Explosionszeichnung lt 75175 SNAPPER lt75175
Entdecken Sie die vollständige Explosionszeichnung lt 75175 SNAPPER lt75175 – ein unverzichtbarer Leitfaden zur Identifizierung aller Ersatzteile. Unsere Darstellung hilft Ihnen, jede Komponente Ihres lt 75175 zu verstehen. Finden Sie schnell die benötigten Teile für Ihr lt 75175 SNAPPER lt75175.
Reparatur-Assistent
Powered by ChatGPT
Ersatzteilliste
2 REAR TIRE ASSY, 16X6.50-8
Position: 1
1 COVER, Steering Wheel
Position: 1
1 BATTERY CABLE, Negative, 17" - Black
Position: 1
1 DECAL, Operating Instructions
Position: 1
2 NUT, 5/16-18
Position: 1
1 BAGGER COVER
Position: 1
2 FRONT TIRE ASSY, 13X5.00-6
Position: 2
1 STEERING WHEEL
Position: 2
1 MUFFLER
Position: 2
2 WINGNUT, 1/4-20
Position: 2
1 DECAL, Nose, Snapper
Position: 2
1 DECAL, Parking Brake
Position: 2
1 BOLT, 5/16-18 x 2.0
Position: 2
4 HUB CAP
Position: 3
1 DASHBOARD
Position: 3
2 * GASKET
Position: 3
1 BOOT, Battery, Positive
Position: 3
2 DECAL, Snapper 15.5 HP (15.5HP Models Only)
Position: 3
2 DECAL, Snapper 17.5 HP (17.5HP Models Only)
Position: 3
1 DECAL, Ignition Switch
Position: 3
2 E-RING, .750D x .050T
Position: 4
1 SHAFT, Shaft
Position: 4
1 BATTERY CABLE, Positive, 12" - Red
Position: 4
1 DECAL, Stripe, LH
Position: 4
1 DECAL, Cutting Height
Position: 4
4 WASHER, FLAT 1.862 x .765
Position: 5
1 BELLOWS, Steering
Position: 5
1 HEAT SHIELD ASSEMBLY
Position: 5
1 DECAL, Stripe, RH
Position: 5
1 DECAL, Roll Release
Position: 5
1 BELT GUIDE
Position: 5
4 SCREW, Self Tap
Position: 5
2 WASHER, Flat, .81 x .550
Position: 6
1 BODY, Plastic
Position: 6
1 ELECTRIC CLUTCH
Position: 6
1 DECAL, Steering Wheel Insert
Position: 6
1 DECAL, Discharge Tube
Position: 6
4 WASHER, Flat, .75-1.3
Position: 7
1 FOOTREST SLEEVE
Position: 7
1 BATTERY COVER
Position: 7
1 IDLER STUD
Position: 7
2 Bolt, Carriage 1/4-20 x .63
Position: 7
1 DECAL, Bagger Cover
Position: 7
1 DECAL, Hot Surface
Position: 7
1 SPINDLE ASSY
Position: 7
2 PIN, Cotter 1/8" x 1-1/4"
Position: 8
1 FOOTREST, Plastic
Position: 8
2 CAPSCREW, 5/16-18 x 3/4
Position: 8
2 SCREW, 1/4-14 x 3/8
Position: 8
1 DECAL, Deck Width
Position: 8
1 DECAL, Throttle Control
Position: 8
19 BOLT, Carriage 5/16-18 x 5/8
Position: 8
1 IDLER PULLEY
Position: 8
2 CAPSCREW, 3/8-16 x 1 1/4
Position: 8
1 NUT, Hex Flange Lock, 5/16-18
Position: 9
1 WIRE HARNESS
Position: 9
1 DECAL, Fire Hazard
Position: 9
13 NUT, Hex Flange, 5/16-18
Position: 9
1 BLADE, 33"
Position: 9
2 NUT, 3/8-16
Position: 9
1 BEARING, Upper Steering
Position: 10
19 CAPSCREW, 5/16-18 x 3/4
Position: 10
4 BOLT, 3/8-16 x 1-1/4
Position: 10
