Exploded view autoportee snapper SNAPPER sn17-84-snapper
Discover the complete exploded view autoportee snapper SNAPPER sn17-84-snapper, an essential guide to easily identify all spare parts of your appliance. Whether you are looking for a specific part or need help with the repair, our detailed presentation helps you understand each component of your autoportee snapper. Quickly find the parts you need to extend the life of your autoportee snapper SNAPPER sn17-84-snapper and avoid unexpected breakdowns.
Repair Assistant
Powered by ChatGPT
Spare Parts List
2 ASSEMBLY, Front Tire & Rim (Complete) (Includes Items 1A, 1B, 3, 4, & 5)
Position: 1
1 WELDMENT, Front Axle, Wide
Position: 1
1 WELDMENT, Main Case (Standard) (shown)
Position: 1
1 WELDMENT, Main Case (Commercial) (not shown) (used on Kohler Models only)
Position: 1
1 FENDER, Right Hand (1.62” Dia. Hole)
Position: 1
10 SCREW, 10-24 x 1/2” Hex Washer Self-Tap
Position: 1
1 SEAT, Operator (11.58” tall) (Michigan V-2400 Series)
Position: 1
1 REAR GUARD, Euro Maincase
Position: 1
1 DECK, 33” Replacement (painted deck w/decals)
Position: 1
1 NUT, 3/4-16 Hex Jam, GR
Position: 1
1 RAIL, Deck Lift, Left Hand
Position: 1
1 DECAL, SNAPPER
Position: 1
1 KIT, Battery, 12 Volt, 220CCA, Dry Charge (includes decal #7012358)
Position: 1
2 ASSEMBLY, Rear Tire & Rim (Includes Items 2A, 2B & 3)
Position: 2
1 ASSEMBLY, Steering Wheel (for 5/8” shaft) (Includes item 3)
Position: 2
1 FENDER, Left Hand (1.628” I. D. Hole)
Position: 2
1 GASKET, Transmission Case
Position: 2
1 ROLLER, 1-3/8 Long
Position: 2
1 SWITCH, Seat (NC)(Gray)
Position: 2
3 NUT, 1/4-20 Hex Flange Lock
Position: 2
1 * BELT, Drive (73.75” AA Section)
Position: 2
1 RAIL, Deck Lift, Right Hand
Position: 2
1 DECAL, Battery Storage
Position: 2
1 SOLENOID, Super-Trombetta (replaces 7018817)
Position: 2
1 SOLENOID, Super-Trombetta
Position: 2
1 VALVE STEM, Snap In
Position: 3
1 LOGO, Steering Wheel
Position: 3
2 HAIR PIN, 3/32 x 1-1/2”
Position: 3
1 RING, 1/2” External Retaining (Heavy Duty)
Position: 3
2 STRAP, Rear Guard
Position: 3
2 RING, 1.85” Internal Retaining
Position: 3
2 WASHER, 49/64” I.D. x 1-1/2” O.D. Flat
Position: 3
7 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
Position: 3
1 DECAL, Safety Instructions (French/German)
Position: 3
1 DECAL, Safety Instructions (English/Dutch)
Position: 3
1 DECAL, 8-Panel Symbols, Euro RER
Position: 3
1 DECAL, Safety Instructions (Spanish/Italian)
Position: 3
1 HARNESS, Starter Wiring (Kohler Engines)
Position: 3
1 HARNESS, Starter Wiring (Briggs, AC)
Position: 3
1 * LUBE Fitting, Straight (for 3/16” hole)
Position: 4
1 * LUBE Fitting, Straight (for 1/4” hole)
Position: 4
1 * LUBE Fitting, 90 Degree, Ball Check (for 1/4” hole)
Position: 4
1 * LUBE Fitting, 90 Degree, Ball Check (for 5/16” hole)
