Explosionszeichnung commande de vélo électrique HOMELITE Homelite 200
Entdecken Sie die vollständige Explosionszeichnung commande de vélo électrique HOMELITE Homelite 200 – ein unverzichtbarer Leitfaden zur Identifizierung aller Ersatzteile. Unsere Darstellung hilft Ihnen, jede Komponente Ihres commande de vélo électrique zu verstehen. Finden Sie schnell die benötigten Teile für Ihr commande de vélo électrique HOMELITE Homelite 200.
Reparatur-Assistent
Powered by ChatGPT
Ersatzteilliste
1 Repair Kit
Position: 1
2 SCREW- Hex hd. w/washer (8-32 x 1/2")
Position: 1
1 CYLINDER
Position: 1
1 CLIP- Retaining
Position: 2
1 SHIELD- Sawdust
Position: 2
1 TAPE
Position: 2
1 SCREEN- Spark arrestor
Position: 2
1 SCREW- Tapping (36-32 x 5/16")
Position: 3
1 DECAL
Position: 3
1 FILTER- Air
Position: 3
1 POST- Chain brake
Position: 4
4 SCREW- Pan, plastite (#10-16 x 3/4")
Position: 4
2 SCREW- Shoulder plastite (#10-24 x 1 3/4")
Position: 4
1 RING- Piston
Position: 5
1 COVER- Handle
Position: 5
1 BOX- Air filter
Position: 5
1 SCREW- Torx (10-24 x 5/8")
Position: 6
1 RING- Retaining
Position: 6
4 SCREW- Pan plastite (#6-3/8")
Position: 6
1 RING- Retaining
Position: 7
1 ROD- Throttle
Position: 7
2 SCREW- Torx taptite, thd. forming (10-24 x 1")
Position: 7
1 DECAL (International Only)
Position: 8
2 SEAL
Position: 8
1 COVER- Air filter
Position: 8
1 GASKET- Carburetor
Position: 8
1 SCREW- (10-32 x 1/2")
Position: 9
2 SPACER
Position: 9
2 BEARING- Needle
Position: 10
1 LOCK- Trigger
Position: 10
1 REED
Position: 10
2 WASHER- Thrust
Position: 11
1 STOP- Chain
Position: 11
1 STOP- Reed
Position: 11
1 WASHER- Flat
Position: 12
1 KEY
Position: 12
4 SCREW- Torx, taptite (#10-24 x 3/4")
Position: 12
2 SCREW- Hex Taptite (4-40 x 3/8")
Position: 12
1 SCREW- Drive
Position: 13
1 PRIMER BULB
Position: 13
1 GASKET- Intake manifold
Position: 13
1 NUT- Weld
Position: 14
1 FITTING
Position: 14
1 TUBING- Inlet (3")
Position: 14
1 DECAL- Handguard
Position: 15
1 BOLT- Guide bar, thd. forming
Position: 15
1 TUBING- Return (7")
Position: 15
4 SCREW- Torx pan hd. (10-24 x 1 1/8")
Position: 16
2 NUT- (5/16-24)
Position: 16
1 WEIGHT (International Only)
Position: 17
1 WASHER- (5/16")
Position: 17
1 BEARING
Position: 18
1 NUT- Hex
Position: 18
2 PIN- Roll (5/32 x 1 1/8")(Brake Mod. Only)
Position: 19
1 SHIELD- Muffler
Position: 19
1 LEAD- Hi-Tension
Position: 19
1 TUBING- Rubber (Oil line) (4 1/4")
Position: 20
1 HANDLE BAR
Position: 20
1 TUBING- (9")
Position: 22
3 SPRING- Clutch
Position: 22
1 TUBING (4 3/4")
Position: 23
1 SPIDER- Clutch
Position: 23
1 Oil Pump Body
Position: 24
1 VALVE- Check
Position: 25
1 FITTING- Oil line
Position: 26
1 BEARING
Position: 26
1 PIN- Adjusting
Position: 27
1 GASKET- Cap
Position: 28
1 E-RING
Position: 29
1 FILTER- Fuel
Position: 30
2 SCREW- Machine hex sems (#8-32 x 3/4")
Position: 30
1 LINE- Fuel (5 1/2")
Position: 31
1 SCREW- Machine hex sems (10-24 x 1 7/8")
Position: 31
2 WASHER- Thrust
Position: 32
1 FILTER
Position: 36
1 GRIP- Starter
Position: 37
6 SCREW- Torx, plastite (#10 x 3/4")
Position: 38
1 ROPE- Starter
Position: 40
1 WASHER- Retaining
Position: 42
1 SWITCH
Position: 43
1 Gasket/Diaphragm Kit
Position: 02769
1 Oil Pump Plunger Kit
Position: 02773
1 DECAL (International Only)
Position: 03271
18453 1 GREASE- Multi Purpose (Sprocket bearing-PT guide bar)
Position: 18453
22486 1 SHIM (0.015" AIR GAP)
Position: 22486
24823 1 SILASTIC (crankcase sealing)
Position: 24823
1 SPARK PLUG (Champion RDJ7Y) (International Only)
Position: 79252
2498201 1 T-25 TORX DRIVE BIT
Position: 2498201
7030999 1 OIL LINE- (10 ft. length)
Position: 7030999
7031099 1 FUEL LINE (10 ft. length)
Position: 7031099