Exploderad vy mrp 216518 b SNAPPER mrp216518b
Upptäck den fullständiga exploderade vyn mrp 216518 b SNAPPER mrp216518b – en oumbärlig guide för att identifiera reservdelar. Vår presentation hjälper dig förstå varje komponent i din mrp 216518 b. Hitta snabbt delarna till din mrp 216518 b SNAPPER mrp216518b.
Reparationsassistent
Powered by ChatGPT
Lista över reservdelar
1 HANDLE, Upper used on All
Position: 1
1 ASSEMBLY, Right Wheel Arm (Consists of items 2, 3, 4, 5A &
Position: 1
2 BALL BEARING, 9/16” I.D.
Position: 1
1 BELT, Poly-Vee
Position: 1
1 NUT, 5/16-24 Hex Lock
Position: 1
2 WHEEL, 8 x 1.75 Plastic
Position: 1
2 WHEEL, 10 x 1.75” Plastic (Push Models)
Position: 1
1 GRASS BAG, Slider Type (Black)
Position: 1
1 DECAL, Speed Sector
Position: 1
2 LATCH, Frame Attachment
Position: 1
1 SCREEN, Fastener Assembly
Position: 1
1 COVER, 21” Deck
Position: 1
1 PLUG, Chute Adapter
Position: 1
1 HANDLE, Middle used on All
Position: 2
10 NUT, 5/16-18 Hex Flange Lock, GR5
Position: 2
2 BOLT, 5/16-18 Hex Washer Face Shoulder
Position: 2
6 SCREW, #10-32 x 3/8” Hex Washer Self-Tap (Torx head)
Position: 2
1 LINK, Differential (Commercial)
Position: 2
1 WASHER, Bellville
Position: 2
2 PLUG, Wheel
Position: 2
2 WHEEL, 10 x 1.75” Plastic (Self-Propelled Models)
Position: 2
1 ADAPTER, Grass Bag
Position: 2
1 ASSEMBLY, Slider
Position: 2
1 DECAL, Speed Sector Int'l Symbol
Position: 2
1 RING, Bottom
Position: 2
1 BLADE, 21” Quad Edge Ninja
Position: 2
1 HANDLE, Lower LH (Adjustable) used on All
Position: 3
9 BOLT, 5/16-18 x 1/2” Short Neck Carriage GR5
Position: 3
2 LATCH, Height
Position: 3
2 LATCH, Height Adjusting (Long)
Position: 3
1 ARM, Clutch Idler
Position: 3
1 PULLEY, Poly-Vee Belt
Position: 3
2 NUT, 7/16-20 Hex Center Lock Jam
Position: 3
1 COVER, Bag Adapter
Position: 3
1 CONNECTOR, Grass Bag (weldment)
Position: 3
1 DECAL, Chute/Deflector
Position: 3
2 ROD, Tine
Position: 3
3 NUT, 5/16-24 Hex, GR5 only 1 shown
Position: 3
1 HANDLE, Lower RH (Adjustable) used on All
Position: 4
1 BOLT, 5/16-18 x 1-1/8” Short Neck Carriage GR5
Position: 4
2 GRIP, Height Latch
Position: 4
1 NUT, 1/4-20 Hex
Position: 4
1 PULLEY, Idler
Position: 4
2 WASHER, Spring
Position: 4
2 BUSHING, Axle
Position: 4
1 HINGE, Chute Cover
Position: 4
1 WIRE, Bag Adapter
Position: 4
1 DECAL, Ninja
Position: 4
1 SUPPORT, Wheel
Position: 4
3 WASHER, 5/16” Split Lock only 1 shown
Position: 4
1 BAIL, OPC Control used on All
Position: 5
3 SCREW, 3/8-16 x 1” Hex Washer Self-Tap
Position: 5
6 NUT, 5/16-18 Hex Flange Lock GR5
Position: 5
1 SCREW, 1/4-28 x 1-3/8” Hex Head Cap GR5
Position: 5
1 ASSY, Right Housing (Phantom) (Includes items 6, 7, 8, 9, 10 &
Position: 5
6 WASHER, 7/16” Flat Qty. of (2) for Push; Qty. of (1)
Position: 5
