Explosionszeichnung elt 2246 SNAPPER elt2246
Entdecken Sie die vollständige Explosionszeichnung elt 2246 SNAPPER elt2246 – ein unverzichtbarer Leitfaden zur Identifizierung aller Ersatzteile. Unsere Darstellung hilft Ihnen, jede Komponente Ihres elt 2246 zu verstehen. Finden Sie schnell die benötigten Teile für Ihr elt 2246 SNAPPER elt2246.
Reparatur-Assistent
Powered by ChatGPT
Ersatzteilliste
2 WHEEL & TIRE ASSEMBLY, Front
Position: 1
1 SEAT, Low Back (Used on 2690577 only)
Position: 1
1 SEAT, Hi Back, Steel Pan
Position: 1
1 CAP, Steering Wheel, Plain
Position: 1
1 PAD, Foot Pedal Reverse
Position: 1
1 CAPSCREW, Hex Head, Taptite, 5/16-18 x 3/4
Position: 1
*TRANSMISSION, Tuff Torq K46BP
Position: 1
* TRANSMISSION, Tuff Torq K46BL
Position: 1
1 DECAL, Height Of Cut
Position: 1
2 NUT, Push, 3/8
Position: 1
2 BOLT, Rear Wheel (42" Only)
Position: 1
3 NUT, Hex, Flange, 9/16-8
Position: 1
2 NUT, Hex Flange Center Locking, 3/8-16
Position: 1
1 CLIP, Pin, Safety
Position: 1
3 NUT, Hex Flange 9/16-18
Position: 1
1 DECAL, Snapper, LH Hood Stripe
Position: 1
1 DECAL, Snapper, LH Hood Stripe (Model 2690841 Only)
Position: 1
1 SWITCH ASSEMBLY, Ignition, 6-Pole (Includes Ref. 2, 3, 4 & 5)
Position: 1
1 TIRE, Turf 15 X 6.00 - 6 Saver TL
Position: 2
12 CAPSCREW, Whizlock, 1/4-20 x 5/8
Position: 2
4 WASHER, Plain, 5/16
Position: 2
1 NUT, Hex Lock, ESNA Light, 5/8-18, Thin
Position: 2
1 VALVE, Shut Off Oil Drain
Position: 2
1 BOLT, Carriage, 1/4-20 x 5/8 G5
Position: 2
1 ROD, Deflector
Position: 2
1 CAPSCREW, Hex Washer Head, Taptite, 3/8-16 x
Position: 2
2 WASHER, 1/2 (42" Only)
Position: 2
6 WASHER, Belleville
Position: 2
2 WASHER, Plain, 13/32 x 1-1/2 x 1/8
Position: 2
3 PULLEY
Position: 2
1 DECAL, Snapper, RH Hood Stripe
Position: 2
1 DECAL, Snapper, RH Hood Stripe (Model 2690841 Only)
Position: 2
1 WASHER, 5/8
Position: 2
1 TUBE, Tire, Front
Position: 3
1 DUCT, Air Inlet Plastic (Was 1731891)
Position: 3
1 LATCH, Seat 20GA E-Coat
Position: 3
1 WASHER, 5/8
Position: 3
2 SPACER, Pivot Powdered Metal
Position: 3
1 SEAL, Short
Position: 3
1 SEAL, Long (B&S Single)
Position: 3
1 ROD, Bypass, 11.44 LG
Position: 3
6 BOLT, Carriage, 5/16-18 x 3/4
Position: 3
1 WASHER, Plain, 13/32 x 1-1/2 x 1/8
Position: 3
2 WHEEL, Gauge (42" Only)
Position: 3
3 PULLEY, RH Arbor & LH Arbor, 4-1/4
Position: 3
2 NUT, ESNA, Lock, 1/2-13 (Thin)
Position: 3
1 HUB
Position: 3
1 DECAL, Ignition Switch Symbol, White/Black
Position: 3
1 LOCKWASHER, Internal Tooth, 5/8
Position: 3
1 WHEEL & BUSHINGS ASSEMBLY, Front
Position: 4
3 SCREW, Pan Head #10-24 x 1/2
Position: 4
4 CAPSCREW, Hex Head Flange Dog Point, 5/16-18 x
Position: 4
1 STEERING WHEEL, w/Aluminum Insert
Position: 4
2 PIN, Quick
Position: 4
1 NUT, Hex Flange Whiz, 1/4-20
Position: 4
11 NUT, Hex, Flange Whizlock, 5/16-18 (38" Only)
