Reparatur-Assistent
Powered by ChatGPT
Ersatzteilliste
Battery
Position: 1
Chassis Stamping
Position: 1
Steering Wheel
Position: 1
Seat 13 121248X Bushing, Snap
Position: 1
Decal, Fender DB/CE 15 136832 Decal, V-Belt Sch
Position: 1
Valve Cap, Tire
Position: 1
Control, Throttle
Position: 1
Lift Lever Inner Wire Assembly
Position: 1
Mower Housing Assembly 88 19111216 Washer 11/32 x 3/4 x 16 Ga.
Position: 1
Transaxle Cover
Position: 1
Cylinder Assembly 108 690464 Valve-Choke (Manual Choke)
Position: 1
Drawbar
Position: 2
Spring Brake Return 69 142432 Screw Hex Wsh Hi-Lo 1/4-1/2 unc
Position: 2
Axle Assembly STMP Dropped STL
Position: 2
Bracket, Pivot, Seat 14 72050412 Bolt, Carriage 1/4-20 x 1-1/2
Position: 2
Decal, HP Engine 16 182166 Decal, Cutfinger
Position: 2
Shaft Assembly, Lift
Position: 2
Kit-Bushing/Seal (Magneto Side) 108A 692344 Valve-Choke (Choke A Matic)
Position: 2
Spindle Assembly, L.H.
Position: 3
Decal, Hood RH 17 159737 Decal, Brake/Clutch Symbol
Position: 3
Bracket Asm. Fram Sway Bar 92 73800600 Nut Lock Hex w/Ins. 3/8-16
Position: 3
Transaxle Case
Position: 3
• Seal-Oil (Magneto Side) 117 694352 Ø Jet-Main (Standard)
Position: 3
Spindle Assembly, R.H.
Position: 4
Decal, Brake Parking 19 159736 Decal, Chassis Hot Muffler
Position: 4
Muffler
Position: 4
Bracket, Asm. Deck Sway Bar 96 74930620 Bolt 3/8-16 x 1-1/4
Position: 4
Countershaft
Position: 4
Sump-Engine 118 697228 Jet-Main (High Altitude)
Position: 4
Bumper Hood/Dash
Position: 5
Clip, Push-In Hinged 17 123976X Locknut, Flange 1/4 Gr.
Position: 5
Decal, Hood LH -- 162598 Decal, Drawbar Load Limit
Position: 5
Output Shaft
Position: 5
Head-Cylinder 121 697241 Kit-Carburetor Overhaul
Position: 5
Bar Sway Deck 98 19132016 Washer 13/32 x 1-1/4 x 16 Ga.
Position: 6
Spur Gear (38 teeth)
Position: 6
Decal, Dflctr Warning Ctfngr Sym -- 138311 Decal, Lift Handle
Position: 7
Spur Gear (11 teeth)
Position: 7
•+ Gasket-Cylinder Head 125 697190 Carburetor
Position: 7
Box Battery Fender
Position: 8
Rod Shift Fender Adjust 77 123583X Key, Square
Position: 8
Decal, V-Belt Drive Sch Trace CE -- 184310X428 Pad, Footrest LH STLT
Position: 8
Bolt, Hex 3/8-24 x 1-1/4 Gr. 8 99 10040600 Washer Lock Hvy Hlcl Spr. 3/8
Position: 8
Shift Key
Position: 8
Decal, Fender -- 184311X428 Pad, Footrest RH STLT
Position: 9
Shift Collar
Position: 9
• Gasket-Breather 127 695005 Plug-Welch
Position: 9
Draglink
Position: 10
Pan, Seat
Position: 10
Decal, Battery, Dngr/Psn Eng -- 197463 Operator's, Manual, Euro
Position: 10
Washer, Hard Blade Mower Vented 101 132803 Cover Asm Mulching 38"
Position: 10
Shift Rod & Fork
Position: 10
Screw (Breather Assembly) 130 691750 Valve-Throttle
Position: 10
Panel, Dash, L.H.
