Eksploderet visning e 281123 bve SNAPPER e281123bve
Oplev den komplette eksploderede visning e 281123 bve SNAPPER e281123bve – en uundværlig guide til at identificere reservedele. Vores præsentation hjælper dig med at forstå hver komponent i din e 281123 bve. Find hurtigt delene til din e 281123 bve SNAPPER e281123bve.
Reparationsassistent
Powered by ChatGPT
Reservedelsliste
2 ASSEMBLY, Front Tire & Rim (Complete) (Includes Items 2A, 3A, 4, 5 & 6)
Position: 1
2 ASSEMBLY, Rear Tire & Rim (33” Models) (Includes 2A, 3A & 4)
Position: 1
1 ASSEMBLY, Steering Wheel (for 5/8” shaft) Includes item
Position: 1
1 WELDMENT, Main Case (Standard)
Position: 1
1 COLLAR, Lock (Includes P/N 90201 Set Screw)
Position: 1
1 ASSEMBLY, Primary Chain Case Includes Items 2 thru 13, 15,
Position: 1
1 ASSEMBLY, Smooth Clutch (Incl. items 2 thru 6) Non-Asbestos
Position: 1
1 SEAT, Operator (shown) used on 13HP & Higher Models
Position: 1
1 MUFFLER w/Heat Shield (Briggs 11 & 13HP)
Position: 1
1 WELDMENT, 5.25” O.D. Drive Disc used on 33” Deck Models
Position: 1
1 CONTROL, Throttle (23.6” long) (Briggs Engines)
Position: 1
1 COVER, Spindle
Position: 1
1 FOOT PEDAL, Blade Stop Control
Position: 1
1 BELT, Drive (73.75” AA Section) used on 33” Deck Models
Position: 1
1 ASSEMBLY, Spindle Housing (Incl. items 2 thru 13)
Position: 1
1 DECAL, Brake Operation (German)
Position: 1
1 KIT, 12 Volt Dry Charge Battery
Position: 1
1 LOGO, Steering Wheel
Position: 2
1 BALL BEARING, Axle (R.H. Fender) used on 33” Models- 13, 14 &
Position: 2
1 WELDMENT, Primary Chain Case, Right Hand
Position: 2
1 ASSEMBLY, Driven Disc Hub Was
Position: 2
1 ASSEMBLY, Fuel Tank (Includes item 3) used on 9 & 10HP Models
Position: 2
2 SCREW, 1/4-20 x 5/8” Hex Washer Head Self-Tap Was
Position: 2
2 SET SCREW, HRSS, 3/8-16 x 3/8”
Position: 2
2 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap Was
Position: 2
1 DECK, 25” Replacement (Painted deck with decals)
Position: 2
1 SPRING, Latching
Position: 2
1 NUT, 3/4-16 Hex Jam, GR
Position: 2
2 RING, 1.85” Internal Retaining
Position: 2
1 DECAL, Brake Operation (French)
Position: 2
1 SOLENOID, Super-Trombetta replaces
Position: 2
1 SOLENOID, Super-Trombetta
Position: 2
1 PIN, 1/4 x 1-1/2" Roll
Position: 3
1 FENDER, Left Hand (Standard)
Position: 3
1 GASKET, Primary Chain Case
Position: 3
1 DISC, Driven (rubber tire bonded to rim)
Position: 3
1 CAP, Fuel Tank
Position: 3
2 SET SCREW, 5/16-18 x 3/4” Socket Head, GR8
Position: 3
1 KEY,1/4” Square x 2” Long
Position: 3
1 PLATE, Throttle Control
Position: 3
1 DEFLECTOR, Discharge (Incl. items 4, 5, 6, 7 & 10) used on 25” Deck Models
Position: 3
2 ADJUSTER, Chain (5/16-18 thread)
Position: 3
1 SPRING, Pedal
Position: 3
2 WASHER, 49/64” I.D. x 1-1/2” O.D. Flat
Position: 3
2 BEARING, Spindle
Position: 3
1 DECAL, Brake Operation (Dutch)
Position: 3
1 HARNESS, Starter Wiring (Briggs Engines)
Position: 3
1 HARNESS, Starter Wiring (Briggs, AC)
Position: 3
1 HARNESS, Starter Wiring (Kohler Engines)
