: 12
1 DECAL, LT200 22HP
Position: 12
1 NUT, Wing, 1/4-20
Position: 12
2 WASHER
Position: 13
2 WASHER
Position: 13
4 WASHER, Spring Black
Position: 13
1 SPRING, Extension 07.52 LG Black
Position: 13
1 PIPE, Exhaust (B&S Single)
Position: 13
LEVER, Bypass
Position: 13
2 SPACER, Pulley, 38" Deck
Position: 13
1 SPRING, Extension 07.75 LG Black
Position: 13
1 PIN, Hitch
Position: 13
29 CAPSCREW, Hex Head, Taptite, 5/16-18 x 3/4
Position: 13
4 BOLT, Rear Wheel
Position: 13
1 DECAL, Danger, Chute in Place Not Used on 40" Mower
Position: 13
1 CARRIAGE BOLT, 1/4-20 x 7/8
Position: 13
2 SPACER, 0.77 ID x 1-1/4 OD x 1.65 LG Powdered Metal Black
Position: 14
2 RIVET, Pop, Stem Black
Position: 14
2 COVER, Spring
Position: 14
1 PULLEY, 3 OD Plastic
Position: 14
4 SCREW, Hex Washer Head Taptite 1/4-20 x 1/2
Position: 14
1 WASHER, Flat, 5/16
Position: 14
RING, Snap,
Position: 14
2 SCREW, Taptite, 5/16-18 x 5/8
Position: 14
2 RETAINING RING, Extension, 1-3/4
Position: 14
1 NUT, 3/8-16, Hex Flange MAC Locking Large, Black
Position: 14
2 SPACER, .532 ID x 3/4 OD x 1-1/4 LG Yellow
Position: 14
3 WASHER
Position: 14
3 NUT, Hex Flange 5/16-18, Whiz Lock Small
Position: 14
1 DECAL, Pinch Point Not Used on 40" Mower
Position: 14
1 NUT, Push On
Position: 14
2 WHEEL & TIRE ASSEMBLY, Rear 20"
Position: 15
2 WHEEL & TIRE ASSEMBLY, Rear 22"
Position: 15
1 GUIDE, Hood LH
Position: 15
1 POD, LH Cup Holder
Position: 15
1 SHAFT, Steering Gear & Spline Yellow
Position: 15
2 NUT, Hex Flange, 3/8-16 ESNA
Position: 15
1 CLIP, Speed Wire
Position: 15
1 CAPSCREW, Hex Head, 5/16-18 x
Position: 15
SEALING CAP
Position: 15
4 CLIP, Spring
Position: 15
10 SCREW, Hex, Washer Head, Taptite, 3/8-16 x 3/4
Position: 15
2 BOLT, Carriage, 5/16-18 x 3/4
Position: 15
2 NUT, ESNA, Lock, 1/2-13 (Thin)
Position: 15
1 SHAFT, Arbor
Position: 15
3 WASHER, Cup
Position: 15
1 DECAL, Danger, Hand Under Deck Not Used on 40" Mower
Position: 15
1 HOLD DOWN, Battery
Position: 15
1 TIRE, Turf 20 X 8.00 - 8 Saver TL
Position: 16
1 TIRE, Turf 22 X 10.00 - 8 Saver TL
Position: 16
12 NUT, Hex Flange Whiz, 1/4-20
Position: 16
1 ELBOW FITTING
Position: 16
1 BOLT, Carriage, 5/16-18 x
Position: 16
1 CONTROL, Throttle Double (B&S Single)
Position: 16
1 CONTROL, Throttle Double (B&S Twin)
Position: 16
1 CONTROL, Throttle, Choke-A-Matic (Models 2690841 & 2690865 only)
Position: 16
RING, Snap, C
Position: 16
2 WASHER, 1/2
Position: 16
1 V-BELT, 91.10 LG Kevlar (Used on 38" Domestic Models)
Position: 16
1 V-BELT, 94.45 LG Kevlar (Used on 42" Domestic Models)
Position: 16
1 V-BELT, 91.10 LG A-Wedge Aramid (Used on 38" CE/Export Models)
Position: 16