Position: 4
1 ROLL PIN, 1/4 x 1-1/2”
Position: 4
4 SCREW, 5/16-18 x 3/4” Hex Washer Self-Tap
Position: 4
10 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
Position: 4
1 WELDMENT, Primary Chain Case Half, Right Hand
Position: 4
4 BOLT, 5/16-18 x 1” Square Neck Carriage, GR 5 YZ
Position: 4
2 BOLT, 1/4-20 x 3/4” Short Neck Carriage, GR
Position: 4
2 BEARING, Spindle
Position: 4
1 PULLEY, Deck
Position: 4
1 DECAL, Deck Symbols- International
Position: 4
1 HARNESS, Ignition Wiring (15HP Kohler Engines)
Position: 4
1 HARNESS, Ignition Wiring (14.5 B&S)
Position: 4
2 BALL BEARING, Flange (3/4” I.D.)
Position: 5
1 FOAM COVER, Steering Shaft
Position: 5
2 SWIVEL, Adjustable, 5/16-18+.109 hole
Position: 5
2 SCREW, 1/4-20 x 5/8” Hex Washer Head Self-Tap (or 7090362)
Position: 5
2 BEARING, .625 x 1.37 x .435
Position: 5
8 RETAINER, 5/16” Bolt
Position: 5
3 PLUG, 1” Hole
Position: 5
1 ASSEMBLY, Housing (Incl. grease fitting, 7010817)
Position: 5
1 PULLEY, Hub (Powdered Metal)
Position: 5
1 ASSEMBLY, Clutch Plate
Position: 5
1 DECAL, Height of Cut
Position: 5
1 HOLDER, Fuse (Includes Fuse)
Position: 5
1 HOLDER, Fuse (Includes 7016169 10 AMP Fuse)
Position: 5
2 WASHER, .77 x 1.13 x .06 Flat
Position: 6
1 COVER, Steering Shaft
Position: 6
2 WING, Rear
Position: 6
1 BEARING, Axle (R. H. Fender) (used on Briggs model)
Position: 6
1 ASSEMBLY, Axle Bearing-DX (R. H. Fender) (incl. two DX Bearings, p/n 7074183) (used on
Position: 6
2 O-RING, 1/2 x 5/8”
Position: 6
4 BOLT, 5/16-18 x 1/2” Hex Flange Nyloc
Position: 6
1 GUARD, Main Case, Front, Euro RER
Position: 6
1 WASHER, 3/8” Flat SAE
Position: 6
1 SPRING, Latching
Position: 6
1 DECAL, 33 Inch (Hi-Vac)
Position: 6
1 INTERLOCK MODULE, Briggs & Kohler
Position: 6
1 INTERLOCK MODULE, Briggs
Position: 6
1 COTTER PIN, 5/32 x 1”
Position: 7
1 PIN, 3/16 x 1” Cotter
Position: 7
2 BOLT, 5/16-18 x 3/4” Hex Flange Lock, GR
Position: 7
1 WASHER, Thrust (1.37” ID, 1.625” OD)
Position: 7
1 WASHER, Shim .625 x .875
Position: 7
1 GUARD, Manifold, RER
Position: 7
2 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
Position: 7
1 SPINDLE, Rider (10.327” overall length)
Position: 7
1 BAND, Brake (Formed)
Position: 7
3 SCREW, 3/8-16 x 5/8” Hex Washer Self-Tap
Position: 7
1 DECAL, Battery Caution, Multi-Language
Position: 7
1 DECAL, Battery Orientation, Euro RER
Position: 7
1 HARNESS, (Deck Interlock Wiring)
Position: 7
1 HUB CAP
Position: 8
2 WASHER, .66 x 1.31 x .09 Flat
Position: 8
2 WASHER, 11/32” Flat
Position: 8
4 BOLT, 5/16-24 x 1-5/8” Hex Special Lock (Vibresist) (replace after each use)
Position: 8
1 KEY, #5 Woodruff
Position: 8
1 SCREW, 1/4-20 x 1” Hex Head Cap, GR
Position: 8
1 GUARD ASSEMBLY, Wire Form (Euro)
Position: 8
1 WASHER, .77 x 1.13 x .06 Flat
Position: 8
4 WASHER, .28 x .63 x .06 Flat, GR 5 (or 7090055)
Position: 8
2 SCREW, 5/16-18 x 1/2” Hex Washer Self-Tap
Position: 8
1 DECAL, Back-Up Recoil (33” Kohler Engine Models)
Position: 8
1 DECAL, OHV (33” Kohler Engine Models)
Position: 8
1 DECAL, Engine, B&S E10 Powerbuilt
Position: 8
1 FELT SEAL
Position: 9
1 BUSHING, Nylon
Position: 9
1 BUMPER, (1-Piece)
Position: 9
1 PLATE, Differential (Note: 4 holes offset - align properly to prevent binding.)