Position: 3
2 BALL BEARING, Flange (3/4” I.D.) per front tire ass'y.
Position: 4
1 VALVE STEM, Snap In (per rear tire ass'y)
Position: 4
1 LATCH, Parking Brake
Position: 4
1 WASHER, Thrust
Position: 4
2 WASHER, 5/8” Belleville
Position: 4
1 THRUST WASHER
Position: 4
1 HOSE, Fuel (1/4” I.D. x 8-1/2” long) used on Briggs 8-14HP
Position: 4
1 MUFFLER (Kohler 14 & 15HP)
Position: 4
1 DECAL, Danger, (Cut Finger) International Symbol
Position: 4
2 NUT, 5/16-24 Hex Was
Position: 4
1 SHOULDER BOLT, 3/8-24 w/Nylon Patch, GR5
Position: 4
1 PULLEY, Deck
Position: 4
1 WELDMENT, Spindle Housing Was
Position: 4
1 HARNESS, Ignition Wiring (Briggs Engines)
Position: 4
1 HARNESS, Ignition Wiring (14.5 B&S)
Position: 4
1 HARNESS, Ignition Wiring (15HP Kohler Engines)
Position: 4
1 VALVE STEM, Snap In per front tire ass'y.
Position: 5
1 CLAMP, R. H. (for 2” Hose) (used on 8, 10 & 13 HP) (per rear tire ass'y)
Position: 5
1 CABLE, Clutch/Brake (54.32” long) used on 25”, 28” & 30” Models
Position: 5
1 BRACKET, Drive Support
Position: 5
1 PLATE, Differential
Position: 5
2 BEARING, .625 x 1.37 x .435
Position: 5
1 PLATE, Drive Disc
Position: 5
1 FILTER, Fuel (In-Line)
Position: 5
1 GASKET, Exhaust
Position: 5
1 HINGE, Deflector
Position: 5
1 NUT, 3/8-24 Hex Nyloc
Position: 5
1 SHOULDER BOLT, 3/8-24 x 9/16”
Position: 5
1 PULLEY, Hub (Powdered Metal)
Position: 5
1 LUBE FITTING, 3/16” Press-In
Position: 5
1 DECAL, European Noise Control (100 dB)
Position: 5
1 HOLDER, Fuse (Includes Fuse)
Position: 5
1 LUBE Fitting per front tire ass'y.
Position: 6
3 BOLT, 1/2-20 x 3/4” Lug, GR5 (per rear tire ass'y)
Position: 6
2 WASHER, 3/8” Flat SAE
Position: 6
2 BOLT, 5/16-18 x 3/4” Hex Flange Lock, GR5
Position: 6
4 SPACER, Pinion
Position: 6
1 WELDMENT, Sprocket & Shaft
Position: 6
4 NUT, 5/16-18 Hex Flange Lock, GR5 Was
Position: 6
4 CLAMP, Fuel Line replaces 12222 clamp
Position: 6
2 SPACER, .33 x .63 x .156
Position: 6
1 SPRING, Hinge
Position: 6
1 WASHER, 3/8” Flat SAE
Position: 6
1 WASHER, Flat 13/32" ID x 1.25" x 1/8" Thick ZP Was
Position: 6
2 NUT, 3/8-16 Hex Nyloc
Position: 6
1 SPINDLE, Shaft (10.237" Long)
Position: 6
1 DECAL Safety Instructions (French/German)
Position: 6
1 INTERLOCK MODULE, Briggs Was
Position: 6
1 INTERLOCK MODULE, Briggs & Kohler Was
Position: 6
2 WASHER, .77 x 1.13 x .06 Flat per front tire ass'y.
Position: 7
1 BOOT, Right Hand (8 & 10 HP) (per rear tire ass'y)
Position: 7
1 PAD, Pedal
Position: 7
2 CAP, Bumper
Position: 7
4 GEAR, Differential Pinion (12T 12P)
Position: 7
1 KEY,#5 Woodruff
Position: 7
1 ASSEMBLY, Brake Lever (Includes brake pad & rivet)
Position: 7
1 BRACKET, Fuel Tank (Rear)
Position: 7
1 NUT, 1/4-20 Hex Flange Lock Was
Position: 7
1 PIN, Hinge
Position: 7
1 PIVOT, Leveling
Position: 7
1 NUT, 3/8-24 Hex, GR B Was
Position: 7
2 IDLER PULLEY, 4” Idler
Position: 7
1 WASHER, .77 x 1.13 x .06 Flat
Position: 7
1 DECAL, Euro Community (CE)
Position: 7
1 HARNESS (Deck Interlock Wiring)
Position: 7
