Repair Assistant
Powered by ChatGPT
Spare Parts List
1 FUEL CAP, 3.25", MANAGED VENT, 16"TETHER
Position: 1
4 BODY CLIP, 1/4-20 X 1/2 DEEP
Position: 1
1 PULLEY-IDLER 04.00 OD 0.378ID 1.06 W BRG
Position: 1
10 NUT, 3/8-16 HEX NYLON LOCK
Position: 1
1 TRANSAXLE, ZT3400, LH, SHORT AXLE
Position: 1
1 GRIP, BLACK FLEXIBLE
Position: 1
2 SPACER, .52 X 1.00 X 2.09 - SS
Position: 1
2 TIRE ASSM, 11 X 4 - 5, FF / CB
Position: 1
1 DECAL, 36 (Models with 36" Mower Decks)
Position: 1
1 DECAL, CUT HEIGHT, SRS Z1
Position: 1
2 SPACER, .39 X 1.00 X .75, CZ
Position: 1
2 SPINDLE, ASSM, ALUMINUM - 5.25
Position: 1
1 PULLEY, 5.926OB X .985ID, SINGLE B-SEC
Position: 1
1 DECK SHELL W/DECALS, 48, SRSZ1 (5415014B)
Position: 1
1 PULLEY, FLAT IDLER, 6-3/4"
Position: 1
2 WHEEL- 2.00 WIDE 3.88 DIA 0.531ID POLY
Position: 1
1 DECK SHELL W/DECALS, Z148RDCE (5415509B)
Position: 1
1 ASSM, SPINDLE, LOW PROFILE (Nut and Washer Sold Seperately)
Position: 1
1 ASSM, SPINDLE, LONG SHAFT
Position: 1
1 BATTERY BOX, W/ DRAIN HOLE
Position: 1
4 BEARING, TAPERED ROLLER,
Position: 2
1 BOLT, CRANKSHAFT,7/16-20X2-3/4, GD8 (Models w/ Kawi Engines)
Position: 2
2 SPACER, IDLER ARM, 1/2, PM
Position: 2
2 BEARING, 1/2 FLANGED, PLASTIC BALL
Position: 2
1 TRANSAXLE, ZT3400, RH, SHORT AXLE
Position: 2
1 ROD, BRAKE CTRL, LOWER - LH
Position: 2
2 ROLLER, DECK HEIGHT
Position: 2
1 DECAL, 48 (Models with 48" Mower Decks)
Position: 2
1 DECAL, DASH PANEL, LH, CONTROLS
Position: 2
4 NUT, 5/16-18 HEX SERRATED FLANGE (SMALL)
Position: 2
5 BODY CLIP, 5/16-18-7GA MATERIAL
Position: 2
1 PULLEY, DOUBLE, 5.926 OVER BALL
Position: 2
3 PULLEY, B-SEC, 5.426OB, SPECIAL HUB
Position: 2
2 BOLT-WHEEL 3/8-16X2.781 .750 THRD
Position: 2
1 FITTING
Position: 2
1 FITTING, 1/8 NPT STR, SHORT (SV)
Position: 2
1 STRAP, RUBBER
Position: 2
2 SEAL, GREASE
Position: 3
2 NUT, 1/4-20 HEX NYLOCK FLANGE
Position: 3
1 CLUTCH, WARNER, 125 FTLBS - 1.13"
Position: 3
2 BEARING, BALL, AXLE
Position: 3
12 WASHER, 3/8 SAE
Position: 3
2 HYDRO RES. #71328, 350 ml
Position: 3
1 ROD, BRAKE CTRL, LOWER - RH
Position: 3
2 WASHER, FRICTION
Position: 3
2 WASHER, 1/2 SAE
Position: 3
1 DECAL, ICD CUTTING SYSTEM (Models with 48" Mower Decks)
Position: 3
1 DECAL, DASH PANEL, RH, WARNING/CONTROLS
Position: 3
1 DECAL, DASH PANEL, RH, WRNGS/CNTRLS, CE
Position: 3
2 WASHER, 5/16 SAE
Position: 3
2 WASHER, BLADE BOLT, 9/16" F436, CZ
Position: 3
2 BEARING, BRONZE FLANGE, 3/4"