Position: 4
13 NUT, Hex, Flange Whizlock, 5/16-18 (42" Only)
Position: 4
2 HUB, Pulley, RH (Middle)
Position: 4
1 SPACER
Position: 4
2 SPACER
Position: 4
1 DECAL, Steering Wheel Icon
Position: 4
1 DECAL, Steering Wheel Icon (Model 2690841 Only)
Position: 4
1 NUT, Hex, Flange, 5/8-32
Position: 4
4 BEARING
Position: 5
2 PUSH NUT
Position: 5
4 SPACER, Powdered Metal Yellow
Position: 5
1 RING, Klipring Extension
Position: 5
4 SCREW, Hex Washer Head Taptite 5/16-18 x 5/8
Position: 5
1 NUT, Hex Flange, ESNA, 5/16-18
Position: 5
1 GRIP
Position: 5
1 SPRING, Torsion
Position: 5
1 SPACER, 0.387 ID x 1-1/2 OD x 1.04 LG Powdered Metal
Position: 5
2 NUT, Hex Flange, 5/16-18
Position: 5
3 SPACER
Position: 5
1 CAPSCREW, Hex Head, 3/8-16 x 2-1/2
Position: 5
1 PIN, Hitch
Position: 5
6 BEARING, Ball 11/16 x 9/16 x 15/32
Position: 5
1 DECAL, Height of Cut Not Used on 40" Mower
Position: 5
1 COVER, Ignition
Position: 5
1 FITTING, Grease, 1/4-28 Thread
Position: 6
1 KNOB, Cruise Lock Green Plastic
Position: 6
2 WASHER
Position: 6
6 NUT, Hex, Flange Whiz Lock, 5/16-18
Position: 6
1 ROD, Lift Handle E-Coat, 17.7 LG
Position: 6
6 NUT, Hex, Flange Whizlock, 5/16-18
Position: 6
1 CAPSCREW, Hex Head, 3/8-16 x 2-1/4
Position: 6
2 NUT, Hex Flange, 3/8-16 ESNA (42" Only)
Position: 6
1 CAPSCREW, Dog Point, SEMS, 1/4-20 x 3/4
Position: 6
1 ROD, Bail Mowers Yellow
Position: 6
3 SPACER, Powdered Metal
Position: 6
1 DECAL, Snapper Rear Stripe, Silver/ 8.5LG
Position: 6
1 DECAL, Snapper Rear (Model 2690841 Only)
Position: 6
1 IGNITION KEY (Set of 2)
Position: 6
2 VALVE STEM & CAP
Position: 7
1 COVER, Steering Shaft Plastic
Position: 7
2 BOLT, Carriage, 5/16-18 x 3/4
Position: 7
2 BUSHING, Steering
Position: 7
1 MUFFLER (B&S Twin)
Position: 7
VENT VALVE
Position: 7
1 DEFLECTOR & SUPPORT ASSEMBLY, Chute Riveted
Position: 7
4 WASHER, 3/8
Position: 7
11 BOLT, Carriage, 5/16-18 x 3/4 (38" Only)
Position: 7
13 BOLT, Carriage, 5/16-18 x 3/4 (42" Only)
Position: 7
1 CAPSCREW, Hex Head, 1/4-20 x 1/2
Position: 7
6 BEARING
Position: 7
1 PULLEY ASSEMBLY
Position: 7
3 GASKET
Position: 7
1 DECAL, Transmission Tow/ Release Lever
Position: 7
1 SWITCH, Headlights, 2 Terminal
Position: 7
8 WASHER, 3/4
Position: 8
4 WASHER, Flat, 3/4 x 1-1/4 (Model 2690841 & 2690865 Only)
Position: 8
2 CAPSCREW, Hex Head, Taptite, 5/16-18 x 3/4
Position: 8
1 ROD, Cruise Latch, 16.97LG (Was 1727898)
Position: 8
1 TRANSMISSION ASSEMBLY, K46BP
Position: 8
1 TRANSMISSION ASSEMBLY, K46BL (Used with 22" Tire Models)
Position: 8
MAGNET
Position: 8
1 WASHER, Plain, 21/64 x 1-1/4
Position: 8
2 IDLER, Flat
Position: 8
2 NUT, Hex Lock ESNA, 1/4-20
Position: 8
3 GASKET, Foam
Position: 8
1 SPACER
Position: 8
1 DECAL, Fuel Level
Position: 8
1 PLUG, Hole, Square
Position: 8