1 HUB CAP per front tire ass'y.
Position: 8
1 SEAL (per rear tire ass'y)
Position: 8
1 BUSHING, Nylon
Position: 8
6 NUT, 5/16-18 Hex Flange Lock, GR5 Was
Position: 8
1 WASHER, Thrust
Position: 8
1 CHAIN CASE HALF, Primary
Position: 8
1 RING, 3/8” External Retaining
Position: 8
2 SCREW, 5/16-18 x 1/2” Pan Head Self-Tap (Torx #T-40)
Position: 8
1 HEAT SHIELD, Muffler
Position: 8
1 NUT, 5/16-18 Hex Flange Lock, GR5 Was
Position: 8
1 WELDMENT, Rear Lift Arm
Position: 8
2 WASHER, 1/2” Flat SAE
Position: 8
2 SCREW, 3/8-16 x 1-1/2” Hex Head Cap, GR5
Position: 8
1 WASHER, Spindle
Position: 8
1 DECAL, Deflector French/German
Position: 8
1 FELT SEAL per front tire ass'y.
Position: 9
1 HUB, Rear Wheel R. H. (Weldment) (per right rear tire ass'y)
Position: 9
1 WELDMENT, Clutch Pedal
Position: 9
1 NUT, 5/16-24 Flange Lock (Large)
Position: 9
1 ASSEMBLY, Drive Hex Tube
Position: 9
2 BEARING, Needle
Position: 9
1 NUT, 1/4-28 Hex Top Lock
Position: 9
2 WASHER, 1/4” Split Lock
Position: 9
1 NUT 1/4-20 Hex Flange Lock Was
Position: 9
1 SCREW, 3/8-24 x 1-3/4” Hex Head Cap, GR5
Position: 9
1 BRACKET, Fixed Idler used on 33” Deck Models only
Position: 9
1 HOLDER, Blade
Position: 9
1 DECAL, Battery Storage
Position: 9
1 COVER, Battery Cable
Position: 9
1 CAP, Dust per front tire ass'y.
Position: 10
1 CAP, Hub (per rear tire ass'y)
Position: 10
4 BEARING, Nylon
Position: 10
1 SHIFT LINK, Long
Position: 10
1 WASHER, Nylon
Position: 10
2 THRUST WASHER, Nylon
Position: 10
1 WASHER, .28 x .63 x .06 Flat, GR5
Position: 10
2 SPACER, .33 x .63 x .156
Position: 10
2 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap
Position: 10
2 PUSH NUT, 1/4”
Position: 10
2 WASHER, 13/32 x 1-1/4” Flat
Position: 10
1 NUT, 1/4-20 Hex Flange Lock, GR5
Position: 10
1 BRACE, Fixed Idler Bracket used on 33” Deck Models only
Position: 10
1 SPACER, Blade Centering
Position: 10
1 DECAL Safety Instructions (English/Dutch)
Position: 10
1 WIRE, Positive (Red, 17” long)
Position: 10
1 COTTER PIN, 5/32 x 1” per front tire ass'y.
Position: 11
1 CAP, Hub, L. H. (Long Axle) (per left rear tire ass'y)
Position: 11
1 WELDMENT, Steering Shaft
Position: 11
1 WELDMENT, Shift Arm
Position: 11
1 GEAR, 11 Tooth, 10 Pitch
Position: 11
1 WELDMENT, Hub & Sprocket
Position: 11
1 SPACER, Brake Arm Pivot
Position: 11
1 VALVE, Fuel Shut-Off (Accessory) Was
Position: 11
1 SCREW, 1/4-20 x 3/4” Hex Head Cap, GR5
Position: 11
3 BOLT, 3/8-16 x 3/4” Hex Flange Lock Was
Position: 11
1 LEVER, Height of Cut
Position: 11
1 CABLE ASSEMBLY, No Reverse in Mow
Position: 11
5 SCREW, 5/16-18 x 1/2” Hex Washer Self-Tap
Position: 11
1 NUT, 5/8-18 Hex Center Lock Jam
Position: 11
1 DECAL, Deck/Chute International Warning
Position: 11
1 SWITCH, Ignition, 4 Terminal, Indak
Position: 11
1 SWITCH, Ignition-Afterfire Solenoid
Position: 11
1 TUBE, Inner (For 4.10/3.50 x 4 Tire) per front tire ass'y.
Position: 12
1 HUB, Rear Wheel L. H. (Weldment) (per left rear tire ass'y)
Position: 12
4 BUSHING, Tie Rod
Position: 12