Position: 3
1 SPACER, .52 X 1.75 X 2.25, CZ
Position: 3
2 SHIELD, TRASH
Position: 3
2 SHIELD, TRASH (SV)
Position: 3
2 NUT, 3/4-16, HEX JAM NYLON LOCK
Position: 4
2 WASHER, 1/4 SAE
Position: 4
1 MUFFLER, 15-19HP KAWI, CATALYTIC COMBUST (Models w/ Kawi FX600V
Position: 4
2 FITTING, 1/2 HOSE - 9/16 O-RING, 45 ELB
Position: 4
1 SPRING-COMP, .375IDX2.75LGX.054WR, SS
Position: 4
6 BUSHING, FLANGE Qty: 2 - Models w/ 48" Mower Decks
Position: 4
2 NUT, 1/2-13 HEX NYLOCK FLANGE
Position: 4
1 DECAL, FENDER, SRSZ1 / Z2, LH
Position: 4
1 DECAL, DANGER, STAND-ON
Position: 4
1 DECAL, WARNINGS, OPER COMPARTMENT, CE
Position: 4
1 CHUTE, RUBBER DISCHARGE CHUTE
Position: 4
2 NUT, 3/8-16 HEX SIDE LOCK
Position: 4
2 NUT, 3/8-16 HEX NYLON LOCK
Position: 4
2 BEARING, .98 X 2.44 X .67
Position: 4
2 BEARING, .98 X 2.44 X .67 (SV)
Position: 4
2 CAP, LOW PROFILE, STEEL
Position: 5
2 NUT, #10-24 HEX NYLON LOCK
Position: 5
1 CLAMP, VINYL INSULATED, 1.00
Position: 5
1 BELT, A-SEC, 50.5"EL, RAW EDGE, COG
Position: 5
4 CLAMP, HOSE, .75 FREE DIA.
Position: 5
1 SPRING-COMP, .496ID X 3.00LG X .112WR
Position: 5
4 ADJUSTER, DECK LIFT, CZ
Position: 5
2 CASTER AXLE DDSH
Position: 5
1 DECAL, FERRIS LOGO, SMALL
Position: 5
1 DECAL, SPANISH MANUAL, IGES, C-TICK
Position: 5
1 DECAL, CE DANGER
Position: 5
1 PULLEY-IDLER-V, 5.83OB X .51 ID BUSHING
Position: 5
1 DECK SHELL W/DECALS, Z136RDCE (5415982B)
Position: 5
1 FITTING, RELIEF, 1-5 PSI
Position: 5
1 HOUSING, SPINDLE (SV)
Position: 5
1 WIRE HARNESS, SRS CONSOLIDATED
Position: 5
4 WASHER, BELLEVILLE - 1.500 X .755
Position: 6
1 NUT, 3/8-24 HEX JAM
Position: 6
1 EYE BOLT, 3/8-16 X 6, 3THRD, 1EYE, CZ
Position: 6
1 PULL PIN, 3/8" DIA X 9/16" STROKE
Position: 6
4 WASHER, 1/4 SAE
Position: 6
2 ROD, HYDRO RELEASE, STAND ON
Position: 6
4 PIVOT, DECK LIFT TRUNION, GREASABLE
Position: 6
1 DECAL, FERRIS, 1.796 X 9.00
Position: 6
1 DECAL, HYDRAULIC OIL, 20W50
Position: 6
1 DECAL, HYDRAULIC OIL, 20W-50, 1" X 1.44"
Position: 6
2 SPACER, .52 X .74 X 1.50, CZ
Position: 6
10 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 6
4 SPACER, IDLER ARM, 1/2, PM
Position: 6
2 SPACER, .51 X .75 X .56, PM, CZ (USA Models Only)
Position: 6
1 HOUSING, SPINDLE
Position: 6
1 FITTING, RELIEF, 1-5 PSI (SV)
Position: 6
1 SWITCH, SEAT
Position: 6
1 WASHER, 3/8 SPLIT LOCK
Position: 7
1 PULLEY, CRANKSHAFT, 1.1255 ID X 4.00 OD (Models w/ Kawi Engines)