Position: 9
1 WELDMENT, Sprocket & Shaft
Position: 9
3 SCREW, 1/4-20 x 5/8” Hex Head w/Free Spinning Washer
Position: 9
2 SCREW, 3/8-16 x 3/4” Hex Washer Self-Tap, BZ
Position: 9
1 WASHER, Spindle
Position: 9
1 BUSHING, Flange .27 x .35 x .4
Position: 9
1 BRACE, Top
Position: 9
1 DECAL, Caution, Fuel Leakage (English)
Position: 9
1 DECAL, Caution, Fuel Leakage (Dutch)
Position: 9
1 DECAL, Caution, Fuel Leakage (French)
Position: 9
1 DECAL, Caution, Fuel Leakage (German)
Position: 9
1 DECAL, Caution, Fuel Leakage (Symbols)
Position: 9
1 DECAL, Caution, Fuel Leakage (Italian)
Position: 9
1 DECAL, Caution, Fuel Leakage (Spanish)
Position: 9
1 COVER, Battery Cable
Position: 9
1 CAP, Dust
Position: 10
1 HOLDER, Bottle (Wire)
Position: 10
4 SCREW, 3/8-16 x 5/8” Hex Washer Self-Tap
Position: 10
4, 8 SPACER, Pinion
Position: 10
2 WASHER, Thrust, Nylon
Position: 10
1 BRACKET, Muffler Guard (Kohler)
Position: 10
1 SCREW, 1/4-20 x 3/4” Hex Head Flange, GR 5, YZ
Position: 10
2 SCREW, 1/2-20 x 1-1/4” Hex Head Cap, GR
Position: 10
1 SPRING, Rectangular Wire Die, Blue
Position: 10
1 GUIDE, Belt
Position: 10
1 DECAL, Deflector, French/German
Position: 10
1 DECAL, Deflector Caution (English/Dutch)
Position: 10
1 DECAL, Blade Caution, Euro RER
Position: 10
1 WIRE, Positive (Red, 17” long)
Position: 10
1 TUBE, Inner (For 4.10/3.50 x 4 Tire)
Position: 11
2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap (Torx)
Position: 11
4 SCREW, 5/16-18 x 1-1/2” Hex Washer Self-Tap (or 7090484)
Position: 11
4, 8 GEAR, Differential Pinion (12T 12P)
Position: 11
2 BEARING, Needle 1.355” ID x 1.6245” OD x .5” Wide
Position: 11
1 MUFFLER GUARD, Kohler
Position: 11
2 SCREW, 1/4-20 x 1” Hex Washer Self-Tap
Position: 11
2 NUT, 1/2-20 Hex, GR 5 or B
Position: 11
1 NUT, 1/4-20 Hex Top Lock (or 7091705)
Position: 11
1 ANCHOR
Position: 11
1 DECAL, Brake Operation (German)
Position: 11
1 DECAL, Brake Operation (French)
Position: 11
1 DECAL, Brake Operation (Dutch)
Position: 11
1 DECAL, Brake Operation (Italian)
Position: 11
1 DECAL, Brake Operation (Spanish)
Position: 11
1 SWITCH, Ignition, 4 Terminal, Indak
Position: 11
1 SWITCH, Ignition-Afterfire Solenoid
Position: 11
3 BOLT, 1/2-20 x 3/4” Lug, GR
Position: 12
1 BOTTLE, Water
Position: 12
1 COVER, Battery
Position: 12
1 WELDMENT, Hub & Sprocket
Position: 12
1 HOLDER, Blade
Position: 12
1 PIN, 1/4 x 1-5/8” Clevis
Position: 12
2 WASHER, 5/16” Internal Tooth Lock
Position: 12
1 DECAL, Clutch Brake
Position: 12
1 WASHER, 5/8” Internal Tooth Lock
Position: 12
1 HUB CAP, R.H. (1.35” ID x 2.25”) (Short Axle)
Position: 13
1 COVER, Solenoid
Position: 13
1 ASSEMBLY, Short Axle, 23T (Includes Gear)
Position: 13
1 MUFFLER, (Kohler 14 & 15HP)
Position: 13
1 SPACER, Blade Centering
Position: 13
3 PIN, 3/32 x 3/4” Cotter (or 7090037)
Position: 13
2 NUT, 5/16-24 Hex (replaces 7090223 (voided))
Position: 13
1 DECAL, Euro Community (CE)
Position: 13
1 NUT, 5/8-32 Hex
Position: 13
1 HUB, Wheel LH, 3 Hole 3/4” ID (per left rear tire ass'y)
Position: 14
1 HAIR PIN 2-1/4”
Position: 14
7 FASTENER, 1/4” Ratchet
Position: 14
1 SPACER, Differential (1.25” ID x .423 Wide) (was 7011026)
Position: 14