1 CROSS BRACE
Position: 12
1 CHAIN, 46 Pitch (#35 Endless)
Position: 12
1 CHAIN, 46 Pitch (#35 Endless)
Position: 12
1 SCREW, 1/4-28 x 1” Hex Head Cap, (Washer Face) GR5
Position: 12
2 BOLT, 5/16-18 x 1/2” Hex Flange Nyloc
Position: 12
1 MUFFLER GUARD, Kohler
Position: 12
2 SCREW, 1/4-20 x 3-1/2” Hex Head w/Free Spinning Washer
Position: 12
1 NUT, 3/8-24 Hex Center Lock
Position: 12
1 CLIP, Cable
Position: 12
1 HANDLE, Blade Engagement (Flip)
Position: 12
2 SCREW, 1/2-20 x 1-1/4” Hex Head Cap, GR5
Position: 12
1 DECAL, Clutch Brake
Position: 12
1 WASHER, 5/8” Internal Tooth Lock Was
Position: 12
1 NUT, 5/16-24 Hex Lock, GR C Was 11201 (per rear tire ass'y)
Position: 13
1 TIE ROD, Left Hand (7.41” long)
Position: 13
1 SHFT LINK, Short (5/16-24 thread)
Position: 13
1 SPROCKET, 34T, 3/8P
Position: 13
10 SCREW, #10-24 x 1/2" Hex Washer Self-Tap (Torx) Was
Position: 13
1 SPRING, Torsional Brake Return
Position: 13
1 BRACKET, Muffler Guard (Kohler)
Position: 13
2 WASHER, 5/16” Flat Was
Position: 13
1 SPRING, Lever
Position: 13
1 BOLT, 1/4-20 x 3/4” Square Neck Carriage, GR5 Was
Position: 13
2 RING, 2” External Retaining
Position: 13
2 NUT, 1/2-20 Hex, GR5 or B
Position: 13
1 DECAL, Battery Caution, Multi-Language
Position: 13
1 NUT, 5/8-32 Hex
Position: 13
1 AXLE BOLT, Left Hand (per left rear tire ass'y)
Position: 14
1 KING PIN Weldment, Left Hand
Position: 14
1 NUT, 5/16-18 Hex, GR 5 or B Was
Position: 14
1 RING, 1-3/16” External Retaining
Position: 14
1 PLUG, 1/2” Cup Insert
Position: 14
1 SPRING, Clutch & Brake
Position: 14
1 HOSE, Fuel (1/4” I.D. x 3-1/2” long)
Position: 14
1 SCREW, 1/4-20 x 1” Hex Head Cap, GR5 Was
Position: 14
1 BOLT, 1/4-20 x 1/2” Hex Flange Lock
Position: 14
2 RING, Rear Lift Arm (Blue)
Position: 14
3 PIN, 3/32 x 3/4” Cotter Was
Position: 14
1 DECAL, Patent Numbers
Position: 14
1 IGNITION KEY, Pair
Position: 14
1 WHEEL BOLT, Right Hand (per right rear tire ass'y)
Position: 15
1 TIE ROD, Right Hand (7.41” long)
Position: 15
1 WELDMENT, Arm, Shift Handle
Position: 15
1 SPACER, Differential Case
Position: 15
1 ROLLER, 1-3/8 Long
Position: 15
1 LIFT, Yoke
Position: 15
2 BRACKET, Seat
Position: 15
2 SCREW, 1/4-20 x 5/8” Hex Head w/Free Spinning Washer Was
Position: 15
1 KIT, Air Lift used on 25”, 28” & 33” Decks
Position: 15
1 GUIDE, Belt
Position: 15
1 SPRING, Extension, 4” x 1/2” Diameter
Position: 15
1 DECAL Deflector Caution (English/Dutch)
Position: 15
3 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap Was
Position: 15
1 KING PIN Weldment, Right Hand
Position: 16
1 SPRING, Shift Detent
Position: 16
2 BOOT CLAMP (for 2” Hose)
Position: 16
1 RING, 1/2” External Retaining (Heavy Duty)
Position: 16
2 BEARING, Yoke
Position: 16
4 BOLT, 5/16-18 x 1” Square Neck Carriage, GR5
Position: 16
2 AIR-LIFT (33” Models)
Position: 16
2 SPRING, Assist
Position: 16
1 WELDMENT, Idler Arm
Position: 16
1 DECAL, 28 Inch (Hi-Vac)
Position: 16
1 SWITCH, Operator Presence Control (OPC) Traction (NC/NO)
Position: 16