Position: 7
1 SPRING-EXT, 1.04 ODX6.935LGX.148WR, BLK
Position: 7
2 BEARING-FLANGE, 5/8
Position: 7
4 NUT, 1/4-20 HEX NYLOCK FLANGE
Position: 7
4 PIVOT BLOCK, PLASTIC
Position: 7
4 BEARING, RETAINER (SV)
Position: 7
2 DECAL, MODEL, Z1
Position: 7
2 DECAL, TRANSAXLE RELEASE, WB
Position: 7
2 SPACER, .328 X 1.0 X .85, CZ
Position: 7
6 BODY CLIP, 5/16-18-7GA MATERIAL
Position: 7
3 ASSM, SPINDLE, LONG SHAFT
Position: 7
2 SPACER, .38 X .50 X 2.50, CZ (USA Models Only)
Position: 7
1 SPACER
Position: 7
1 SPACER (SV)
Position: 7
1 MODULE, TIME DELAY, NO DIODE
Position: 7
1 CABLE, CHOKE CONTROL, 43.5"
Position: 8
1 HOSE, OIL DRAIN
Position: 8
1 SPACER, .52 X .84 X 1.53, PM
Position: 8
1 ROD, BRAKE, STAND-ON
Position: 8
8 NUT, 1/2-20, FOR WHEEL BOLT SILVER
Position: 8
1 DECAL, FENDER, SRSZ1 / Z2, RH
Position: 8
2 DECAL, WARNING, HAND IN BELT, ENG ONLY
Position: 8
1 DECAL, FIRE ANSI EXPORT
Position: 8
2 SPACER, .33 X .63 X .25, CZ
Position: 8
1 CHUTE, RUBBER DISCHARGE CHUTE (5104441)
Position: 8
4 BEARING, BALL, AXLE
Position: 8
2 NUT, 3/8-16 HEX NYLOCK FLANGE (USA Models Only)
Position: 8
1 SHAFT, SPINDLE
Position: 8
1 SHAFT, SPINDLE (SV)
Position: 8
1 WIRE HARNESS, JUMPER, KAWI (Models w/ Kawi Engines)
Position: 8
1 FUEL TANK, SRSZ1, 6 GAL
Position: 9
1 CABLE, THROTTLE, 40"
Position: 9
1 TIE,SELF-LOCKING, 24" (Qty: 2 - Models w/ B&S Engines)
Position: 9
1 SPACER, .39 X 1.00 X .50, PM, CZ
Position: 9
2 TIRE WHEEL ASM, 23 X 8.5-12, TURF MASTER (36" Deck Models)
Position: 9
2 DECAL, DANGER DO NOT OPERATE W/O DEFLECT
Position: 9
2 DECAL, DISCHARGE SAFETY, EXPORT
Position: 9
1 SHOCK / SPRING ASSEMBLY
Position: 9
1 CNSTR, CARB, 9 GAL
Position: 9
11 WASHER, 5/16 SAE
Position: 9
1 PULLEY, DEEP V-IDLER, 6.25"OD X 1/2"ID
Position: 9
2 WASHER, 3/8 SAE (USA Models Only)
Position: 9
1 SWITCH, PLUNGER, NO, SINGLE POLE SNAP-IN
Position: 9
2 PAD, FRICTION - 1.25 X 4.00
Position: 10
1 PTO SWITCH, MOMENTARY, SMALL KNOB
Position: 10
2 BELLEVILLE WASHER 1.1875 X .442 X .089
Position: 10
1 BUSHING, .38 X .88 X .73
Position: 10
1 PIN, HAIR, .0585 X 1-1/8, 1/4 EYE, CZ
Position: 10
2 RHSSNB, 3/8-16 X 2-1/4, GR5
Position: 10
1 SHAFT, UPPERBRAKE ROD SHORT, SRSZ1
Position: 10
2 TIRE WHEEL ASM, 23 x 10.5-12, TURF SMART (48" Deck Models)
Position: 10
2 DECAL, PINCH POINT
Position: 10
2 DECAL, PINCH POINT, CE
Position: 10
2 SPACER, STEP, .39 X 1.00 X .69, CZ
Position: 10
2 CLAMP, 3" ID, CUSHIONED, STAINLESS