1 GASKET, Primary Chain Case
Position: 14
3 SPACER, .33 x .63 x .156
Position: 14
1 NUT, 5/8-18 Hex Center Lock Jam
Position: 14
1 EYE-BOLT, 1/4-20 x 4”
Position: 14
2 SCREW, 5/16-24 x 3/4” Hex Head Cap, GR
Position: 14
1 DECAL, European Noise Control (100 dB)
Position: 14
1 DECAL, European Noise Control (98 dB)
Position: 14
1 IGNITION KEY, Pair
Position: 14
1 KEYS, Blister Pk (KIDS+MWRS DON'T MIX) English/French (set of two, one coated)
Position: 14
1 HUB, Wheel RH, 3 Hole 1” ID (per right rear tire ass'y)
Position: 15
1 SPRING, Parking Brake Latch
Position: 15
1 BRACKET, Belt Adjuster
Position: 15
1 KIT, Long Axle (Includes welded Gear and item #14) (was 7047763)
Position: 15
1 PRIMARY CHAIN CASE HALF, Left Hand
Position: 15
2 NUT, 1/4-20 Hex Flange Lock
Position: 15
2 SCREW, 1/4-20 x 3-1/2” Hex Head w/Free Spinning Washer
Position: 15
1 SPACER, .39 x 1.0 x .31 Nylon
Position: 15
2 SPRING, Assist
Position: 15
1 DECAL, No Mow in Reverse (Euro)
Position: 15
3 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
Position: 15
3 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap (or 7091122)
Position: 15
1 BOLT, 5/16-24 x 1-5/8” Tapered (Left Hand) (per left rear tire ass'y)
Position: 16
1 RING, 1/2” External Retaining (Heavy Duty)
Position: 16
1 TIE ROD, (5/16-24 thread- both ends)
Position: 16
1 WASHER, Thrust, (Hex Flanged)
Position: 16
2 WASHER, 5/8” Belleville
Position: 16
1 PLATE, Engine (Kohler Engine) (used on Kohler Engine Models only)
Position: 16
4 SCREW, 1/4-20 x 5/8” Hex Head w/Free Spinning Washer
Position: 16
1 DRUM, Brake Spindle (3” OD, 1.6” Tall)
Position: 16
1 BOLT, #10-24 x 1” Flat Head Square Neck
Position: 16
1 DECAL, Deck/Chute International Warning
Position: 16
1 CABLE TIE, 3.19” long
Position: 16
1 BOLT, 5/16-24 x 2” Tapered (Right Hand) (per right rear tire ass'y)
Position: 17
2 RING, 5/8” External Retaining
Position: 17
1 BUSHING, Pivot
Position: 17
1 * ASSEMBLY, Drive Hex Tube
Position: 17
1 PLUG, 3/4” Cup Insert
Position: 17
8 WASHER, .32 x .58 x .08 Split Lock
Position: 17
1 COVER, Spindle
Position: 17
2 RING, 2” External Retaining
Position: 17
1 NUT, #10-24 Hex Nyloc
Position: 17
1 DECAL, Service Parts, Euro
Position: 17
4 NUT, 1/4-20 Hex
Position: 17
1 HARNESS WIRE, Operator Presence Control (OPC)
Position: 17
1 NUT, Hex Lock 5/16F GR.C YZ (was 7011201 (per rear tire ass'y))
Position: 18
6 WASHER, .77 x 1.13 x .06 Flat
Position: 18
1 BRACKET, Switch
Position: 18
1 WASHER, Nylon
Position: 18
1 SCREW, 1/4-28 x 1” Hex Head Cap, (Washer Face) GR
Position: 18
4 NUT, 5/16-24 Hex, GR
Position: 18
1 PIN, Hinge
Position: 18
1 SPRING, Extension, 4” x 1/2” Diameter
Position: 18
2 RING, Rear Lift Arm (Blue)
Position: 18
1 DECAL, Remove Battery, Symbols, Euro
Position: 18
2 WASHER,1/4” Internal Tooth Lock
Position: 18
2 WASHER, 1/4” Internal Tooth Lock
Position: 18
1 HUB CAP, L. H. (.975” ID x 2.25”) (Long Axle) (per left rear tire ass'y)
Position: 19
4 BEARING, Nylon
Position: 19
2 SCREW, #10-32 x 1/4” Hex Washer Self-Tap
Position: 19
2 O-RING, 5/16”
Position: 19
2 WASHER, .28 x .63 x .06 Flat, GR
Position: 19
4 BOLT, M8-1.25 x 25mm, Self-Tap (Kohler)
Position: 19
3 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR 5 (or 7091510)