4 WASHER, Special Yellow
Position: 9
2 WASHER, Plain, 5/16
Position: 9
4 BOLT, Carriage, 5/16-18 x 3/4
Position: 9
2 CLIP, Linkage, Black
Position: 9
1 PIPE, Exhaust R.H. (B&S Twin)
Position: 9
4 SCREW, Hex Head Flange Lock, 5/16-18 x 2-1/2
Position: 9
1 SPRING, Torsion, 2.12 LG Black
Position: 9
2 PULLEY, 5.25 (38" Only)
Position: 9
2 PULLEY, 5.50 (42" Only)
Position: 9
2 PULLEY, 7.00 (42" Only) (CE/Export)
Position: 9
2 NUT, Hex, Flange Whizlock, 5/16-18
Position: 9
1 WASHER, 1/4
Position: 9
1 NUT, Whizlock, 3/8-16
Position: 9
2 CAPSCREW, Hex Head, Flange Whiz Lock, 5/16-18 x 3/4
Position: 9
26 SCREW, Hex Washer Head Taptite 5/16-18 x 3/4
Position: 9
1 DECAL, Tunnel
Position: 9
1 DECAL, Safety Instructions (CE/Export)
Position: 9
1 DECAL, Tunnel (France Models Only)
Position: 9
1 DECAL, Safety Instructions (Used only on ACS models)(CE/Export)
Position: 9
1 PLUG, Hour Meter (Kohler and B&S Single)
Position: 9
4 RING, Retaining
Position: 10
4 RING, Retaining, 3/4 (Model 2690841 & 2690865 Only)
Position: 10
1 KNOB, Brake Lock Plastic
Position: 10
4 NUT, Hex Flange, 5/16-18 ESNA
Position: 10
1 ROD, Parking Brake, 16.38 LG Yellow
Position: 10
1 PIPE, Exhaust L.H. (B&S Twin)
Position: 10
1 CAPSCREW, Hex Head, 3/8-16 X 1-3/4
Position: 10
2 CAPSCREW, Hex, 5/16-18 x 3/4
Position: 10
1 SPRING, Extension, Idler Arm (44” Mower Deck)
Position: 10
1 SPRING, Extension, Idler Arm (50” Mower Deck)
Position: 10
4 NUT, Hex Flange, 3/8-16 ESNA
Position: 10
1 DECAL, Belts,Blades (France Models Only)
Position: 10
1 DECAL, Belts, Blades
Position: 10
1 METER, Hour, LCD (B&S V-Twin Only)
Position: 10
4 CAP, Hub
Position: 11
4 CAP, Hub (Model 2690841 & 2690865 Only)
Position: 11
1 DASHBOARD
Position: 11
2 BOLT, Shoulder 5/16-18 G5
Position: 11
2 BOLT, Carriage, 3/8-16 x 1-1/4
Position: 11
1 SPACER
Position: 11
1 SPACER, Pivot Powdered Metal
Position: 11
2 BEARING, Upper
Position: 11
4 CAPSCREW, Hex Head, Flange Whiz Lock, 5/16-18 x 3/4
Position: 11
1 HUB, Adapter, LH
Position: 11
1 V BELT, Arbor Drive, 44”
Position: 11
1 V BELT, Arbor Drive, 44” (CE Only)
Position: 11
1 V-BELT, Arbor Drive, 50”
Position: 11
1 V-BELT, Arbor Drive, 50” Deck, 126.14" LG HA used on
Position: 11
4 WASHER, 1/2
Position: 11
1 WASHER, Plain, 1/4 (6 Total for Export)
Position: 11
2 KEY, 3/16 x 3/16 x
Position: 12
1 KEY, 3/16 x 3/16 x 2 (Model 2690841 & 2690865 Only)
Position: 12
1 GUIDE, Hood RH
Position: 12
2 SPRING, Compression
Position: 12
1 MUFFLER
Position: 12
1 V-BELT, Drive Belt, Aramid/Kevlar 89.25" EL HA
Position: 12
BYPASS SHAFT A
Position: 12
3 NUT, Hex, Flange Whizlock, 5/16-18
Position: 12
2 NUT, Hex Lock, ESNA Light, 5/8-18, Thin
Position: 12
2 NUT, Whizlock, 3/8-16
Position: 12
1 CAPSCREW, Hex Head, 3/8-16 x 1-1/4, G8
Position: 12
4 WHEEL, Gauge
Position: 12