Position: 10
2 SHIELD, PULLEY BEARING, CZ
Position: 10
2 WHEEL- 2.00 WIDE 3.88 DIA 0.531ID POLY (USA Models Only)
Position: 10
5 ROSEBUD LOOM CLIP
Position: 10
6 NUT, 5/16-18 HEX NYLOCK FLANGE
Position: 11
1 NUT, 5/16-18 HEX SERRATED FLANGE (LARGE)
Position: 11
1 ROD, 5/16-24 X 3.25, CZ
Position: 11
2 ROD, DECK LIFT TIMING, SRSZ1
Position: 11
1 DECAL, FIRE HAZARD, 3.25W X 3.0H
Position: 11
2 BUMPER, RUBBER
Position: 11
1 SPACER, .52 X 1.00 X .44, CZ
Position: 11
13 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 11
12 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 11
1 BATTERY CABLE, NEG, 22, 1/4-5/16
Position: 11
4 SCREW, 5/16-18X1, PHILLIPS HD. BZ
Position: 12
1 FITTING, 3/16" TEE, BARB TYPE, HDPE
Position: 12
1 RING, SWITCH RETAINER
Position: 12
1 NUT, 5/16-18 HEX NYLOCK FLANGE
Position: 12
1 NUT, 1/2-13 HEX NYLOCK FLANGE
Position: 12
1 CLEVIS, 5/16-24, STEEL, CLEAR ZINC
Position: 12
1 COLLAR, 1/2 SET
Position: 12
1 ROD, MAIN DECK LIFT, SRSZ1 (Models w/ 36" Mower Decks)
Position: 12
1 DECAL, BELT ROUTING, SRS-36 (36" Models)
Position: 12
1 KNEE PAD, SRS Z1, STAND ON
Position: 12
1 ROD, 5/16 X 13.75, TBE, CZ
Position: 12
1 SPACER, .52 X 1.00 X .22, CZ
Position: 12
3 WASHER, 3/4 BELLEVILLE CL/ZC
Position: 12
1 BATTERY CABLE, POS, 22, 1/4-5/16
Position: 12
9 WASHER, 3/8 SAE
Position: 13
1 FILTER, FUEL
Position: 13
1 SWITCH, IGNITION, 6 POST
Position: 13
3 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 13
5 WASHER, 5/16 SAE
Position: 13
1 NUT, 5/16-24 HEX
Position: 13
3 WASHER, 1/4 SAE
Position: 13
4 BALL JOINT, 1/2-20, RH, MALE, METAL RACE
Position: 13
1 DECAL, BELT ROUTING, SRS-48-52-61 (48" Models)
Position: 13
2 WASHER, 5/16 FENDER
Position: 13
1 SPACER, .52 X 1.00 X .63, CZ
Position: 13
3 NUT, 3/4-16 HEX
Position: 13
6 WASHER, 1/4 SAE
Position: 13
1 LEVER, HEAVY DUTY, THROTTLE CONTROL
Position: 14
1 GROMMET, 7/8"ID, 1/4" THICK STK
Position: 14
1 WASHER-3/8 FENDER
Position: 14
2 SPACER, .52 X 1.00 X .22, PM, CZ
Position: 14
2 TIE,SELF-LOCKING, 6"
Position: 14
8 WASHER, 5/16 SAE
Position: 14
1 SPRING, DECK, SRSZ1
Position: 14
9 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 15
1 BOLT, M8-1.25 X 16MM GD8.8 (Models w/ Kawi Engines)
Position: 15
2 BEARING, FLANGE
Position: 15
1 DECK SHELL W/DECALS, 36, SRSZ1 (5415399B)
Position: 15
1 SPACER, .390 X 1.00 X 1.00, CZ
Position: 15
3 WASHER, BLADE BOLT, 9/16" F436, CZ