1 V-BELT, 94.45 LG A-Wedge Aramid (Used on 42" CE/Export Models)
Position: 16
1 CLIP, Pin, Safety
Position: 16
3 SHIELD, Grass, Lower
Position: 16
1 SWITCH, Push Button (NC)
Position: 16
1 TUBE, Tire, Rear, 22 X 8 -
Position: 17
1 TUBE, Tire, Rear, 22 X 10 -
Position: 17
1 BUSHING
Position: 17
4 CAPSCREW, Hex Washer Head, Taptite, 5/6-18 x 5/8
Position: 17
1 PULLEY, Idler
Position: 17
2 CLAMP, Hose
Position: 17
1 WASHER, Plain, 5/16
Position: 17
SEAL WASHER
Position: 17
2 PIN, Threaded Shoulder
Position: 17
1 HOUSING, 42" (42" Only)
Position: 17
1 HOUSING, 38" (38" Only)
Position: 17
3 BLADE, 44”
Position: 17
3 SHIELD, Grass Lower Arbor, Heat Treated
Position: 17
1 DECAL, 38"
Position: 17
1 DECAL, 42"
Position: 17
1 DECAL, 44"
Position: 17
1 DECAL, 50"
Position: 17
3 TIE, Self Locking 7-5/16
Position: 17
1 WHEEL, Hub
Position: 18
1 ROD, Dash Support
Position: 18
1 TANK, Fuel
Position: 18
1 SPRING, Extension
Position: 18
1 HOSE, Fuel
Position: 18
1 CAPSCREW, Hex Head, 5/16-18 x 1-3/4
Position: 18
1 FITTING, Grease
Position: 18
1 ROD, Bail Mowers Yellow
Position: 18
3 WASHER, Hex
Position: 18
3 BLADE, Mower
Position: 18
1 DECAL, Hand Under Deck (CE/Export)
Position: 18
1 OUTLET, 12 Volt DC Power
Position: 18
4 WASHER, 3/4 x 1-7/8 (Model 2690841 & 2690865 Only)
Position: 19
1 SCREW, Taptite, 1/4-20 x 1/2
Position: 19
1 CAP, Gas
Position: 19
1 PIN, Cotter 3/32 x 3/4
Position: 19
2 CLIP, Hose
Position: 19
8 NUT, Hex, Flange Whizlock, 5/16-18
Position: 19
0-RING, 1A P10A
Position: 19
2 NUT, Hex, Flange, Whizlock, 5/16-18 x 1/2
Position: 19
1 SHAFT, Spindle, 38" Deck
Position: 19
3 WASHER, Spring
Position: 19
3 WASHER, Hex 11/16 x
Position: 19
1 PLUG, Hole Models W/O 12V Adapter
Position: 19
1 NUT, Hex, Nylon, Lock, #10-24
Position: 20
1 PAD, Footrest LH
Position: 20
1 ROD, Brake, 15.1 LG
Position: 20
3 SCREW, Hex Washer Head Taptite 3/8-16 x 1 (B&S Single)
Position: 20
SEAL TC
Position: 20
2 DECAL, CAUTION! Pinch Point
Position: 20
3 CAPSCREW, Hex Head, 7/16-14 x 1-1/4
Position: 20
1 SWITCH, Push Button (NO/NC)
Position: 20
4 NUT, Hex, Flange Whizlock, 5/16-18
Position: 21
1 SPRING, Extension 05.37 LG Black
Position: 21
1 LOCKWASHER, External Tooth 3/8
Position: 21
2 BOLT, Shoulder
Position: 21
4 WASHER, Belleville
Position: 21
2 BOLT, Carriage, 5/16-18 x 3/4
Position: 21
8 BOLT, Carriage, 5/16-18 x 3/4 (CE Only)
Position: 21
3 CAPSCREW, Hex Head 7/16-14 x 1-1/4 G8
Position: 21
1 PAD, Footrest RH
Position: 22
1 PEDAL, Brake Rubber
Position: 22
1 WASHER, 3/8
Position: 22
SCREW, Tapping, 8 *
Position: 22
2 NUT, Hex 9/16-18
Position: 22
2 SHAFT, Arbor
Position: 22