Position: 19
1 WELDMENT, Idler Arm
Position: 19
1 PIVOT, Leveling
Position: 19
2 SCREW, 1/4-20 x 5/8” Hex Head Cap, GR
Position: 19
2 SCREW, 1/4-20 x 5/8” Hex Head Cap GR 5 (or 7090072)
Position: 19
2 CLAMP, Boot, 2” (used on older models)
Position: 20
2 FOOT PAD, (Wide)
Position: 20
2 SCREW, 5/16-24 x 1” Hex Head Cap, GR
Position: 20
2 WASHER, 5/16” Belleville
Position: 20
1 SPACER, Brake Arm Pivot (.418/.403 long) (replaces 7010916 (.300/.285 long))
Position: 20
4 SCREW, 5/16-24 x 1” Hex Head Cap, GR
Position: 20
1 SPRING, Hinge
Position: 20
1 SCREW, 3/8-16 x 1-1/2” Hex Head Cap, GR
Position: 20
1 WIRE, Negative, Black (15” long)
Position: 20
1 SEAL, 1.22” ID x 1.875” OD (used on older models)
Position: 21
2 NUT, 5/16-24 Hex Center Lock
Position: 21
1 GEAR, 11 Tooth, 10 Pitch (replaces 7010964)
Position: 21
1 ASSEMBLY, Brake Lever (Includes brake pad & rivet)
Position: 21
1 BELT GUIDE, K 30/33” (used on all Kohler 33” Euro Models)
Position: 21
1 HINGE, Deflector (Deck side)
Position: 21
1 RESTRICTOR, Belt
Position: 21
1 NUT, 3/8-24 Hex Nyloc
Position: 21
1 HARNESS, Operator Presence Control (OPC) Wire
Position: 21
2 NUT, 1/4-20 Hex, GR 5 or B (attaches to starter terminal)
Position: 21
1 CAP, Seal 1.0” ID x 1.67” OD (used on older models)
Position: 22
1 PAD, Pedal
Position: 22
1 LIFT, Yoke
Position: 22
1 SPROCKET, 34T, 3/8P
Position: 22
1 RING, 3/8” External Retaining
Position: 22
4 SCREW, 5/16-24 x 1-3/4” Hex Head Cap, GR
Position: 22
2 PUSH NUT, 1/4”
Position: 22
2 PULLEY, Idler (3/8” ID, 4” OD)
Position: 22
1 WELDMENT, Rear Lift Arm
Position: 22
1 NUT, 1/4-20 Hex, GR 5 or B
Position: 22
1 SEAL, OIL .750” ID x 1.832” OD (used on older models)
Position: 23
1 CABLE, Clutch/Brake (55” long)
Position: 23
1 COLLAR, Yoke
Position: 23
1 RING, 1-3/16” External Retaining
Position: 23
1 * SPRING, Torsional Brake Return
Position: 23
2 NUT, 5/16-18 Hex Flange Lock, GR
Position: 23
9 NUT, 5/16-18 Hex Flange Lock, GR
Position: 23
2 WASHER, 3/8” Flat
Position: 23
2 ADJUSTER, Chain (5/16-18 thread)
Position: 23
2 CABLE TIE, 7”
Position: 23
1 CAP, Seal 3/4” ID x 1.875” OD (used on older models)
Position: 24
1 CABLE, Brake, Snap-In (replaces 7072648 (voided))
Position: 24
2 BEARING, Yoke
Position: 24
1 CHAIN, 46 Pitch (#35 Endless)
Position: 24
1 NUT, 1/4-28 Hex Top Lock
Position: 24
1 MUFFLER w/Guard (Briggs 17.5HP)
Position: 24
1 DEFLECTOR, Discharge, 28” & 33”
Position: 24
2 NUT, 3/8-16 Hex Nyloc
Position: 24
2 NUT, 1/4-20 Hex Center Lock, GR 5 or B
Position: 24
1 NUT, 1/4-20 Hex Center Lock, GR 5 or B
Position: 25
2 FENDER WASHER, 5/16”
Position: 25
1 SPACER, Differential Case
Position: 25
1 ASSEMBLY, Smooth Clutch (non-asbestos) (Includes the following 5 items)
Position: 25
1 SCREW, 1/4-20 x 5/8” Hex Washer Head Self-Tap
Position: 25
1 DECAL, Danger, (Cut Finger) International Symbol
Position: 25
1 SCREW, #10-32 x 1” Hex Washer Head Self-Tap
Position: 25
2 RETAINER, 1/4” Bolt
Position: 25
2 CONNECTOR, Cable
Position: 26
1 SPRING, Clutch & Brake
Position: 26
1 CASE, Transmission
Position: 26
1 HUB, Driven Disc (assembly) (replaces 7054243 (voided))
Position: 26
1 GASKET, Exhaust
Position: 26