1 WELDMENT, Front Axle, Narrow used on 25”, 28” & 30” Models
Position: 17
1 ASSEMBLY, Speed Adjustment Latch Includes Spring, Part Number
Position: 17
1 BOOT, Oil Seal (Short Axle)
Position: 17
1 FENDER, Left Hand (1.628” I. D. Hole) used on 25” & 28” Deck Models
Position: 17
2 NUT, 5/16-24 Hex Center Lock Was
Position: 17
2 NUT, 5/16-18 Hex Flange Top Lock
Position: 17
2 WASHER, .28 x .63 x .06 Flat, GR5
Position: 17
6 SCREW, 5/16-24 x 11/16” Oval Head Machine
Position: 17
1 BRACE, Top
Position: 17
1 SPACER, .39 x 1.0 x .31 Nylon
Position: 17
1 DECAL, 33 Inch (Hi-Vac)
Position: 17
5 NUT, 1/4-20 Hex, GR5 or B
Position: 17
1 HARNESS WIRE, Operator Presence Control (OPC)
Position: 17
4 NUT, 1/4-20 Hex Was
Position: 17
2 FOOT PAD, Short
Position: 18
1 WELDMENT, Shift Handle
Position: 18
1 PLUG, 1/2” Cup Insert
Position: 18
1 COLLAR, Lock (Incl. P/N 90776 Set Screw, 1/4-20 x 1/4”) used with ball bearing, item
Position: 18
2 SCREW, 5/16-24 x 1” Hex Head Cap, GR5
Position: 18
6 WASHER, 5/16” Internal Tooth Lock
Position: 18
1 ROD, Leveling (3/4-24 thread)
Position: 18
1 GRIP, Handle
Position: 18
1 DECAL, Back-Up Recoil (33” Kohler Engine Models)
Position: 18
2 WASHER,1/4” Internal Tooth Lock
Position: 18
1 SPRING, Parking Brake Latch
Position: 19
2 HAIR PIN, 3/32 x 1-1/2”
Position: 19
1 CASE, Transmission
Position: 19
1 BEARING, Left Hand Fender (Includes item 20) used on 25” & 28” Models- 8,
Position: 19
1 SCREW, 3/8-16 x 5/8” Hex Washer Self-Tap
Position: 19
6 NUT, 5/16-24 Hex Was
Position: 19
1 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
Position: 19
2 WASHER, 3/8” Flat Was
Position: 19
1 DECAL, OHV (33” Kohler Engine Models)
Position: 19
2 SCREW, 1/4-20 x 5/8” Hex Head Cap. GR5 Was
Position: 19
2 SCREW, 1/4-20 x 5/8” Hex Head Cap. GR 5 Was
Position: 19
2 SCREW, 1/4-20 x 5/8” Hex Head Cap, GR5 Was
Position: 19
2 WASHER, .66 x 1.31 x .09 Flat
Position: 20
1 GRIP, Shift Handle
Position: 20
1 GASKET, Transmission Case
Position: 20
1 FITTING, Lube, 45 Degree, 3/16” w/Hex
Position: 20
1 COLLAR, Yoke
Position: 20
2 SCREW, 1/2-20 x 1” Hex Head Cap, GR5
Position: 20
1 ASSEMBLY, Clutch Plate
Position: 20
1 DRUM, Brake Spindle
Position: 20
1 DECAL, SNAPPER
Position: 20
1 WIRE, Negative, Black (15” long)
Position: 20
2 BUSHING, Nylon
Position: 21
2 WING, Rear
Position: 21
1 FENDER, Right Hand (2.498” Dia. Hole) 33” Deck Ball Bearing
Position: 21
1 TIE ROD (5/16-24 thread- both ends)
Position: 21
2 FENDER WASHER, 5/16”
Position: 21
2 WASHER, 1/2” Internal Tooth Lock
Position: 21
1 RAIL, Deck Lift, Right Hand Was
Position: 21
1 PIN, 1/4 x 1-5/8” Clevis
Position: 21
1 DECAL, Brake Operation (Italian)
Position: 21
1 HARNESS, Operator Presence Control (OPC) Wire
Position: 21
2 NUT, 1/4-20 Hex, GR 5 or B attaches to starter terminal
Position: 21
1 HARNESS, Operator Presence Control (OPC) Wire
Position: 21
1 HAIR PIN 2-1/4”
Position: 22
1 BUSHING, Pilot Was
Position: 22
1 GEAR, 63 Tooth 10 Pitch
Position: 22
1 ARM, Yoke