2 CARRIAGE BOLT, 5/16-18 x 3/4 G5
Position: 12
1 DECAL, LT200 18.5HP
Position: 12
1 DECAL, LT200 20HP
Position: 12
1 DECAL, LT200 22HP
Position: 12
1 NUT, Wing, 1/4-20
Position: 12
2 WASHER
Position: 13
2 WASHER
Position: 13
4 WASHER, Spring Black
Position: 13
1 SPRING, Extension 07.52 LG Black
Position: 13
1 PIPE, Exhaust (B&S Single)
Position: 13
LEVER, Bypass
Position: 13
2 SPACER, Pulley, 38" Deck
Position: 13
1 SPRING, Extension 07.75 LG Black
Position: 13
1 PIN, Hitch
Position: 13
29 CAPSCREW, Hex Head, Taptite, 5/16-18 x 3/4
Position: 13
4 BOLT, Rear Wheel
Position: 13
1 DECAL, Danger, Chute in Place Not Used on 40" Mower
Position: 13
1 BOLT, Carriage, 1/4-20 x 7/8
Position: 13
2 SPACER, 0.77 ID x 1-1/4 OD x 1.65 LG Powdered Metal Black
Position: 14
2 RIVET, Pop, Stem Black
Position: 14
2 COVER, Spring
Position: 14
1 PULLEY, 3 OD Plastic
Position: 14
4 SCREW, Hex Washer Head Taptite 1/4-20 x 1/2
Position: 14
1 WASHER, Flat, 5/16
Position: 14
RING, Snap,
Position: 14
2 SCREW, Taptite, 5/16-18 x 5/8
Position: 14
2 RETAINING RING, Extension, 1-3/4
Position: 14
1 NUT, 3/8-16, Hex Flange MAC Locking Large, Black
Position: 14
2 SPACER, .532 ID x 3/4 OD x 1-1/4 LG Yellow
Position: 14
3 WASHER
Position: 14
3 NUT, Hex Flange 5/16-18, Whiz Lock Small
Position: 14
1 DECAL, Pinch Point Not Used on 40" Mower
Position: 14
1 NUT, Push On
Position: 14
2 WHEEL & TIRE ASSEMBLY, Rear 20"
Position: 15
2 WHEEL & TIRE ASSEMBLY, Rear 22"
Position: 15
1 GUIDE, Hood LH
Position: 15
1 POD, LH Cup Holder
Position: 15
1 SHAFT, Steering Gear & Spline Yellow
Position: 15
2 NUT, Hex Flange, 3/8-16 ESNA
Position: 15
1 CLIP, Speed Wire
Position: 15
1 CAPSCREW, Hex Head, 5/16-18 x
Position: 15
SEALING CAP
Position: 15
4 CLIP, Spring
Position: 15
10 SCREW, Hex, Washer Head, Taptite, 3/8-16 x 3/4
Position: 15
2 BOLT, Carriage, 5/16-18 x 3/4
Position: 15
2 NUT, ESNA, Lock, 1/2-13 (Thin)
Position: 15
1 SHAFT, Arbor
Position: 15
3 WASHER, Cup
Position: 15
1 DECAL, Danger, Hand Under Deck Not Used on 40" Mower
Position: 15
1 HOLD DOWN, Battery
Position: 15
1 TIRE, Turf 20 X 8.00 - 8 Saver TL
Position: 16
1 TIRE, Turf 22 X 10.00 - 8 Saver TL
Position: 16
12 NUT, Hex Flange Whiz, 1/4-20
Position: 16
1 ELBOW FITTING
Position: 16
1 BOLT, Carriage, 5/16-18 x
Position: 16
1 CONTROL, Throttle Double (B&S Single)
Position: 16
1 CONTROL, Throttle Double (B&S Twin)
Position: 16
1 CONTROL, Throttle, Choke-A-Matic (Models 2690841, 2690865 & 2690865-01 only)
Position: 16
RING, Snap, C
Position: 16
2 WASHER, 1/2
Position: 16
1 V-BELT, 91.10 LG Kevlar (Used on 38" Domestic Models)
Position: 16
1 V-BELT, 94.45 LG Kevlar (Used on 42" Domestic Models)
Position: 16
1 V-BELT, 91.10 LG A-Wedge Aramid (Used on 38" CE/Export Models)
Position: 16
1 V-BELT, 94.45 LG A-Wedge Aramid (Used on 42" CE/Export Models)