2 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR 5 (or 7090001)
Position: 26
1 SWITCH, Deck Interlock (NO)
Position: 26
1 GRIP, Height Adjustment Lever
Position: 26
1 SCREW, 1/4-20 x 3/4” Hex Head Cap, GR
Position: 27
1 PIN, 3/32 x 3/4” Cotter (or 7090037)
Position: 27
2 PLUG, 1/2” Cup Insert
Position: 27
1 DISC, Driven (rubber tire bonded to rim)
Position: 27
1 ASSEMBLY, Oil Valve
Position: 27
2 WASHER, 5/16” Flat ( or 7091296)
Position: 27
1 MOUNT, Handle/Switch
Position: 27
1 LEVER, Height of Cut
Position: 27
1 SWITCH, Operator Presence Control (OPC) Traction (NC/NO)
Position: 27
1 TUBE CLAMP
Position: 28
2 WASHER, 3/8” Flat SAE
Position: 28
1 WASHER, 5/16” External Tooth Lock
Position: 28
1 WASHER, Thrust
Position: 28
2 SET SCREW, 5/16-18 x 3/4” Socket Head, GR8
Position: 28
2 NUT, 5/16-18 Wing
Position: 28
1 ROD, Idler Control
Position: 28
1 SPRING, Lever
Position: 28
1 SCREW, 5/16-24 x 2-1/2” Hex Head Cap, GR
Position: 29
1 BRACKET, Slide
Position: 29
1 WASHER, .34 x .69 x .08 Flat
Position: 29
1 PLATE, Drive Disc
Position: 29
1 ASSEMBLY, Fuel Tank with Gauge (Includes Cap)
Position: 29
2 BRACKET, Gage Wheel (Rear)
Position: 29
1 SPRING, Blade Handle
Position: 29
1 SCREW, 3/8-24 x 1-3/4” Hex Head Cap, GR
Position: 29
1 NUT, 5/16-24 Flange Lock (Large)
Position: 30
1 BOLT, 5/16-18 Shoulder
Position: 30
1 SCREW, 5/16-24 x 2-5/8” Hex Head Cap
Position: 30
4 NUT, 5/16-24 Hex Flange Lock
Position: 30
1 CAP, Fuel Tank w/Gage
Position: 30
3 SPACER
Position: 30
1 WELDMENT, Blade Engagement Handle
Position: 30
2 WASHER, 13/32 x 1-1/4” Flat
Position: 30
1 BUSHING, Nylon
Position: 31
2 SLIDE HALF
Position: 31
1 BOOT, Oil Seal (Short Axle)
Position: 31
1 NUT, 5/8-18 Hex Nyloc
Position: 31
4 CLAMP, Fuel Line (.490 X .31)
Position: 31
3 WHEEL, Gage
Position: 31
1 SPRING, Torsion, Flip Handle
Position: 31
2 SPACER, Deck Lift
Position: 31
1 WELDMENT, Steering Shaft
Position: 32
6 NUT, 5/16-18 Hex Flange Lock, GR
Position: 32
2 BOOT CLAMP, 2”
Position: 32
1 qt ** GREASE, Transmission (Use 2 oz. Maximum)
Position: 32
1 HOSE, Fuel (1/4” I.D. x 8-1/2” long) (used on 7800718 model)
Position: 32
1 HOSE, Fuel (1/4” I.D. x 12-1/2” long) (used on Kohler Models only)
Position: 32
1 HOSE, Fuel (1/4” I.D. x 6-1/2” long) (used on Kohler Models only)
Position: 32
3 SCREW, 3/8-24 x 3-3/4” Hex Head Cap, GR
Position: 32
1 PIN, 3/16 x 1” Clevis
Position: 32
1 NUT, 3/8-24 Hex Center Lock
Position: 32
1 PIN, 3/16 x 1-1/2” Cotter
Position: 33
1 BRACKET, Drive Support
Position: 33
1 GRIP, Shift Handle
Position: 33
1 HOSE, Fuel (1/4” I.D. x 3-1/2” long)
Position: 33
3 NUT, 3/8-24 Hex Nyloc
Position: 33
1 PIN, 3/32 x 1/2” Cotter
Position: 33
1 SPACER, Detent
Position: 33
4 WASHER, 3/8” Flat SAE (or 7091514)
Position: 34
1 WASHER, 5/16” Split Lock
Position: 34
1 WELDMENT, Shift Handle
Position: 34
1 VALVE, Fuel Shut-Off (Accessory)
Position: 34
1 BRACKET, Gage Wheel (Front)
Position: 34
1 HANDLE, Blade Engagement (Flip)
Position: 34
1 DETENT, Height Adjust
Position: 34
1 WELDMENT, King Pin, Left Hand
Position: 35
1 NUT, 5/16-18 Hex, GR 5 or B
Position: 35
1 PIN, 3/32 x 3/4” Cotter (or 7090037)
Position: 35
1 FILTER, Fuel (In-Line)
Position: 35