4 SCREW, Taptite, 5/16-18 x 5/8
Position: 22
1 PIN, Quick
Position: 23
2 SPACER (Used on 38" & 42" Mower Decks)
Position: 23
2 SPACER (Used on 44" & 50" Mower Decks)
Position: 23
2 BLADE, Mower 38" (38" Only)
Position: 23
2 NUT, Hex, Flange Whizlock, 5/16-18
Position: 23
8 NUT, Hex, Flange Whizlock, 5/16-18
Position: 23
1 CARRIAGE BOLT, 1/4-20 x 1 G5
Position: 23
1 HEADLIGHT ASSEMBLY (Includes Ref. 24, 25, 26 & 27)
Position: 23
1 INSERT, Lightbar
Position: 24
6 SCREW, Hex, Washer Head, Plastite, 1/4-20 x 1/2
Position: 24
1 ROD, Brake Return, 12.60 LG
Position: 24
1 PULLEY & HUB ASSEMBLY, Engine
Position: 24
2 TRUNNION, Powdered Metal
Position: 24
2 WASHER, Spindle Blade Powdered Metal
Position: 24
1 COVER, Arbor
Position: 24
2 SOCKET ASSEMBLY
Position: 24
1 HEADLIGHT ASSEMBLY
Position: 25
6 SCREW, Taptite, 5/16-18 x 5/8
Position: 25
1 TIE, Self Locking
Position: 25
PIN, 3 * 9.8
Position: 25
PIN 3 * 9.8
Position: 25
2 ROD, Lower Life, 10.00 LG
Position: 25
2 NUT, Push for 1/4 Diameter Thread
Position: 25
2 BULB, 1141-12V 21CP
Position: 25
1 POD, RH Lift Quadrant
Position: 26
1 ROD, Cruise Latch, 2.83 LG
Position: 26
1 RETAINER, Clutch
Position: 26
2 SHAFT, Arbor, RH
Position: 26
4 WASHER, 1/4
Position: 26
1 REFLECTOR, Headlight
Position: 26
1 SPRING, Tension, Clutch
Position: 27
BOLT, 10 *
Position: 27
1 ROD, Lift, 5.43 LG
Position: 27
6 SCREW, Tapitite 1/4-20 x 1/2 (38" Only) (CE/Export)
Position: 27
2 CARRIAGE BOLT, 1/4-20 x 1, Black
Position: 27
1 CLAMP, Wire
Position: 27
1 LENS, Headlight
Position: 27
1 LATCH, Cruise Powdered Metal
Position: 28
1 CLUTCH, Electric OGURA
Position: 28
1 SPRING, Extension 5.10 LG Black (Used on 44" & 50" Mower Decks)
Position: 28
1 COVER, Arbor, RH
Position: 28
1 WASHER, 5/16
Position: 28
1 BOLT, Shoulder 5/16-18 G5
Position: 29
1 WASHER, Hex
Position: 29
IDS SPRING
Position: 29
2 NUT, Push On
Position: 29
1 SPRING, Torsion, Chute
Position: 29
1 NUT, Hex, Flange, 1/4-20
Position: 29
1 LOCKWASHER, Spring
Position: 30
4 LOCKWASHER, Interior Tooth 5/8 (42" Only) (CE/Export)
Position: 30
2 WASHER, Plain, 1/4 (6 Total for Export)
Position: 30
2 NUT, Hex Lock ESNA Light 1/4-20
Position: 30
1 COVER, Terminal
Position: 30
1 CAPSCREW, Hex Head 7/16-20 x 3-1/2 G5
Position: 31
1 CLAMP
Position: 31
1 DEFLECTOR
Position: 31
1 HARNESS, Wiring (Use on models with 12 Volt Outlet)
Position: 31
1 HARNESS, Wiring (Use on models without 12 Volt Outlet)
Position: 31
1 GASKET, Exhaust
Position: 32
SPRING
Position: 32
2 NUT, Hex Lock, ESNA, 1/4-20
Position: 32
1 ROD, Deflector
Position: 32
1 CABLE, Solenoid to Starter
Position: 32
2 SCREW, Hex Washer Head Taptite 3/8-16 x 1-1/4 (Qty. 1 used on 18.5HP)