Position: 15
2 GAUGE WHEEL-2.70
Position: 16
1 KEY, IGNITION, MOLDED SET
Position: 16
1 NUT, M8-1.25 SERR. FLANGE, CZ (Models w/ Kawi Engines)
Position: 16
2 SPACER, .38 X .50 X .27, CZ
Position: 16
1 BALL JOINT 5/16-24 LH FEMALE BRONZE RACE
Position: 16
4 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 16
2 NUT, 1/4-20 HEX SERR. FLANGE
Position: 16
1 COVER, PLASTIC SNAP ON
Position: 17
4 BOLT, 3/8-16 X 1-1/4, SF, PLT W/PATCH (Models w/ Kawi Engines)
Position: 17
1 BALL JOINT 5/16-24 LH FEMALE W/STUD, BR
Position: 17
1 WASHER, 5/16 USS
Position: 17
2 COLLAR, 5/16 SET
Position: 17
12 NUT, 1/4-20 HEX NYLOCK FLANGE
Position: 17
3 NUT, 1/2-13 HEX NYLOCK FLANGE
Position: 17
1 WASHER, 3/8 SAE
Position: 17
2 SPACER, .64 X 1.13 X .63, CZ
Position: 18
2 TIE,SELF-LOCKING, 6" (Qty: 1 - Briggs & Stratton Engines)
Position: 18
1 NUT, PLASTIC
Position: 18
1 ADAPTER-OIL DRAIN (Models w/ Kawi Engines)
Position: 18
1 WASHER, 3/8 GD.9 FLAT
Position: 18
2 GRIP, FOAM, .475 X 7.75 X .095
Position: 18
3 NUT, 5/16-18 HEX NYLOCK FLANGE
Position: 18
2 COLLAR, 1/4 SET
Position: 18
2 BUSHING, 1.00 X 1.13 X 1.38, PLASTIC Qty: 6 - Models with 48" Mower Decks
Position: 18
4 WASHER, 5/16 SAE (48" Mower Decks Only)
Position: 18
1 SPACER, .39 X .75 X .38, PM, CZ
Position: 18
1 FLAP, REAR DISCHARGE, UPPER
Position: 18
2 SCREW, #10-24 X 1 RS, CZ
Position: 18
2 SPACER, .38 X .63 X 3.25, CZ
Position: 19
1 GROMMET (SV)
Position: 19
2 WASHER, 3/8 SAE
Position: 19
1 ROD, 5/16-24 X 4.25, CZ
Position: 19
6 WASHER, 5/16 SAE
Position: 19
1 COLLAR, 5/16 SET
Position: 19
3 NUT, 1/2-13 HEX SIDE LOCK
Position: 19
4 NUT, 5/16-18 HEX NYLOCK FLANGE (48" Mower Decks Only)
Position: 19
1 EYEBOLT, 3/8-16 X 5, 2.88THRD, 1EYE, C
Position: 19
2 BOLT, 1/4-28 X 1/2, GD5 CZ
Position: 20
1 REMOTE VENT ASSY, NO VALVE (SV)
Position: 20
3 BALL JOINT 5/16-24 RH FEMALE BRONZE RACE
Position: 20
1 BEARING, 5/8" FLANGED, PLASTIC BALL
Position: 20
12 WASHER, 5/16 SAE
Position: 20
4 NUT, #10-24 HEX NYLON LOCK
Position: 20
2 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 21
9 NUT, 5/16-24 HEX
Position: 21
3 BEARING, 1/2 FLANGED, PLASTIC BALL
Position: 21
1 SPACER, .50 X .75 X .66, CZ
Position: 21
8 5/16 PUSH-ON NUT RETAINER, STL, CZ
Position: 21
1 GAUGE, FUEL LEVEL, 18.50" (SV)
Position: 22
1 WASHER, 1/4 SAE
Position: 22
1 NUT, 5/16-24 HEX, LH
Position: 22
1 PIN, HITCH, 3/8" DIA X 2.5" EL, CZ