Position: 16
1 CLIP, Pin, Safety
Position: 16
3 SHIELD, Grass, Lower
Position: 16
1 SWITCH, Push Button (NC)
Position: 16
1 TUBE, Tire, Rear, 22 X 8 -
Position: 17
1 TUBE, Tire, Rear, 22 X 10 -
Position: 17
1 BUSHING
Position: 17
4 CAPSCREW, Hex Washer Head, Taptite, 5/6-18 x 5/8
Position: 17
1 PULLEY, Idler
Position: 17
2 CLAMP, Hose
Position: 17
1 WASHER, Plain, 5/16
Position: 17
SEAL WASHER
Position: 17
2 PIN, Threaded Shoulder
Position: 17
1 HOUSING, 42" (42" Only)
Position: 17
1 HOUSING, 38" (38" Only)
Position: 17
3 BLADE, 44”
Position: 17
3 SHIELD, Grass Lower Arbor, Heat Treated
Position: 17
1 DECAL, 38"
Position: 17
1 DECAL, 42"
Position: 17
1 DECAL, 44"
Position: 17
1 DECAL, 46"
Position: 17
1 DECAL, 50"
Position: 17
3 TIE, Self Locking 7-5/16
Position: 17
1 WHEEL, Hub
Position: 18
1 ROD, Dash Support
Position: 18
1 TANK, Fuel
Position: 18
1 SPRING, Extension
Position: 18
1 HOSE, Fuel
Position: 18
1 CAPSCREW, Hex Head, 5/16-18 x 1-3/4
Position: 18
1 FITTING, Grease
Position: 18
1 ROD, Bail Mowers Yellow
Position: 18
3 WASHER, Hex
Position: 18
3 BLADE, Mower 18.12" LG (Was 1708229)
Position: 18
1 DECAL, Hand Under Deck (CE/Export)
Position: 18
1 OUTLET, 12 Volt DC Power
Position: 18
4 WASHER, 3/4 x 1-7/8 (Model 2690841 & 2690865 Only)
Position: 19
1 SCREW, Taptite, 1/4-20 x 1/2
Position: 19
1 CAP, Gas
Position: 19
1 PIN, Cotter 3/32 x 3/4
Position: 19
2 CLIP, Hose
Position: 19
8 NUT, Hex, Flange Whizlock, 5/16-18
Position: 19
0-RING, 1A P10A
Position: 19
2 NUT, Hex, Flange, Whizlock, 5/16-18 x 1/2
Position: 19
1 SHAFT, Spindle, 38" Deck
Position: 19
3 WASHER, Spring
Position: 19
3 WASHER, Hex 11/16 x
Position: 19
1 PLUG, Hole Models W/O 12V Adapter
Position: 19
3 NUT, Hex, Nylon, Lock, #10-24
Position: 20
1 PAD, Footrest LH
Position: 20
1 ROD, Brake, 15.1 LG
Position: 20
3 SCREW, Hex Washer Head Taptite 3/8-16 x 1 (B&S Single)
Position: 20
SEAL TC
Position: 20
2 DECAL, CAUTION! Pinch Point
Position: 20
3 CAPSCREW, Hex Head, 7/16-14 x 1-1/4
Position: 20
1 SWITCH, Push Button (NO/NC)
Position: 20
4 NUT, Hex, Flange Whizlock, 5/16-18
Position: 21
1 SPRING, Extension 05.37 LG Black
Position: 21
1 LOCKWASHER, External Tooth 3/8
Position: 21
2 BOLT, Shoulder
Position: 21
4 WASHER, Belleville
Position: 21
2 BOLT, Carriage, 5/16-18 x 3/4
Position: 21
8 BOLT, Carriage, 5/16-18 x 3/4 (CE Only)
Position: 21
3 CAPSCREW, Hex Head 7/16-14 x 1-1/4 G8
Position: 21
1 PAD, Footrest RH
Position: 22
1 PEDAL, Brake Rubber
Position: 22
1 WASHER, 3/8
Position: 22
SCREW, Tapping, 8 *
Position: 22
2 NUT, Hex Flange, ESNA, 3/8-16
Position: 22
2 NUT, Hex 9/16-18
Position: 22
2 SHAFT, Arbor
Position: 22
4 SCREW, Taptite, 5/16-18 x 5/8
Position: 22
1 PIN, Quick
Position: 23
2 SPACER (Used on 38" & 42" Mower Decks)
Position: 23