Position: 11
Knob Seat NOTE: All component dimensions given in U.S. inches
Position: 11
Decal, Read Owner's Manual -- 197464 Operator's, Manual, Scan
Position: 11
Link, Lift, L.H.
Position: 11
Blade, 38" Mulching Std 107 133502 Spacer, Retainer
Position: 11
Bevel Gear (30 teeth)
Position: 11
Tube-Breather 131 494379 Kit-Throttle Shaft
Position: 11
Decal, Engine Wrng Symbols -- 197465 Manual, Parts
Position: 12
Link, Lift, R.H.
Position: 12
Input Bevel Pinion (13 teeth)
Position: 12
• Gasket-Crankcase 133 494381 Float-Carburetor
Position: 12
Spacer Brg Axle Front
Position: 13
Gasket
Position: 13
Shaft and Bearing Assembly 108 133503 Stiffener, Idler Arm
Position: 13
Bevel Gear (13 teeth) (Include. 14)
Position: 13
Screw (Cylinder Head) 137 281165 ؇ Gasket-Float Bowl
Position: 13
Decal, Panel Dash
Position: 14
Tube Drain Oil Easy
Position: 14
Mandrel Housing, Vented 110 142587 Upstop Deck Front 38"
Position: 14
Bevel Pinion (13 teeth) (Include 13)
Position: 14
Nut, Hexflange Lock
Position: 15
Link, Front
Position: 15
Ring Gear (43 teeth)
Position: 15
Plug-Oil Drain 141 495097 Kit-Choke Shaft (Manual Choke)
Position: 15
Switch, Interlock
Position: 16
Stripper, Mower, Vented 122 131289 Rod, Brake, LH
Position: 16
Crankshaft 141A 495931 Kit-Choke Shaft (Choke A Matic)
Position: 16
Shaft Assembly, Steering
Position: 17
Trunnion
Position: 17
Drive Pin
Position: 17
Bumper Extrusion
Position: 18
Spacer 1.130 x .695
Position: 18
Arm, Suspension, Rear
Position: 19
Bolt, Shoulder 123 169971 Rod, Brake, RH
Position: 19
Retainer Spring
Position: 20
• Seal-Oil (PTO Side) 142 697140 Ø Nozzle-Carburetor
Position: 20
Harness Asm Light W/4152j
Position: 21
Set Screw 3 / 8-16 x 3 / 8”
Position: 21
Rod, Brake 96 4497H Retainer Spring 1" Zinc/Cad
Position: 22
Spring .310 OD x .625 L
Position: 22
Screw (Crankcase Cover/Sump) 146 691639 Key-Timing
Position: 22
Shield Brn/Dbr Guard
Position: 23
Bracket, Mower Deflector 130 74780616 Bolt Fin Hex 3/8-16 unc x 1 Gr.
Position: 23
Flywheel 186 698174 Connector-Hose
Position: 23
Key-Flywheel 187 697098 Line-Fuel
Position: 24
Cable Battery 6 Ga. w/16 wire red
Position: 25
Piston Assembly (Standard) 188 691693 Screw (Control Bracket)
Position: 25
Fuse 20 AMP
Position: 26
Retaining Ring (pkg of 2)
Position: 26
Ring Set (Standard) 216 691840 Link-Choke
Position: 26
Retaining Ring
Position: 27
Lock-Piston Pin 232 691842 Spring-Governor
Position: 27
Grille Lens Asm (Include Key #'s 29 and 212)
Position: 28
Rod, Parking Brake 120 73900600 Nut Lock Flg 3/8-16
Position: 28
Retaining Ring
Position: 28
Pin-Piston 238 691843 Cap-Valve
Position: 28
Cap, Parking Brake 150 175456 Spacer Retainer
Position: 29
Arrestor, Spark
Position: 29
Thrust Washer .627 ID x .031W
Position: 29
Rod-Connecting (Standard) 240 394358 Filter-Fuel
Position: 29
Switch Ign
Position: 30
Bracket, Transaxle 151 19133210 Washer 13/32 x 2 x 10 Ga.