4 WASHER, 7/16” Flat
Position: 5
5 BOLT, 1/4-20 x 1/2” Short Neck Carriage GR5
Position: 5
1 ADAPTER, Bag
Position: 5
1 DECAL, SNAPPER
Position: 5
1 TRAY, Tine
Position: 5
3 SPRING only 1 shown
Position: 5
1 CLIP, Zone Control used on All
Position: 6
1 SCREW, 3/8-24 x 2” Hex Head Cap, GR5
Position: 6
2 RETAINER, 5/16” Bolt (Black)
Position: 6
1 ASSEMBLY, Wheel Arm, Right Rear (Round hole) used on Push models (Incl.
Position: 6
1 NUT, 1/4-28 Hex Top Lock
Position: 6
1 HOUSING, Right Side
Position: 6
5 WASHER, 1/4” Internal Tooth Lock
Position: 6
1 ASSEMBLY, Grass Bag Adapter (Includes items 7 thru 14)
Position: 6
1 DECAL, Warning (Deck)
Position: 6
6 KIT, Tine Thatching Spring
Position: 6
1 CABLE, Blade Control (46.75/5.38 length) used on All
Position: 7
2 WASHER, Cone
Position: 7
2 NUT, 5/16-18 Hex Flange Lock GR5
Position: 7
1 ASSEMBLY, Wheel Arm, Left Rear (Square hole) used on Push models (Incl.
Position: 7
2 BUSHING, 3/8” Plastic
Position: 7
3 SCREW, 5/16-24 x 1-1/8” Rib Neck, GR5
Position: 7
5 NUT, 1/4-20 Hex
Position: 7
1 ADAPTER, Bag
Position: 7
1 DECAL, Danger, Cut Finger
Position: 7
1 BUSHING, Wheel Adjuster
Position: 7
1 HANDLE, Wheel Drive used on Self Propelled
Position: 8
1 BLADE, 21” Ninja
Position: 8
1 WELDMENT, Front Wheel Bracket
Position: 8
1 ASSEMBLY, Wheel Arm, Right Rear used on Self-Propelled models
Position: 8
1 SHAFT, Hex Drive
Position: 8
1 SEAL, 5/8” Internal Diameter
Position: 8
1 STOP, Cover
Position: 8
1 BRACKET, Rope Pulley
Position: 8
1 DECAL, Warning (Euro)
Position: 8
1 AXLE, Wheel
Position: 8
1 GRIP,Wheel Drive Handle (International Symbol) used on Self Propelled
Position: 9
1 HUB, Blade Drive 25mm
Position: 9
1 AXLE, 21” qty. 2 on Push models
Position: 9
1 ASSEMBLY, Wheel Arm, Left Rear used on Self-Propelled models
Position: 9
1 PULLEY, Poly-V, 2” O.D. Non-Commercial Models
Position: 9
1 BEARING, Tapered- (Differential Housing)
Position: 9
1 MOLDING, Trim
Position: 9
1 SCREW, 5/16-18 x 1-1/4” Pan Head Machine
Position: 9
1 DECAL, 2004 Year of Mfg.
Position: 9
1 WHEEL, 7.00 x 1.50 Gage
Position: 9
1 CABLE, Clutch Pull (Z-bend, 41.25” long) used on Self Propelled
Position: 10
1 KEY, Hi-Pro #HP506 (Briggs engine)
Position: 10
1 WHEEL ARM, R.H. Rear used on Push models
Position: 10
1 WASHER, 3/8” Flat
Position: 10
1 BALL BEARING, 7/16 I.D., 1/1/8” O.D.
Position: 10
1 BUSHING, Flange
Position: 10
1 DECAL,Euro Community (CE)
Position: 10
10 NUT, 1/4-20 Hex Top Lock only 9 shown
Position: 10
1 COVER, Vinyl used on Self Propelled
Position: 11
1 SCREW, 5/16-18 x 5/16” Hex Socket Head
Position: 11
1 WHEEL ARM, L.H. Rear used on Push models
Position: 11
1 SPRING, Idler, Torsion
Position: 11
1 PLUG, Transmission
Position: 11
1 SPACER, .316 I.D. x .375 O.D. x .310 thick