1 SWITCH, Limit
Position: 10
1 DECAL, Sever Hazard
Position: 10
9 NUT, Hex Flange Centerlock 5/16-18
Position: 10
1 PULLEY, 33" Input
Position: 10
2 SCREW, Flat Head 10-3/4
Position: 10
2 SPRING, Seat
Position: 11
2 SCREW, Hex Head 5/16-18 x 5/8
Position: 11
3 TIE STRAP
Position: 11
1 DECAL, Brake/Clutch
Position: 11
2 NUT, Flange, 5/16-18
Position: 11
4 BOLT, Carriage, 5/16-18 x 5/8
Position: 12
1 CAPSCREW, Hex, 7/16-20 x 2-1/2, G5
Position: 12
1 SOLENOID, 3 Pole
Position: 12
1 DECAL, Speed Control
Position: 12
2 RING, Retaining
Position: 12
1 BAG
Position: 12
4 NUT, Hex Flange, 5/16-18
Position: 13
2 STACK PULLEY
Position: 13
3 NUT, Nylock 1/4-20
Position: 13
1 DECAL, Draw Bar Load
Position: 13
1 ROD DEFLECTOR
Position: 13
1 TOLERANCE RING
Position: 13
6 SCREW, Shoulder #10-24
Position: 14
1 BAFFLE, Engine
Position: 14
1 CABLE, Battery 8GA 18" - Red
Position: 14
2 ROD, Lift Link
Position: 14
2 WASHER, Spindle
Position: 14
1 SCREW, 1/4-20 x 1.25
Position: 14
2 BOLT, Shoulder 5/16-18 x 5/8
Position: 15
2 BOLT, Carriage, 1/4 - 20 x
Position: 15
2 SCREW, Shoulder #10-24
Position: 15
1 SWITCH, Ignition
Position: 15
2 ADJUSTING NUT
Position: 15
1 NUT, Hex Flange Lock, 1/4-20
Position: 15
1 GEAR, Pinion
Position: 16
4 NUT, Hex Flange Centerlock 5/16-18
Position: 16
4 NUT, Centerlock, 1/4-20
Position: 16
2 SCREW, Torx Head 5/16-18 x 5/8
Position: 16
1 NUT, Ignition Switch
Position: 16
1 LIFT ROD, Fixed
Position: 16
1 NUT, Flange 3/8-16
Position: 16
1 GRIP
Position: 16
2 ROLLER
Position: 17
2 WASHER, Flat, 3/4
Position: 17
5 SCREW, 5/16-18 x 1/2
Position: 17
1 LOCKWASHER, Spring 7/16
Position: 17
1 CAP, Ignition Switch
Position: 17
1 SPRING, Deflector
Position: 17
1 NUT, Hex, Jam, 3/4F GR8
Position: 17
2 COTTER PIN
Position: 17
1 BEARING, Lower Steering
Position: 18
4 SCREW, 5/16-18 x 0.50
Position: 18
3 PIN, Cotter
Position: 18
4 SCREW, Thread Forming, 1/4-20 x
Position: 18
1 KEY, Ignition
Position: 18
1 PUSH CAP
Position: 18
10 BOLT, Hex 3/8-16 x 3/4
Position: 18
1 SEAT
Position: 19
1 IDLER PULLEY, Backside
Position: 19
2 SWITCH, Seat
Position: 19
1 REAR DISCHARGE CHUTE
Position: 19
4 NUT, Hex Flange, 3/8-16
Position: 19
2 BOLT, Carriage, 3/8-16 x 5/8
Position: 19
2 BOLT, Shoulder, .31-18 x 1 1/4
Position: 20
4 BOLT, Shoulder, 5/16-18 x 1.50
Position: 20
1 NUT, Adjusting
Position: 20
1 SWITCH, PTO
Position: 20
1 CHUTE EXTENSION, Upper
Position: 20
6 NUT, Centerlock, 3/8-16
Position: 20
2 WASHER, 0.406 x 1 1/4
Position: 20
2 NUT, Hex Flange Centerlock 5/16-18
Position: 21
1 IDLER PULLEY, Fixed
Position: 21
1 NUT, Flange, 5/16-18