Position: 30
Screw, Thdro 158 17720408 Screw Hex Thd Cut 1/4-20 x 1/2
Position: 30
Cup Washer 1.127 ID x .032W
Position: 30
Bracket, Fender Support
Position: 31
Tank, Fuel
Position: 31
Bearing, Pvt, Lift
Position: 31
Washer, Spacer 185 188234 Head Asm. Cable Clutch
Position: 31
Flat Washer .750 ID x .056
Position: 31
Rod, Tie
Position: 32
Cap Assembly Fuel
Position: 32
Pulley, Mandrel -- 130794 Mandrel Assembly (Includes Hous-
Position: 32
Oil Seal 5 / 8”
Position: 32
Screw (Connecting Rod) 265 691024 Clamp-Casing
Position: 32
Key Ign Molded Craftsman
Position: 33
Nut, Flangelock 9/16 ing, Shaft and Shaft Hardware
Position: 33
Valve-Exhaust 267 695134 Screw (Casing Clamp)
Position: 33
Shaft, Foot Pedal 158 165589 Bracket Shift Mount
Position: 34
Bushing .563
Position: 34
Valve-Intake 276 692255 ؇ Washer-Sealing
Position: 34
Flanged Bushing 5 / 8” ID
Position: 35
Spring-Valve (Intake) 304 698402 Housing-Blower
Position: 35
Bushing, Steering
Position: 36
Pulley, Idler, Flat Only-Pulley Not
Position: 36
Brake Disk
Position: 36
Spring-Valve (Exhaust) 305 697102 Screw (Blower Housing)
Position: 36
Screw
Position: 37
Line, Fuel
Position: 37
Brake Pad Plate
Position: 37
Guard-Flywheel 305A 697103 Screw (Blower Housing)
Position: 37
Bracket Asm. Pivot Mower Rear
Position: 38
Pulley, Composite, Flat 163 74780416 Bolt Hex Fin 1/4-20 unc x 1 Gr.
Position: 38
Insert, Steering Wheel
Position: 38
Plug, Drain Oil Easy
Position: 38
Brake Pad (pkg of 2)
Position: 38
Bracket Pivot
Position: 39
Dowel Pin
Position: 39
Harness Ign
Position: 40
Retainer-Valve 306 697107 Shield-Cylinder
Position: 40
Keeper, Belt Idler 166 17490510 Screw 5/16-18 x 5/8
Position: 41
Adaptor, Steering Wheel
Position: 41
Cover Terminal Red
Position: 42
Solenoid
Position: 43
Locknut 5 / 16 -
Position: 43
Slinger-Governor/Oil 307 691003 Screw (Cylinder Shield)
Position: 43
Extension Shaft Steering
Position: 44
Brake Pad Holder
Position: 44
Spacer .2625 x 1.0
Position: 45
Tappet-Valve 309 693551 Motor-Starter
Position: 45
Brake Lever Bracket
Position: 46
Camshaft 309A -- -- -- -- Motor-Starter (For Replacement Starter
Position: 46
Pulley, Idler, V-Groove 168 165492 Bolt Shoulder 5/16-18 x .561
Position: 47
Fitting, Grease
Position: 47
Axle (11 - 15 / 16 “ long)
Position: 47
Ammeter Adapter
Position: 48
Bellcrank, Clutch 169 165580 Plate Fastening
Position: 48
Axle (16 - 1 / 2” long)
Position: 48
Short Block (31C707-0230-E2 Replace- Motor,
Position: 48
Spur Gear (29 teeth)
Position: 49
Spur Gear (23 teeth)
Position: 50
Manifold-Intake 311 497608 Brush Set
Position: 50
Spur Gear (19 teeth)
Position: 51
•Ø‡+ Gasket-Intake 311A 395538 Brush Set
Position: 51
Protection Wire Loop
Position: 52
Spur Gear (16 teeth)
Position: 52
Brake Assembly (Std. Deck - Order separately
Position: 53
Spur Gear (15 teeth)
Position: 53
Spur Gear (15 teeth - steel)
Position: 53
Stud (Carburetor) 333 492341 Armature-Magneto
Position: 53
Washer Hardened mulcher cover components key nos.