Position: 22
2 WASHER-3/8 FENDER
Position: 22
1 WASHER, 1/2 GD9 CZ
Position: 22
25 NUT, 5/16-18 HEX NYLOCK FLANGE
Position: 22
1 ASM, PICKUP TUBE, FUEL TANK, 18.00" (SV)
Position: 23
1 NUT, 5/16-24 HEX NYLON LOCK
Position: 23
4 WASHER, .515 X 1.00 X .25", CZ
Position: 23
6 WASHER, 5/16 F436 FLAT
Position: 23
2 PLUG, PANEL, 1.25 - BLACK
Position: 23
1 NUT, 1/4-20 HEX NYLOCK FLANGE
Position: 24
2 ROD, MOTION CONTROL, STAND-ON
Position: 24
1 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 24
4 5/16 PUSH-ON NUT RETAINER, STL, CZ
Position: 24
4 WASHER, 5/16 SAE
Position: 25
2 CLAMP, HOSE, EXTERNAL, 1/2 - RED
Position: 25
8 WASHER, 1/4 SAE
Position: 25
1 CLEVIS, 1/2-20, STEEL, CLEAR ZINC
Position: 25
4 WASHER, 3/8 SAE
Position: 25
2 SPRING-EXT, .740 ODX2.025LGX.072WR, BLK
Position: 26
1 ROD, DECK LIFT LATCH
Position: 26
4 BODY CLIP, 5/16-18-7GA MATERIAL
Position: 27
2 WASHER, 5/16 SAE (Qty: 6 - Models w/ B&S Engines)
Position: 27
2 BALL JOINT 5/16-24 LH FEMALE BRONZE RACE
Position: 27
2 NUT, 5/16-24 HEX NYLON LOCK
Position: 27
1 SPRING-COMP 0.715ODX 03.85 LG
Position: 27
2 NUT, 1/2-20 HEX JAM
Position: 27
1 BELT, B-SEC, 115.29, ARAMID, WRAPED
Position: 27
2 FLAP, REAR DISCHARGE, LOWER
Position: 27
2 NUT, 7/16-14 HEX TOP LOCK
Position: 28
1 NUT, 1/4-20 HEX SIDE LOCK
Position: 28
4 COLLAR, DOUBLE SPLIT, 7MM
Position: 28
1 BUTTON, PUSH, DECK LIFT, THREADED
Position: 28
2 JOINT-BALL .500-20 THD .500ID, CLR ZINC
Position: 28
4 WASHER, 5/16 FENDER
Position: 28
2 CLAMP, VINYL INSULATED, 1.00
Position: 28
1 NUT, 3/8-16 HEX SIDE LOCK
Position: 29
2 NUT, 5/16-18 HEX SERRATED FLANGE (SMALL)
Position: 29
1 GRIP,LIFT LEVER
Position: 29
1 ROD, THREADED, 1/2-20 X 2.25
Position: 29
2 TIE, SELF-LOCKING, 12"
Position: 29
1 NUT, 3/8-16 HEX SERRATED FLANGE
Position: 30
1 MUFFLER, HOR, KAWASAKI (Models w/ Kawi FX691V Engine)
Position: 30
1 SCREW-HEX SEMS WSHR 1/4-20 X.88 DOG PT
Position: 30
3 WASHER, .390 X 1.50 X .109, CZ
Position: 30
2 5/16 PUSH-ON NUT RETAINER, STL, CZ
Position: 31
2 NUT, 5/16-18 HEX NYLOCK FLANGE
Position: 31
3 WASHER, 5/16 USS
Position: 31
3 BOLT, 3/8-16 X 3/4, PLT W/PATCH
Position: 31
1 BALL JOINT 5/16-24 RH FEMALE BRONZE RACE
Position: 31
4 BEARING, CUP
Position: 32
1 MUFFLER, 23HP BRIGGS VANGUARD, SRSZ1 (Models w/ B&S Engines)
Position: 32
1 SPACER, .33 X .50 X .25, PM, CZ
Position: 32
1 WASHER, 1/2 SAE
Position: 32
1 SPACER, 1.50 X 1.125 X .50, CZ (Models w/ B&S Engines)