Position: 11
1 PULLEY, Plastic
Position: 11
1 DECAL, Spart Plug International Symbol
Position: 11
4 WASHER, 1/4” Flat
Position: 11
1 SPRING, Clutch used on Self Propelled
Position: 12
1 PULLEY, Engine Drive (25mm x 2-1/8” O.D.)
Position: 12
1 ARM, Wheel, Right Rear used on Self-Propelled models
Position: 12
1 STUD, Idler (3/8-24 thread)
Position: 12
1 GEAR, Input
Position: 12
1 NUT, 5/16-18 Hex Large Flange Center Lock
Position: 12
1 NUT, 5/16-18 Hex Flange Lock GR5
Position: 12
1 DECAL, Caution, Symbols
Position: 12
2 SPRING, Compression
Position: 12
1 SECTOR, Speed '77VP used on Self Propelled
Position: 13
1 BOLT, 5/16-18 x 2-1/4” Hex Flange Lock
Position: 13
1 ARM, Wheel, Left Rear used on Self-Propelled models
Position: 13
1 HOLDER, Half
Position: 13
1 ASSEMBLY, Short Axle
Position: 13
1 RETAINER, 5/16” Bolt
Position: 13
2 WASHER, 15/32” Flat
Position: 13
1 DECAL, OPEI Walk/Ride
Position: 13
2 BOLT, 1/4-20 x 1-1/4” Hex, GR5
Position: 13
2 WIRE TIE, 1.29” Long (Black) used on All
Position: 14
2 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR5
Position: 14
2 BOLT, 5/16-18 x 1” Shoulder
Position: 14
1 BALL BEARING, .38 I.D. Spherical O.D.
Position: 14
1 GEAR, Differential (46 tooth)
Position: 14
2 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR5
Position: 14
4 RIVET
Position: 14
1 DECAL, Noise (European)
Position: 14
2 NUT, 1/4-20 Hex, GR5
Position: 14
1 SPRING, Speed Control used on Self Propelled
Position: 15
1 RETAINER, 5/16” Bolt
Position: 15
2 RETAINER, 5/16” Bolt
Position: 15
1 O-RING
Position: 15
2 PLATE, 46T Gear
Position: 15
1 CHUTE, Side
Position: 15
1 DECAL, Warning
Position: 15
2 CAP, Vinyl
Position: 15
1 WASHER, 3/8” Flat used on Self Propelled
Position: 16
2 NUT, 5/16-18 Hex Large Flange Center Lock
Position: 16
1 NUT, 3/8-24 Hex Center Lock GR5 or B
Position: 16
2 WASHER, Thrust, 3/4” I.D.
Position: 16
2 WASHER, 5/16” Flat
Position: 16
2 DECAL, Deck/Chute International Warning
Position: 16
2 BOLT, 1/4-20 x 2-1/2” Square Neck Carriage only 1 shown
Position: 16
1 GRIP, Speed Control Handle used on Self Propelled
Position: 17
6 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
Position: 17
1 BRACKET, Right Rear Wheel
Position: 17
1 HOLDER, Half
Position: 17
4 SCREW, #10-32 x 1-1/2” Hex Head Cap GR5 only 1 shown
Position: 17
2 WING-NUT, 5/16-18 Nyloc
Position: 17
1 DECAL, OPC Bail (International Symbol)
Position: 17
6 BOLT, 5/16-18 x 1” Square Neck Carriage, GR5 only 1 shown
Position: 17
1 ANCHOR, Lever used on Self Propelled
Position: 18
1 WASHER, 7/16” Flat
Position: 18
1 BRACKET, Left Rear Wheel
Position: 18
1 CLIP, Transfer Rod 1/4” also shown on HANDLES AND
Position: 18
1 GASKET, Housing
Position: 18
1 COVER, 21” Deck
Position: 18