Position: 33
PUMP SHAFT
Position: 33
PUMP SHAFT
Position: 33
1 WASHER, Flat, 5/16
Position: 33
2 HUB
Position: 33
1 SOLENOID
Position: 33
2 CAPSCREW, Hex Socket Head 5/16-18 x 3/4 G8
Position: 34
E-RING
Position: 34
7 RIVET, Pop (38" - France Only)
Position: 34
1 DEFLECTOR, Plastic
Position: 34
1 PLUG
Position: 34
2 SCREW, Taptite, 1/4-20 x 1/2
Position: 34
2 LOCKWASHER, Spring 5/16
Position: 35
BEARING, 6202C3
Position: 35
1 SPRING
Position: 35
2 LOCKWASHER, External Tooth, 5/16
Position: 35
MOTOR HOUSING
Position: 36
6 WASHER, Bellville
Position: 36
2 NUT, Hex, 5/16-24 NF
Position: 36
1 PAD, Foot Pedal Forward
Position: 37
2 PIVOT, Hood
Position: 37
1 SCREW, Hex Head Serange Flange Taptite 5/16-18 x
Position: 37
1 CABLE, #6 x 10 Long, with 2 Ring Terminals, Battery to Solenoid
Position: 37
2 BOLT, Carriage, 5/16-18 x
Position: 38
KIT, Cylinder Block
Position: 38
1 PLUG, Plastic (Not Shown)
Position: 38
1 CARRIAGE BOLT, 1/4-20 x 1-1/2 G5
Position: 38
2 NUT, Hex Flange Whizlock, 5/16-18
Position: 39
WASHER, 12 * 24 *
Position: 39
MOTOR SHAFT
Position: 40
2 CARRIAGE BOLT, 5/16-18 x 3/4
Position: 40
RING, Snap, S15
Position: 41
1 BOOT, Insulator
Position: 41
BRAKE DISC/MOTOR GEAR (11T)
Position: 42
BRAKE DISC/MOTOR GEAR (10T)
Position: 42
1 BATTERY, 12 Volt, 230CCA
Position: 42
1 BATTERY, 12 Volt, 230CCA (CE/Export)
Position: 42
1 SWITCH, Push Button (NO), Reverse Pedal
Position: 43
THRUST METAL
Position: 44
2 NUT, Hex, Full, 1/4-20
Position: 44
2 LOCKWASHER, 1/4
Position: 45
THRUST BEARING K81105
Position: 46
2 WASHER, 1/4 I.D.
Position: 46
1 CABLE, Battery to Ground
Position: 47
2 CAPSCREW, Hex Head, 1/4-20 x 3/4
Position: 48
1 FUSE, Wiring Harness
Position: 49
1 NO-MOW MODULE
Position: 50
1 KEY, w/Hang Tag for RMO Module
Position: 51
1 SWITCH, PTO, Push/Pull Symbols
Position: 52
CONTROL LEVER C
Position: 53
WASHER,
Position: 55
COTTER PIN, 1/8 * 3/4
Position: 56
SPRING PIN 6 *
Position: 57
ROLL PIN 6 *
Position: 58
O-RING 1A P14
Position: 59
NUT
Position: 60
WASHER, 12 * 32 * 3.2
Position: 65
REDUCTION GEAR (38T)
Position: 66
AXLE SHAFT, Left
Position: 68
AXLE SHAFT, Right
Position: 69
THRUST WASHER
Position: 70
RING
Position: 71
SEAL 19 * 32 *
Position: 72
BUSHING, 19 *
Position: 73
BRAKE SHOE
Position: 75
BRAKE LEVER
Position: 76
BRAKE ACTUATOR
Position: 79
SPRING PIN 5 *
Position: 80
O-RING 1A P12
Position: 81
SPRING PIN 4 *
Position: 82
PULLEY D
Position: 84
FAN, White
Position: 85
WASHER, Wave
Position: 86
SNAP RING
Position: 87
RING, Snap
Position: 87
OIL SEAL 16 * 22 * .03
Position: 91
K46 & T40 SEAL KIT (ALL MODELS)
Position: 200