Position: 33
2 BUMPER, RUBBER 1/4-20
Position: 33
1 PULLEY,CRANKSHAFT,1.1255IDX4.00OD,BRIGGS (Models w/ B&S Engines)
Position: 34
2 BEARING, BRONZE, FLANGED, 5/8", FLB10
Position: 34
7 NUT, 1/2-13 HEX NYLOCK FLANGE
Position: 34
1 BOLT, CRANKSHAFT, 7/16-20 X 3, GD8 (Models w/ B&S Engines)
Position: 35
5 GREASE FITTING, 1/4-28 STRAIGHT
Position: 35
2 WASHER, 5/16" SAE
Position: 35
2 NUT, 5/16-18 HEX NYLON LOCK
Position: 36
2 GREASE FITTING, 1/4-28, 90 DEGREE
Position: 36
6 WASHER, 5/16 USS
Position: 36
4 NUT, 5/16-24, TOP LOCK FLANGE, GD8 PHOS (Models w/ B&S Engines)
Position: 37
4 NUT, 5/16-18 HEX NYLOCK FLANGE
Position: 37
4 WASHER, 5/16 INT. TOOTH LOCK (Models w/ B&S Engines)
Position: 38
2 SCREW, TRUSS HD TORX DR5/16-18X0.875 BLK
Position: 38
1 PULLEY-V-IDLER, 5.830B X .38"ID
Position: 38
4 NUT, 3/8-16 HEX NYLON LOCK
Position: 39
1 SPACER, .52 X 1.00 X .50, CZ
Position: 39
1 SHIELD, PULLEY, 3/8"ID X 2"OD, CZ
Position: 40
1 BELT, B-SEC, 90.00"EL, ARAMID, WRAPED
Position: 41
1 PIN, SURE LOCK COTTER, .09 X .75, CZ
Position: 42
14 WASHER, 3/8 SAE
Position: 43
1 SPRING-EXT, 1.25 ODX5.70LGX.142WR, BLK
Position: 43
1 SPACER, .33 X .63 X .25, CZ
Position: 44
14 NUT, 3/8-16 HEX NYLOCK FLANGE
Position: 46
2 WASHER, 3/4 BELLEVILLE CL/ZC
Position: 47
2 NUT, 3/4-16 HEX
Position: 48
5 WASHER, 5/8 SAE
Position: 49
1 NUT, 1/2-13 HEX SIDE LOCK
Position: 49
2 WASHER, 1/2 USS
Position: 50
5 NUT, 1/2-20 HEX JAM
Position: 53
1 BELT, B-SEC, COGG, 56.875" EL
Position: 54
2 SPACER,3/8X3/4X15/16
Position: 56
2 CLEVIS, 5/16-18, 3/8 PIN HOLE, CLR ZINC
Position: 57
2 NUT, 5/16-18 HEX JAM
Position: 60
2 SPRING-EXTN 1.12 ODX 09.06 LG .177 ECOAT
Position: 61
2 SPACER, 1.02 X 1.56 X .50
Position: 62
1 ROD, MAIN DECK LIFT, 14.00 (Models w/ 48" Mower Decks)
Position: 64
Aubière Cedex
Position: 63178
SRS Z1 Series w/ 36" Mower Deck (SRSZ1KAV1936)
Position: 5901546
SRS Z1 Series w/ 48" Mower Deck (SRSZ1KAV2248)
Position: 5901547
SRS Z1 Series w/ 36" Mower Deck (SRSZ1BV2336)
Position: 5901550
SRS Z1 Series w/ 48" Mower Deck (SRSZ1BV2348)
Position: 5901675
SRS Z1 Series w/ 36" Rear Discharge Mower Deck (SRSZ1KAV1936RDCE)
Position: 5901676
SRS Z1 Series w/ 48" Rear Discharge Mower Deck (SRSZ1KAV2248RDCE)
Position: 5901677
SRS Z1 Series w/ 36" Mower Deck (SRSZ1KAV1936 CAL)
Position: 5901678
SRS Z1 Series w/ 48" Mower Deck (SRSZ1KAV2248 CAL)
Position: 5901687