1 DECAL, Operator Safety
Position: 18
2 BOLT, 1/4-20 x 3/4” Square Neck Carriage, GR5
Position: 18
1 GUIDE, Lower V-Belt used on Self Propelled
Position: 19
1 DECAL, Caution, International Symbols used on Euro models
Position: 19
1 AXLE, 21” Rear axle on Push Models;
Position: 19
1 ROD, Transfer also shown on HANDLES AND
Position: 19
3 WASHER, 5/16” Internal/External Tooth Lock only 1 shown
Position: 19
1 DECAL, Patent Numbers not shown
Position: 19
6 WASHER, Reinforcing only 1 shown
Position: 19
2 HOLE PLUG, Polyethylene
Position: 20
1 GUARD, Rear Foot used on Push models
Position: 20
1 BELT, Engine Drive 3L (Stretch)
Position: 20
1 BRACKET, Differential
Position: 20
6 WASHER, 5/16” Split Lock only 1 shown
Position: 20
1 CLIP, Transfer Rod 1/4” used on Self Propelled
Position: 21
1 COVER, Belt used on MRP216518B &
Position: 21
1 GUARD, Rear Foot used on Self-Propelled models
Position: 21
1 THRUST PLATE, Short
Position: 21
4 SCREW, 1/4-20 x 1” Hex Washer Self-Tap only 1 shown
Position: 21
6 NUT, 5/16-18 Hex, GR5 only 1 shown
Position: 21
1 T-NUT, 5/16-18 used on Self Propelled
Position: 22
3 SPACER, .06 Blade Hub
Position: 22
1 RING, Split (Black) used on Self-Propelled models
Position: 22
2 RING, 5/8” External Retaining used on Self-Propelled models
Position: 22
1 SPACER, Axle Gear
Position: 22
2 NUT, 1/2” Push
Position: 22
1 BUSHING, Differential used on Self Propelled
Position: 23
1 FENDER WELDMENT used on Euro models
Position: 23
1 SUPPORT, Foot Guard used on Self-Propelled models
Position: 23
1 BALL BEARING, 3/4” I.D. used on Self-Propelled models
Position: 23
1 ASSEMBLY, Long Axle
Position: 23
4 BEARING, Nyliner
Position: 23
2 BOLT, 5/16-18 x 3/4” Hex Flange Lock GR5 used on All
Position: 24
3 PLUG, 5/16” Square Hole used on Push models; (only one
Position: 24
1 BOLT, 1/4-20 x 1/2” Short Neck Carriage GR5 used on Self-Propelled models
Position: 24
1 WASHER, 3/4” Shim
Position: 24
4 GEAR, Pinion (12 tooth)
Position: 24
1 SCREW, 5/16-18 x 1/4” Set
Position: 24
1 SCREW, 5/16-24 x 1” Hex Head Cap GR5 used on All
Position: 25
3 PLUG, 5/16” Round Hole qty. 3 on Push, qty. 2 on Self-
Position: 25
1 WASHER, 1/4” Internal Tooth Lock
Position: 25
1 SHIELD, Hex Shaft
Position: 25
4 SPACER, Pinion Gear
Position: 25
2 WASHER, 1/2” Flat
Position: 25
1 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR5 used on All
Position: 26
1 BUSHING, .388 x .625 x 1.62 used on Euro models
Position: 26
1 BALL JOINT, 1/4-28 also shown on HANDLES AND
Position: 26
4 SHAFT, Pinion
Position: 26
1 DECAL, Adjustment
Position: 26
8 NUT, 5/16-18 Hex Flange Lock, GR 5 used on All
Position: 27
2 WASHER, 7/16” Flat used on Euro models
Position: 27
1 NUT, 1/4-28 Hex also shown on HANDLES AND
Position: 27
4 NUT, #10-32 Hex Nyloc