2 SPACER (Used on 44" & 50" Mower Decks)
Position: 23
2 BLADE, Mower 38" (38" Only)
Position: 23
2 NUT, Hex, Flange Whizlock, 5/16-18
Position: 23
8 NUT, Hex, Flange Whizlock, 5/16-18
Position: 23
1 CARRIAGE BOLT, 1/4-20 x 1 G5
Position: 23
1 HEADLIGHT ASSEMBLY (Includes Ref. Nos. 24, 25, 26 & 27)
Position: 23
1 INSERT, Lightbar
Position: 24
6 SCREW, Hex, Washer Head, Plastite, 1/4-20 x 1/2
Position: 24
1 ROD, Brake Return, 12.60 LG
Position: 24
1 PULLEY & HUB ASSEMBLY, Engine
Position: 24
2 TRUNNION, Powdered Metal
Position: 24
2 WASHER, Spindle Blade Powdered Metal
Position: 24
1 COVER, Arbor
Position: 24
2 SOCKET ASSEMBLY
Position: 24
1 HEADLIGHT ASSEMBLY
Position: 25
6 SCREW, Taptite, 5/16-18 x 5/8
Position: 25
1 TIE, Self Locking
Position: 25
PIN, 3 * 9.8
Position: 25
PIN 3 * 9.8
Position: 25
2 ROD, Lower Lift, 10.00 LG
Position: 25
2 NUT, Push for 1/4 Diameter Thread
Position: 25
2 BULB, 1141-12V 21CP
Position: 25
2 POSITIONER, Hood
Position: 26
1 POD, RH Lift Quadrant
Position: 26
1 ROD, Cruise Latch, 2.83 LG
Position: 26
1 RETAINER, Clutch
Position: 26
2 SHAFT, Arbor, RH
Position: 26
4 WASHER, 1/4
Position: 26
1 REFLECTOR, Headlight
Position: 26
1 SPRING, Tension, Clutch
Position: 27
BOLT, 10 *
Position: 27
1 ROD, Lift, 5.43 LG
Position: 27
6 SCREW, Tapitite 1/4-20 x 1/2 (38" Only) (CE/Export)
Position: 27
2 CARRIAGE BOLT, 1/4-20 x 1, Black
Position: 27
1 CLAMP, Wire
Position: 27
1 LENS, Headlight
Position: 27
1 LATCH, Cruise Powdered Metal
Position: 28
1 CLUTCH, Electric OGURA
Position: 28
1 SPRING, Extension 5.10 LG Black (Used on 44" & 50" Mower Decks)
Position: 28
1 COVER, Arbor, RH
Position: 28
1 WASHER, 5/16
Position: 28
1 BOLT, Shoulder 5/16-18 G5
Position: 29
1 WASHER, Hex
Position: 29
IDS SPRING
Position: 29
2 NUT, Push On
Position: 29
1 SPRING, Torsion, Chute
Position: 29
1 NUT, Hex, Flange, 1/4-20
Position: 29
1 LOCKWASHER, Spring
Position: 30
4 LOCKWASHER, Interior Tooth 5/8 (42" Only) (CE/Export)
Position: 30
2 WASHER, Plain, 1/4 (6 Total for Export)
Position: 30
2 NUT, Hex Lock ESNA Light 1/4-20
Position: 30
1 COVER, Terminal
Position: 30
1 CAPSCREW, Hex Head 7/16-20 x 3-1/2 G5
Position: 31
1 CLAMP
Position: 31
1 DEFLECTOR
Position: 31
1 HARNESS, Wiring (Use on models with 12 Volt Outlet)
Position: 31
1 HARNESS, Wiring (Use on models without 12 Volt Outlet)
Position: 31
1 GASKET, Exhaust
Position: 32
SPRING
Position: 32
2 NUT, Hex Lock, ESNA, 1/4-20
Position: 32
1 ROD, Deflector
Position: 32
1 CABLE, Solenoid to Starter
Position: 32
2 SCREW, Hex Washer Head Taptite 3/8-16 x 1-1/4 (Qty. 1 used on 18.5HP)
Position: 33
PUMP SHAFT
Position: 33
1 WASHER, Flat, 5/16
Position: 33
2 HUB
Position: 33
1 SOLENOID
Position: 33
2 CAPSCREW, Hex Socket Head 5/16-18 x 3/4 G8
Position: 34
E-RING
Position: 34