Position: 21
1 BUZZER, Bag Full Indicator
Position: 21
1 RUBBER STRAP
Position: 21
1 BELT, 33" Blade Drive
Position: 21
2 NUT, 5/16-18
Position: 21
1 WASHER, Flat, 1-1.3 16G
Position: 22
8 CAPSCREW, 5/16-18 x 3/4
Position: 22
1 * TRANSMISSION, Hydro Gear
Position: 22
1 SWITCH, BAG FULL
Position: 22
1 PIN
Position: 22
1 BAFFLE, Rubber
Position: 22
2 WASHER, .328 x 1.062 x .062 Z
Position: 23
6 SCREW, Hex 1/4-20 x 5/8
Position: 23
1 BAGGER SWITCH
Position: 23
1 BOLT, Carriage 1/4-20 x 5/8
Position: 23
2 NUT, Hex Jam, 1/2-20
Position: 23
1 SWITCH, Bag Full
Position: 23
2 BOLT, Hex Head, 5/16-24 x 2-3/4, G5
Position: 24
2 BOLT, Carriage 5/16-18 x 5/8
Position: 24
2 PIN, Threaded Shoulder, 3/8-16 x 1-1/2
Position: 24
2 WASHER, Flat, 5/16
Position: 24
1 FUSE, 15 Amp
Position: 24
2 WASHER, 1/2" Internal Tooth Lock
Position: 24
1 PIN
Position: 24
2 NUT, Centerlock 3/8-16
Position: 25
2 CLAMP, Hose, Yellow
Position: 25
2 NUT, Hex Flange 3/8-16
Position: 25
1 NUT, Hex Flange Lock, 1/4-20
Position: 25
1 HARNESS, Buzzer Connector
Position: 25
3 BOLT, Carriage, 5/16-18 x 3/4
Position: 25
1 NUT, Hex Center Lock Jam, 5/8-18
Position: 25
3 BOLT, Carriage, 1/4-20 x 5/8
Position: 25
2 NUT, 5/16-24
Position: 26
1 FUEL LINE
Position: 26
1 WASHER, 1.75 x 1.04 x 0.15
Position: 26
1 SERVICE KIT, Buzzer and Harness (Includes Ref Nos. 21 and 25)
Position: 26
1 WASHER, Flat, 5/16 x
Position: 26
2 NUT, Hex, 1/4-20
Position: 26
2 WASHER, Flat, .39-1. 14G
Position: 27
1 FUEL CAP
Position: 27
1 PEDAL, Clutch and Brake
Position: 27
4 BOLT, Shoulder, 3/8-16 x 1.10
Position: 27
6 SCREW, Oval Head, 5/16 - 24 x 21/32
Position: 27
13 CAPSCREW, 5/16-18 x 3/4
Position: 28
1 TANK, Fuel 1.6 Gallon.
Position: 28
1 ROD, Parking Brake
Position: 28
3 SCREW, 1/4-20 x 1/2
Position: 28
4 NUT, Hex Flange, 3/8-16
Position: 28
6 WASHER, 5/16" Internal Tooth Lock
Position: 28
1 E-RING, Retainer
Position: 29
1 KNOB, Parking Brake
Position: 29
1 MULCH COVER
Position: 29
6 NUT, Hex, 5/16 -
Position: 29
1 WASHER, .26 X.75 X 16GA
Position: 29
2 BUMPER, Rubber
Position: 30
2 BOLT, Carriage, 1/4-20 x 0.63
Position: 30
2 KEY, Square
Position: 30
4 SCREW, 10-24 x 1/2
Position: 30
6 WASHER, 1/2 x 7/8
Position: 30
1 NUT, Hex Flange 5/16-18
Position: 30
1 WINGNUT
Position: 30
1 SCREW, Thread Forming, 1/4-20 x
Position: 31
2 NUT, Keps Lock 1/4-20
Position: 31
1 NUT, Adjusting
Position: 31
1 HEAT SHIELD
Position: 31
2 WASHER, 1/2 x 1-1/2
Position: 31
1 HOLDER, Blade
Position: 31
2 SCREW, Self Tapping, 5/16-18 x 1.13
Position: 31
1 WASHER, Flat, .34, 1.20 11G
Position: 32
2 WASHER, Flat, .81 X .550 X 16GA