1 COVER, 33” Mulcher (optional)
Position: 35
1 GRIP, Handle
Position: 35
2 SCREW, 3/8-16 x 1” Hex Washer Self-Tap
Position: 35
1 WELDMENT, King Pin, Right Hand
Position: 36
1 STUD, Clutch Link (3/8-24 thread)
Position: 36
1 PIN, 1/4 x 1-3/4” Tapered Clevis
Position: 36
6 BOLT, 5/16-18 x 1/2” Short Neck Carriage, GR
Position: 36
2 SCREW, 1/4-20 x 5/8” Hex Washer Head Self-Tap (or 7091819)
Position: 36
1 CABLE ASSEMBLY, No Reverse in Mow
Position: 36
4 BUSHING, Tie Rod
Position: 37
1 ARM, Yoke
Position: 37
2 WASHER, Thrust (.76” ID, 1.63” OD)
Position: 37
2 SCREW, 5/16-18 x 1/2” Pan Head Self-Tap (Torx #T-40)
Position: 37
3 BOLT, 3/8-16 x 3/4” Hex Flange Lock
Position: 37
5 SCREW, 5/16-18 x 1/2” Hex Washer Self-Tap
Position: 37
1 RING, .438 External Retaining
Position: 37
1 TIE ROD, Left Hand (9.91” long)
Position: 38
1 WASHER, 3/8” Internal Tooth Lock
Position: 38
1 BUSHING, 3/4 x 1.62 Flange (Nylon)
Position: 38
4 WASHER, 11/32” Flat
Position: 38
2 NUT, 1/2-20 Hex Jam
Position: 38
1 BRACKET, Fixed Idler
Position: 38
2 RING, Front Lift Arm (Red)
Position: 38
1 TIE ROD, Right Hand (9.91” long)
Position: 39
1 NUT, 3/8-24 Hex, GR 5 or B (or 7090155)
Position: 39
1 NUT, 5/16-18 Hex Nyloc
Position: 39
1 PLATE, Throttle Control
Position: 39
2 WASHER, 1/2” Internal Tooth Lock
Position: 39
1 BRACE, Fixed Idler Bracket
Position: 39
1 WELDMENT, Front Lift Arm
Position: 39
2 PIN, 5/32 x 1” Cotter
Position: 40
1 ASSEMBLY, Leaf Spring
Position: 40
1 ** ASSEMBLY, Speed Adjustment Latch
Position: 40
1 CONTROL, Throttle (23.6” long) (Briggs Engines)
Position: 40
1 CONTROL, Throttle (34.6” long) (Kohler Engines)
Position: 40
1 RING, Tolerance
Position: 40
1 SPACER, Idler
Position: 40
1 PIN, 1/8 x 3/4” Cotter (or 7090365)
Position: 40
2 PIN, 1/8 x 3/4” Cotter
Position: 41
2 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
Position: 41
1 SPRING (part of Speed Adjustment Latch Ass'y)
Position: 41
9 NUT, 3/8-16 Hex Flange Lock (or 7090585)
Position: 41
1 GUARD, Pulley (used on 7800119)
Position: 41
1 ROD, Leveling (3/4-24 thread)
Position: 41
2 CAP, Dust
Position: 42
4 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap (or 7091867)
Position: 42
1 NUT, 5/16-18 Hex, GR 5 or B
Position: 42
2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap (Torx)
Position: 42
2 SCREW, 1/2-20 x 1” Hex Head Cap, GR
Position: 42
1 SCREW, 3/8-16 x 2” Hex Head Cap, GR
Position: 42
1 NUT, 3/8-24 Hex, GR B (or 7090155)
Position: 42
1 WASHER, 5/16” Internal Tooth Lock
Position: 43
1 SPRING, Shift Detent
Position: 43
1 WELDMENT, 5.25” O.D. Drive Disc
Position: 43
1 BLADE, 33”
Position: 43
1 WASHER, Flat 13/32” ID x 1.25” x 1/8” Thick ZP (or 7012063)
Position: 43
1 CLIP, Wire
Position: 44
1 BUSHING, 3/4 x I.O. Flange (Nylon)
Position: 44
2 SET SCREW, HRSS, 3/8-16 x 3/8”
Position: 44
1 BLADE, 33” Mulcher
Position: 44
1 ARM, Front Lift
Position: 44
3 NUT, 5/16-24 Flange Lock (Large)
Position: 45
1 WELDMENT, Arm, Shift Handle (w/grease fitting. Hole)
Position: 45
1 KEY, 1/4” Square x 2” Long
Position: 45
1 BLADE, Ninja, 33”
Position: 45
1 ROD, Deck Support (Front Lift Arm to Front End)
Position: 45
2 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR 5 (or 7090206)