Position: 27
1 DECAL, Thatcherizer
Position: 27
1 NUT, 5/16-24 Hex Center Lock GR5 used on Self Propelled
Position: 28
1 COVER, Belt- IP21S used on Euro models
Position: 28
1 LINK, Transfer also shown on HANDLES AND
Position: 28
1 ASSY, Left Housing (Phantom) (Includes items 8, 9 & 29)
Position: 28
1 CLIP, Cable/Wiring used on All
Position: 29
1 SCREW, 5/16-18 x 1/2” Hex Head Cap, GR5 used on Euro models
Position: 29
1 HOUSING, Left
Position: 29
4 SCREW, 5/16-18 x 1-7/8” Curved Head GR2 used on All
Position: 30
3 WASHER, 3/8” Internal Tooth Lock
Position: 30
3 GASKET, 5/8” O. D.
Position: 30
4 KNOB, 5/16-18 Wing (Black) used on All
Position: 31
1 WASHER, 3/8” Flat
Position: 31
3 SCREW, 1/4-20 x 1-1/2 Hex Head Cap GR5 qty 1 on push model
Position: 32
1 NUT, 3/8-24 Hex
Position: 32
3 WASHER, 1/4” Internal Tooth Lock qty 2 on push
Position: 33
1 NUT, 5/16-18 Hex, GR5
Position: 33
3 NUT, 1/4-20 Hex used on All
Position: 34
1 WASHER, 5/16” Split Lock
Position: 34
1 CABLE-TIE, 7” used on All
Position: 35
1 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR5
Position: 35
4 BUSHING, .27 x .35 x .4 Flange used on Self Propelled
Position: 36
1 CONNECTOR, Transfer Rod
Position: 36
1 PIN, Clutch Handle used on Self Propelled
Position: 37
1 WASHER, .28 x .63 x .06 Flat used on Euro Self-Propelled
Position: 37
1 PUSH-NUT, 1/4” (for handle pin) used on Self Propelled
Position: 38
1 BUSHING
Position: 38
1 DECAL, OPC Bail (International Symbol) used on All; see Decal page
Position: 39
1 SPRING, Wheel Drive
Position: 39
1 GUIDE, Rope (1/4-20 thread) used on All
Position: 40
1 GUIDE, Thrust Plate (3/8-24 thread)
Position: 40
1 FOAM GRIP, 15”, 21 SP used on All
Position: 41
1 RETAINER, 3/8” Bolt
Position: 41
1 DECAL, Speed Sector used on MRP216518B; see
Position: 42
1 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR5
Position: 42
1 DECAL, Speed Sector Int'l Symbol used on EMRP216518B; see
Position: 43
1 DISC, Driven (Cantilever)
Position: 43
1 NUT, 1/4-28 Hex GR5 or B used on All
Position: 44
4 WASHER, 5/16” Internal Tooth Lock used on All
Position: 45
1 CLAMP, 7/8” Double Cable used on Self Propelled
Position: 46
1 SPACER used on Commercial models
Position: 46
1 LEVER, Speed Control used on Self Propelled
Position: 47
1 SCREW, 5/16-18 x 1/2” Hex Head Cap, GR5
Position: 47
1 WASHER, 5/16” Internal Tooth Lock
Position: 48
1 WASHER, .44 x .78 x .025 Curved
Position: 49
1 PIN, 3/32 x 1/2” Cotter
Position: 50
2 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
Position: 51
3 BOLT, 5/16-18 x 1/2” Short Neck Carriage GR5
Position: 52
2 NUT, 5/16-18 Hex Flange Lock, GR
Position: 53
1 SPRING, Clutch
Position: 54
1 WASHER, 1/4” Internal Tooth Lock used on Euro Self-Propelled
Position: 55