Position: 54
Screw (Intake Manifold) 334 691061 Screw (Magneto Armature)
Position: 54
Idler Arm Assembly 96-101)
Position: 55
Spacer, Retainer
Position: 56
Spur Gear (11 teeth)
Position: 56
V-Belt 275 19131614 Washer 13/32 x 1 x 14 Ga.
Position: 57
Spur Gear (17 teeth)
Position: 57
Spur Gear (21 teeth)
Position: 58
Keeper, Center Span
Position: 59
Spur Gear (24 teeth)
Position: 59
Spur Gear (25 teeth)
Position: 60
Pulley, Engine 1 inch = 25.4 mm
Position: 63
Countershaft Spacer 1 - 1 / 8” x 3/8”
Position: 63
Dash Lower STLT
Position: 64
Bolt Hex 7/16-20 x 4 x Gr.
Position: 64
Brake Shaft Spacer 1 - 3 / 8” x 3 / 8”
Position: 64
Spacer Brace Axle
Position: 65
Flat Washer .563 ID x .062W
Position: 65
Input shaft
Position: 66
Knob
Position: 67
Shifter & Brake shaft
Position: 67
Axle, Brace
Position: 68
Belt
Position: 68
Retaining Ring
Position: 69
Spacer .890
Position: 70
Steering Asm
Position: 71
Square Cut Ring
Position: 71
Screen-Rotating 337 691043 Plug-Spark
Position: 73
Screw (Rotating Screen) 358 697151 Gasket Set-Engine
Position: 74
Washer (Flywheel) 363 19203 Flywheel Puller
Position: 75
Flat Washer 1.128 ID x .058W
Position: 76
Screw (Flywheel Guard) 383 89838 Wrench-Spark Plug
Position: 78
Spring .430 OD x .5000 L
Position: 79
Bracket Susp Chassis Front
Position: 82
Bevel & Spur Gear (30 & 13 teeth)
Position: 82
Spur Gear (27 teeth)
Position: 83
Oill Fill Plug
Position: 85
Runner, RH 1 inch = 25.4 mm
Position: 87
Bolt Shoulder 7/16-20
Position: 88
Cover Battery Terminal
Position: 90
Clip Steering
Position: 91
Ø Bushing-Throttle Shaft RPM Settings: Low Speed: 1900-2100
Position: 93
Kit-Idle Mixture High Speed: 3000-3200
Position: 94
Washer Harden .793 x 1.637 x .060
Position: 95
Screw (Throttle Valve)
Position: 95
Kit-Idle Speed • Included in Engine Gasket Set, Key. No.
Position: 98
Ø Pin-Float Hinge Ø Included in Carburetor Overhaul Kit, Key. No.
Position: 104
Ø Valve-Float Needle ‡ Included in Carburetor Gasket Set, Key. No.
Position: 105
Ø Seat-Inlet + Included in Valve Gasket Set, Key. No.