Position: 22
2 NUT, 1/2-20 Hex Jam
Position: 22
1 RAIL, Deck Lift, Left Hand
Position: 22
1 BAND, Brake (Formed)
Position: 22
1 DECAL, Brake Operation (Spanish)
Position: 22
2 RETAINER, 1/4” Bolt
Position: 22
1 NUT, 1/4-20 Hex, GR5 or B
Position: 22
1 FOAM COVER, Steering Shaft
Position: 23
1 BRACKET, Switch
Position: 23
1 AXLE, Long Was
Position: 23
1 BOOT, Rear Axle, Thick Flange
Position: 23
2 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap Was
Position: 23
2 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR5
Position: 23
1 DETENT, Height Adjust
Position: 23
1 DECAL, Height of Cut
Position: 23
2 CABLE TIE, 7”
Position: 23
2 NUT, 1/4-20 Hex Center Lock, GR 5 or B
Position: 23
1 PIN, 3/16 x 1” Cotter
Position: 24
1 PIN, 3/32 x 3/4” Cotter Was
Position: 24
1 SPACER, Differential Case
Position: 24
1 THRUST WASHER
Position: 24
1 STUD, Clutch Link (3/8-24 thread)
Position: 24
4 SCREW, 1/4-20 x 5/8” Hex Head w/Free Spinning Washer Was
Position: 24
2 SCREW, 3/8-16 x 1” Hex Washer Self-Tap
Position: 24
4 WASHER, 1/4” Flat Was
Position: 24
1 DECAL, Service Parts, Euro
Position: 24
2 NUT, 1/4-20 Hex Center Lock, GR5 or B
Position: 24
2 WASHER, 3/8” Flat Was
Position: 25
1 PIN, 1/4 x 1-3/4” Tapered Clevis
Position: 25
1 ASSEMBLY, Short Axle, 23T (Includes Gear) Use only with Long Axle P/N
Position: 25
1 WASHER, 3/8” Internal Tooth Lock
Position: 25
3 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR5 Was
Position: 25
1 SPACER, Detent
Position: 25
1 EYE-BOLT, 1/4-20 x 4”
Position: 25
1 DECAL, Caution, Fuel Leakage (English)
Position: 25
1 CABLE TIE, 3.19” long
Position: 25
1 SWITCH, Seat (Normally Closed)
Position: 25
1 PIN, 3/16 x 1-1/2” Cotter Was
Position: 26
1 BUSHING, 3/4 x 1.62 Flange (Nylon)
Position: 26
4 BOLT, 5/16-24 x 1-5/8” Hex Special Lock (Vibresist)
Position: 26
1 NUT, 5/8-18 Hex Nyloc
Position: 26
1 NUT, 3/8-24 Hex, GR5 or B
Position: 26
1 COVER, 25” Mulcher
Position: 26
3 SCREW, 3/8-16 x 5/8” Hex Washer Self-Tap
Position: 26
1 SPRING, Torsion, Flip Handle
Position: 26
1 DECAL, Caution, Fuel Leakage (Dutch)
Position: 26
1 SWITCH, Seat (NC) used on 11 & 13HP Engines
Position: 26
1 SWITCH, Seat (NC)
Position: 26
2 PIN, 5/32 x 1” Cotter Was
Position: 27
2 WASHER, Thrust
Position: 27
2 O-RING, 5/16"
Position: 27
1 BRACKET, Slide
Position: 27
9 NUT, 3/8-16 Hex Flange Lock Was
Position: 27
1 GRIP, Height Adjustment Lever
Position: 27
1 PIN, 3/16 x 1” Clevis
Position: 27
1 DECAL, Caution, Fuel Leakage (German)
Position: 27
1 RING, 1/2” External Retaining (Heavy Duty)
Position: 28
2 BUSHING, 3/4 x I.O. Flange (Nylon)
Position: 28
2 WASHER, 5/16” Belleville
Position: 28
2 O-RING, 1/2 x 5/8”
Position: 28
1 PIN, 3/32 x 3/4” Cotter Was
Position: 28
3 NUT, 3/8-24 Hex Nyloc
Position: 28
2 RING, Front Lift Arm (Red)
Position: 28
1 WELDMENT, Blade Engagement Handle
Position: 28
1 DECAL, Caution, Fuel Leakage (French)
Position: 28
2 RING, 5/8” External Retaining
Position: 29
14 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