Position: 46
1 LUBE FITTING, 3/16” Press-In
Position: 46
1 KIT, Air Lift, Hi-Vac (Includes items 47, 48, 49 & 50)
Position: 46
1 BOLT, Shoulder, 3/8-24 x 9/16”
Position: 46
2 BOOT CLAMP, 2”
Position: 47
1 WASHER, .32 x .58 x .08 Split Lock
Position: 47
2 NUT, 5/16-18 Hex Flange Top Lock
Position: 47
2 AIR LIFT, Hi-Vac (3 hole)
Position: 47
2 WASHER, 1/2” Flat SAE (or 7090250)
Position: 47
1 BOOT, Rear Axle, Thick Flange
Position: 48
1 NUT, 5/16-24 Hex, GR
Position: 48
2 KNOB, Fluted, 5/16-18 internal thread (2.15 O.D.)
Position: 48
6 SCREW, 5/16-24 x 11/16” Oval Head Machine
Position: 48
1 SPRING, Pedal
Position: 48
1 WASHER, Thrust, (Hex Flanged)
Position: 49
1 LEVER, Over-Ride
Position: 49
1 NUT, 1/4-20 Hex, GR 5 or B (not shown) (attaches to starter terminal)
Position: 49
6 WASHER, 5/16” Internal Tooth Lock
Position: 49
1 FOOT PEDAL, Blade Stop Control
Position: 49
1 WASHER, Thrust, (.765” ID, 1.625” OD)(Nylon)
Position: 50
1 WASHER, .47 x .92 x .065 Flat
Position: 50
6 NUT, 5/16-24 Hex
Position: 50
1 WASHER, Shim (Nylon, can make from 7011071) (or quantity as required)
Position: 51
1 BOLT, Shoulder, 5/16-18
Position: 51
1 NUT, 1/4-20 Hex Flange Lock, GR
Position: 51
1 CROSS BRACE
Position: 52
1 CLIP, Cable
Position: 52
1 WELDMENT, Shift Arm
Position: 53
1 BOLT, 1/4-20 x 3/4” Square Neck Carriage, GR
Position: 53
1 SHIFT LINK, Long (5/16-24 both ends)
Position: 54
1 BOLT, Shoulder, 3/8-24 w/Nylon Patch, GR
Position: 54
1 SHIFT LINK, Short (5/16-24 thread)
Position: 55
7 WASHER, .32 x .58 x .08 Split Lock
Position: 56
7 NUT, 5/16-24 Hex, GR
Position: 57
1 ASSEMBLY, DX Bearing (incl. items 59-61)
Position: 58
2 BEARING, DX, 3/4” ID
Position: 59
1 FITTING, Lube, 45 Degree, 3/16” w/Hex (long shank) (or 7013324)
Position: 60
1 SEAL, Axle (Dust/Grease)
Position: 61
1 KIT, Tire Chains (16 x 4.50-8 Tires) (used on All Rear Engine Riders)
Position: 7060049
1 KIT, Drive Disc Puller (used on All RER Aluminum Drive Discs)
Position: 7060325
1 KIT, Tire Chains (16 x 6.50-8 Tires) (used on All Rear Engine Riders)
Position: 7060653
1 KIT, Dump Cart (used on All Rear Engine Riders)
Position: 7060697
1 KIT, Gage Wheel (used on All 33” Deck Rear Engine Riders)
Position: 7060737
1 KIT, Single Bag Catcher (used on All 25” Deck Rear Engine Riders)
Position: 7060941
1 KIT, Single Bag Catcher (used on All 28” & 33” Deck Rear Engine Riders)
Position: 7060943
1 KIT, Bag-N-Wagon (used on All 28” & 33” Deck Rear Engine Riders)
Position: 7060947
1 KIT, 28” Thatcherizer (used on All series 7 & Newer Rear Engine Riders)
Position: 7060948
1 KIT, 36” Dozer Blade (used on All Rear Engine Riders)
Position: 7060959
1 KIT, Wagon Cover (used on All 28” & 33” Deck Rear Engine Riders)
Position: 7060964
1 KIT, Ninja Recycling Cover (used on All 25” Deck Rear Engine Riders)
Position: 7061049
1 KIT, Ninja Recycling Cover (used on All 28” Deck Rear Engine Riders)
Position: 7061253
1 KIT, Ninja Recycling Cover (used on All 33” Deck Rear Engine Riders)
Position: 7061255
1 HARDWARE BAG (Seat attachment & steering hdwe.) (used on model E281123BVE)
Position: 7061872
1 HARDWARE BAG (Seat attachment & steering hdwe.) (used on model E2512523BVE)
Position: 7063039
1 KIT, Twin Bag Catcher (used on All 28” & 33” Deck Rear Engine Riders)
Position: 7063281
1 HARDWARE BAG (Seat attachment & steering hdwe.) (used on models E2812523BVE,
Position: 7063292
1 KIT, Front Weight (used on All series 7 & Newer Rear Engine Riders)
Position: 7072416