Position: 32
1 BOLT, Hex, 5/16-18 x 2-1/2
Position: 32
1 SCREEN, Spark Arrester, Flat
Position: 32
6 HAIRPIN
Position: 32
2 CAPSCREW, Hex Head, 1/2-20 x 1-1/4, GR5
Position: 32
1 WASHER, Flat 1.862 x .765 x 16GA
Position: 32
1 SCREW, Thread Forming, 10-16 x
Position: 33
1 RING, Foam
Position: 33
4 BOLT, Hex-Head 5/16-18 x
Position: 33
1 SCREEN, Spark Arrester, Formed
Position: 33
3 WHEELS, Anti Scalp
Position: 33
1 HAIRPIN
Position: 33
2 BOLT, Hex 3/8-16 x 1-1/2 G5
Position: 34
4 NUT, Flange Lock 1/4-20
Position: 34
3 CAPSCREW, Hex Head, 3/8-24 x 3/4, GR5
Position: 34
1 WASHER, 25/32 x 1.5 x .132
Position: 34
1 THROTTLE CONTROL
Position: 35
1 GRIP, Seat Adjustment Lever
Position: 35
3 NUT, Flange Lock, 3/8-16
Position: 35
3 SPACER, 3" Long
Position: 35
1 SPRING, Extension PTO
Position: 35
2 WASHER, .39-1.14
Position: 35
2 SCREW, Self Tap, #8 x 3/8
Position: 36
1 HEAT SHIELD (Used with Service Kit 885280 or After Serial No. 2013421413)
Position: 36
3 NUT, Hex Nyloc, 3/8-24
Position: 36
4 BOLT, Carriage, 3/8-16 x 5/8
Position: 36
1 LATCH, Spring
Position: 36
1 TINNERMAN CLIP
Position: 37
5 TAPE, Reflective
Position: 37
3 WASHER, Flat 3/8
Position: 37
1 DEFLECTOR, Chute
Position: 37
2 CAPSCREW, Hex Whiz Lock Flange, 5/16-18 x 3/4
Position: 37
1 FLOORMAT, RH
Position: 38
2 WASHER, .391 x 0.62 x.03
Position: 38
1 FLOORMAT, LH
Position: 39
4 WASHER, 0.641 x 1.38
Position: 39
1 BOLT, 1/4-20 x
Position: 39
3 PIN, Cotter, 3/4
Position: 40
1 NUT, Keps Lock 1/4-20
Position: 40
2 SCREW, 1/4 - 20 x 5/8
Position: 40
1 RETAINER, Spring
Position: 41
5 HAIR PIN, .56D-.092T
Position: 41
2 SCREW, Thread Forming, 10-24
Position: 42
1 BELT, Drive, 33"
Position: 42
3 CAPSCREW, Hex Whiz Lock, 5/16-18 x 3/4
Position: 42
2 CAPSCREW, Hex Head, 3/8-16 x 1-1/4
Position: 42
1 SPRING, Extension
Position: 43
2 NUT, 3/8-16
Position: 43
1 Spring, Brake Extension
Position: 44
4 NUT, Hex Flange Serrated, 5/16-18
Position: 45
2 BOLT, Carriage 1/4-20 x 5/8
Position: 46
1 PAD, Hydro Pedal
Position: 47
1 ROD, Shift Link
Position: 48
1 LEVER, Lift Deck
Position: 49
1 GRIP, .50 Black
Position: 50
1 PIN, Front Hanger
Position: 51
4 NUT, Hex Flange 5/16-18
Position: 52
1 ROD, Roll Release
Position: 53
1 ROD, Battery
Position: 54
1 ROD, Clutch Hydro
Position: 55
1 SCREW, Self Tap 5/16-18 x 7/8
Position: 56
1 SPRING, Extension
Position: 57
2 SPACER
Position: 58
6 WASHER, Flat, 1-1/4
Position: 59
1 PEDAL PAD, Hydro Reverse
Position: 60
1 SERVICE KIT, Lifter Assembly (Not Illustrated, Includes Ref. Nos. 8 and 49)
Position: 61
1 CAPSCREW, Hex, 1/4-20 x 9/16
Position: 63