Position: 29
1 WASHER, 5/16” External Tooth Lock
Position: 29
1 SPACER, Nylon
Position: 29
2 SLIDE HALF
Position: 29
3 SCREW, 3/8-24 x 3-3/4” Hex Head Cap, GR5
Position: 29
1 ARM, Front Lift
Position: 29
1 SPRNG, Blade Handle
Position: 29
1 DECAL, Caution, Fuel Leakage (Italian)
Position: 29
2 PIN, 1/8 x 3/4” Cotter Was
Position: 30
2 SCREW, #10-32 x 1/4” Hex Washer Self-Tap
Position: 30
1 WASHER, .34 x .69 x .08 Flat
Position: 30
1 WASHER, Shim or quantity as required
Position: 30
1 BOLT, 5/16-18 Shoulder
Position: 30
3 WHEEL, Gage
Position: 30
1 WELDMENT, Front Lift Arm
Position: 30
1 ROD, Idler Control
Position: 30
1 DECAL, Caution, Fuel Leakage (Spanish)
Position: 30
6 WASHER, .77 x 1.13 x .06 Flat
Position: 31
4 WASHER, 5/16” Flat Was
Position: 31
1 SCREW, 5/16-24 x 2-5/8” Hex Head Cap
Position: 31
6 WASHER, Shim .625 x .875
Position: 31
1 WASHER, 5/16” Split Lock
Position: 31
3 SPACER
Position: 31
1 PIN, 1/8 x 3/4” Cotter Was
Position: 31
1 SCREW, #10-32 x 1” Hex Washer Head Self-Tap
Position: 31
1 DECAL, Safety Instructions (Spanish/Italian)
Position: 31
1 COVER, Steering Shaft
Position: 32
1 CLIP, Wire
Position: 32
11 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
Position: 32
1 BALL BEARING, Left Hand Fender for 33” Deck Models
Position: 32
1 NUT, 5/16-18 Hex, GR 5 or B Was
Position: 32
1 BRACKET, Gage Wheel (Front)
Position: 32
1 ROD, Deck Support (Front Lift Arm to Front End)
Position: 32
1 SWITCH, Deck Interlock (NO)
Position: 32
1 DECAL, No Mow in Reverse (Euro)
Position: 32
1 HOLDER, Bottle (Wire)
Position: 33
1 WASHER, 5/16” Internal Tooth Lock
Position: 33
13 SCREW, 1/4-20 x 5/8” Hex Washer Head Self-Tap Was
Position: 33
GREASE, Transmission (Use 2 oz. Maximum)
Position: 33
2 BRACKET, Gage Wheel (Rear)
Position: 33
1 RING, .438 External Retaining
Position: 33
1 MOUNT, Handle/Switch
Position: 33
1 DECAL, Engine, B&S E10 Powerbuilt
Position: 33
2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap (Torx)
Position: 34
4 SCREW, 5/16-18 x 1-1/2” Hex Washer Self-Tap Was
Position: 34
1 SPACER, Short Axle
Position: 34
1 ASSEMBLY, Leaf Spring
Position: 34
6 BOLT, 5/16-18 x 1/2” Short Neck Carriage, GR5
Position: 34
2 SCREW, 5/16-18 x 1/2” Hex Washer Self-Tap
Position: 34
2 SCREW, 1/4-20 x 5/8” Hex Washer Head Self-Tap Was
Position: 34
1 BOTTLE, Water
Position: 35
4 SCREW, 5/16-24 x 1-3/4” Hex Head Cap, GR5
Position: 35
GREASE, Transmission (24 oz. Required)
Position: 35
8 NUT, 5/16-18 Hex Flange Lock, GR5 Was
Position: 35
2 SPACER, Deck Lift
Position: 35
1 PIN, 3/32 x 1/2” Cotter Was
Position: 35
1 CABLE, Brake (29” long)
Position: 36
4 RETAINER, 5/16” Bolt
Position: 36
2 NUT, 5/16-18 Wing Was
Position: 36
1 BOLT, #10-24 x 1” Flat Head Square Neck
Position: 36
1 NUT, 1/4-20 Hex Top Lock Was
Position: 36
2 CONNECTOR, Cable
Position: 37
1 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR5 Was
Position: 37
1 BLADE, 25” Mulcher
Position: 37
1 NUT, #10-24 Hex Nyloc
Position: 37