7 RIVET, Pop (38" - France Only)
Position: 34
1 DEFLECTOR, Plastic
Position: 34
1 PLUG
Position: 34
2 SCREW, Taptite, 1/4-20 x 1/2
Position: 34
2 LOCKWASHER, Spring 5/16
Position: 35
BEARING, 6202C3
Position: 35
1 SPRING
Position: 35
2 LOCKWASHER, External Tooth, 5/16
Position: 35
MOTOR HOUSING
Position: 36
6 WASHER, Bellville
Position: 36
2 NUT, Hex, 5/16-24 NF
Position: 36
1 PAD, Foot Pedal Forward
Position: 37
2 PIVOT, Hood
Position: 37
1 SCREW, Hex Head Serange Flange Taptite 5/16-18 x
Position: 37
1 CABLE, #6 x 10 Long, with 2 Ring Terminals, Battery to Solenoid
Position: 37
2 BOLT, Carriage, 5/16-18 x
Position: 38
KIT, Cylinder Block
Position: 38
1 PLUG, Plastic (Not Shown)
Position: 38
1 CARRIAGE BOLT, 1/4-20 x 1-1/2 G5
Position: 38
2 NUT, Hex Flange Whizlock, 5/16-18
Position: 39
WASHER, 12 * 24 *
Position: 39
MOTOR SHAFT
Position: 40
RING, Snap, S15
Position: 41
1 BOOT, Insulator
Position: 41
BRAKE DISC/MOTOR GEAR (11T)
Position: 42
BRAKE DISC/MOTOR GEAR (10T)
Position: 42
1 BATTERY, 12 Volt, 230CCA
Position: 42
1 BATTERY, 12 Volt, 230CCA (CE/Export)
Position: 42
1 SWITCH, Push Button (NO), Reverse Pedal
Position: 43
THRUST METAL
Position: 44
2 NUT, Hex, Full, 1/4-20
Position: 44
2 LOCKWASHER, 1/4
Position: 45
THRUST BEARING K81105
Position: 46
2 WASHER, 1/4 I.D.
Position: 46
1 CABLE, Battery to Ground
Position: 47
2 CAPSCREW, Hex Head, 1/4-20 x 3/4
Position: 48
1 FUSE, Wiring Harness
Position: 49
1 SWITCH, RMO Module Only
Position: 50
1 KEY, w/Hang Tag for RMO Module
Position: 51
1 SWITCH, PTO, Push/Pull Symbols
Position: 52
CONTROL LEVER C
Position: 53
WASHER,
Position: 55
COTTER PIN, 1/8 * 3/4
Position: 56
SPRING PIN 6 *
Position: 57
ROLL PIN 6 *
Position: 58
O-RING 1A P14
Position: 59
NUT
Position: 60
WASHER, 12 * 32 * 3.2
Position: 65
REDUCTION GEAR (38T)
Position: 66
AXLE SHAFT, Left
Position: 68
AXLE SHAFT, Right
Position: 69
THRUST WASHER
Position: 70
RING
Position: 71
SEAL 19 * 32 *
Position: 72
BUSHING, 19 *
Position: 73
BRAKE SHOE
Position: 75
BRAKE LEVER
Position: 76
BRAKE ACTUATOR
Position: 79
SPRING PIN 5 *
Position: 80
O-RING 1A P12
Position: 81
SPRING PIN 4 *
Position: 82
PULLEY D
Position: 84
FAN, White
Position: 85
WASHER, Wave
Position: 86
SNAP RING
Position: 87
RING, Snap
Position: 87
OIL SEAL 16 * 22 * .03
Position: 91
K46 & T40 SEAL KIT (ALL MODELS)
Position: 200
38" Deck
Position: 1695146
38" Deck (French)
Position: 1695455
46" Deck
Position: 1695770
LT18538
Position: 2690577
LT2042
Position: 2690578
LT2044
Position: 2690579
LT2250
Position: 2690580
ELT18538
Position: 2690593
ELT2044
Position: 2690594
ELT18538
Position: 2690685
ELT2044
Position: 2690689
ELT2246
Position: 2690841
ELT18538
Position: 2690863
ELT18538F
Position: 2690864
ELT22
Position: 2690865
LT185
Position: 2690870
ELT185F
Position: 2690871