Position: 106
Plate Reinforcement STLT
Position: 142
Bracket Swaybar Chassis
Position: 143
Bracket Pnt Footrest STLT
Position: 144
Jod Pivot Chassis/Hood
Position: 145
Bolt Shoulder 5/16 -18 TT
Position: 206
Insert Lens Reflective
Position: 212
Screw 10 x 3/4 Single Lead-Hex
Position: 278
Washer (Governor Crank) 868 690968 •+ Seal-Valve
Position: 404
Elbow-Intake 876 495877 Kit-Pinion Spring
Position: 431
Filter-Air Cleaner Cartridge 877 393456 Wire-Connector/Alternator
Position: 445
Washer (Starter Cable) 896 691641 Pin-Drive Retainer
Position: 462
Alternator 914 690960 Screw (Rocker Cover)
Position: 474
Strap-Starter 947 694393 Solenoid-Fuel
Position: 503
Nut (Governor Control Lever) 950 691657 Screw (Float Bowl)
Position: 505
Drive-Starter 967 697015 Filter-Pre Cleaner
Position: 510
Clutch-Drive 975 495933 Bowl-Float
Position: 513
Dipstick 977 690192 Gasket Set-Carburetor
Position: 523
• Seal-Dipstick Tube 987 691326 Ø Seal-Throttle Shaft
Position: 524
Tube-Dipstick 1005 697853 Fan-Flywheel
Position: 525
Starter-Armature 1019 697143 Kit-Label
Position: 544
Bushing-Governor Crank 1023 692492 Cover-Rocker Arm
Position: 552
Screw (Remote Choke) 1026 692003 Rod-Push (Intake)
Position: 559
Bolt (Governor Control Lever) 1029 691751 Arm-Rocker
Position: 562
Nut (Starter Cable) 1034 690822 Guide-Push Rod
Position: 579
Cover-Breather Passage 1036 695700 Label-Emission
Position: 584
Clamp-Hose 1040 698368 Plate-Trim
Position: 601
Pin-Cotter 1044 691658 Screw (Flywheel)
Position: 614
Crank-Governor 1051 691265 Ring-Retaining
Position: 616
Ø • Seal-O Ring (Intake Manifold) 1058 275038 Owner’s Manual
Position: 617
Ø Spring/Seal Assembly (Manual Choke) 1059 698516 Kit-Screw/Washer
Position: 634
Boot-Spark Plug 1083 691626 Nut (Starter Terminal)
Position: 635
Retainer-Air Filter 1083A 690958 Nut (Starter Terminal)
Position: 643
Nut (Carburetor) 1090 691293 Retainer-Brush
Position: 654
• Seal-Governor Shaft 1091 691333 Cap-Limiter
Position: 691
Screw (Drive Cap) 1095 691581 Gasket Set-Valve
Position: 697
Pin-Locating 1119 691183 Screw (Alternator)
Position: 718
Clip-Wire 1263 697124 Reed-Breather
Position: 729
Gear-Timing 1264 697104 Screw (Breather Reed)
Position: 741
Link-Counterweight 1265 697125 Support-Blower Housing
Position: 757
Counterweight 1266 691917 •Ø Seal-O Ring (Intake Elbow)
Position: 758
Pin-Counterweight 1266A 697123 Ø Seal-O Ring(Intake Elbow)
Position: 759
Gear-Pinion 1267 697575 Latch-Blower Housing
Position: 783
Harness-Wiring 1279 690960 Screw (Blower Housing Support)
Position: 789
Nut (Brush Retainer) RPM Settings: Low Speed: 1900-2100
Position: 797
Cap-Drive High Speed: 3000-3200
Position: 801
Cap-End • Included in Engine Gasket Set, Key. No.
Position: 802
Housing-Starter ‡ Included in Carburetor Gasket Set, Key. No.
Position: 803
Stud (Rocker Arm)
Position: 830
• Seal-O Ring (Dipstick Tube) NOTE: All component dimensions given in U.S. inches 1 inch
Position: 842
Dipstick/Tube Assembly = 25.4 mm
Position: 847
Terminal-Spark Plug
Position: 851
Replacement MST-205-544C
Position: 900
02.16.05 TR
Position: 197465
Piston Assembly (.010” Oversize) 192 691986 Adjuster-Rocker Arm
Position: 697116
Piston Assembly (.020” Oversize) 202 691841 Link-Mechanical Governor
Position: 697117
Piston Assembly (.030” Oversize) 209 692208 Spring-Governor
Position: 697118
Ring Set (.010” Oversize) 222 694042 Bracket-Control
Position: 697119
Ring Set (.020” Oversize) 227 691374 Lever-Governor Control
Position: 697120
Ring Set (.030” Oversize) 231 691636 Screw (Choke Valve)
Position: 697121