1 BUSHING, Flange .27 x .35 x .4
Position: 37
1 SCREW, 1/4-20 x 3/4” Hex Head Cap, GR5
Position: 38
4 SCREW, 5/16-18 x 3/4” Hex Washer Self-Tap
Position: 38
1 BLADE, 25”
Position: 38
1 ANCHOR
Position: 38
1 SPRING, Rectangular Wire Die, Blue
Position: 38
1 NUT, 1/4-20 Hex Center Lock, GR5 or B
Position: 39
2 SWIVEL, Adjustable
Position: 39
1 BLADE, Ninja, 25”
Position: 39
2 SCREW, 5/16-24 x 3/4” Hex Head Cap, GR5
Position: 39
1 RESTRICTOR, Belt
Position: 39
1 COVER, Switch
Position: 40
2 WASHER, 5/16” Internal Tooth Lock
Position: 40
1 COVER, Battery
Position: 41
7 FASTENER, 1/4” Ratchet
Position: 42
1 SHOULDER BOLT, 5/16-18
Position: 43
1 LEVER, Over-Ride
Position: 44
1 WASHER, .47 x .92 x .065 Flat
Position: 45
1 NUT, 5/16-18 Hex Nyloc
Position: 46
1 OIL DRAIN, Short
Position: 47
1 ASSEMBLY, Oil Valve
Position: 48
1 PLATE, Engine (Kohler Engine) used on E331523KVE Model
Position: 49
7 WASHER, .32 x .58 x .08 Split Lock
Position: 50
1 WASHER, .32 x .58 x .08 Split Lock
Position: 50
1 BOLT, M8-1.25 x 25mm, Self-Tap (Kohler)
Position: 51
4 SCREW, 5/16-24 x 1” Hex Head Cap, GR5
Position: 52
7 NUT, 5/16-24 Hex, GR5
Position: 53
1 NUT, 5/16-24 Hex, GR5
Position: 53
1 TUBE CLAMP
Position: 54
1 SCREW, 5/16-24 x 2-1/2” Hex Head Cap, GR5
Position: 55
2 PLUG, 1/2” Cup Insert
Position: 7011024
1 BUSHING, Tie Rod
Position: 7013321
2 BUSHING, Tie Rod
Position: 7013321
2 KNOB, Seat Adjusting (5/16-18 thread)
Position: 7023191
2 KNOB, Seat Adjusting, 5/16-18 thread
Position: 7023735
2 SPACER, Pivot
Position: 7028395
1 SWITCH, Seat (NC)
Position: 7029211
1 KIT, Tire Chains (16 x 4.50-8 Tires) Was 60358 (All Rear Engine
Position: 7060049
1 KIT, Drive Disc Puller used on All RER Aluminum
Position: 7060325
1 KIT, Tire Chains (16 x 6.50-8 Tires) used on All Rear Engine Riders
Position: 7060357
1 KIT, Wheel Weight (8” Wheels) used on All Rear Engine Riders
Position: 7060517
1 KIT, Dump Cart used on All Rear Engine Riders
Position: 7060697
1 KIT, Gage Wheel used on All 33” Deck Rear
Position: 7060737
1 KIT, Single Bag Catcher used on All 25” Deck Rear
Position: 7060941
1 KIT, Single Bag Catcher used on All 28” & 33” Deck Rear
Position: 7060943
1 KIT, Bag-N-Wagon used on All 28” & 33” Deck Rear
Position: 7060947
1 KIT, 28” Thatcherizer used on All series 7 & Newer
Position: 7060948
1 KIT, 36” Dozer Blade used on All Rear Engine Riders
Position: 7060959
1 KIT, Wagon Cover used on All 28” & 33” Deck Rear
Position: 7060964
1 KIT, Ninja Recycling Cover used on All 25” Deck Rear
Position: 7061049
1 KIT, Ninja Recycling Cover used on All 28” Deck Rear
Position: 7061253
1 KIT, Ninja Recycling Cover used on All 33” Deck Rear
Position: 7061255
1 KIT, Twin Bag Catcher used on All 28” & 33” Deck Rear
Position: 7063281
1 KIT, Front Weight Was 61190 (used on All series
Position: 7072416
2 NUT, 5/16-18 Hex Large Flange Center Lock
Position: 7090951
4 BOLT, 5/16-18 x 1/2” Hex Flange Nyloc
Position: 7091038
2 PIN, 5/32 x 1” Cotter
Position: 7091516