Exploderad vy Fischer snm7v-2006-erp217019bv

Upptäck den fullständiga exploderade vyn Fischer snm7v-2006-erp217019bv – en oumbärlig guide för att identifiera reservdelar. Vår presentation hjälper dig förstå varje komponent i din . Hitta snabbt delarna till din Fischer snm7v-2006-erp217019bv.

Reparationsassistent Powered by ChatGPT

Lista över reservdelar

1 HANDLE, Upper
1 HANDLE, Upper
Position: 1
1 WELDMENT, Deck, 21” Non-Adjust Air finish: red painted but w/o decals
1 WELDMENT, Deck, 21” Non-Adjust Air finish: red painted but w/o decals
Position: 1
1 WELDMENT, Deck, 21”, S.P., HV, Core Model finish: red painted but w/o decals
1 WELDMENT, Deck, 21”, S.P., HV, Core Model finish: red painted but w/o decals
Position: 1
2 WHEEL, 8 x 1.75” Plastic
2 WHEEL, 8 x 1.75” Plastic
Position: 1
1 BELT, Poly-V
1 BELT, Poly-V
Position: 1
4 NUT, 5/16-18 Hex Lock or
4 NUT, 5/16-18 Hex Lock or
Position: 1
1 ASSEMBLY, Bag Adapter/Cover (Includes items 2 thru 9)
1 ASSEMBLY, Bag Adapter/Cover (Includes items 2 thru 9)
Position: 1
1 BAG ASSEMBLY (Door) includes items 2, 3 &
1 BAG ASSEMBLY (Door) includes items 2, 3 &
Position: 1
1 DECAL, Easy Speed, Control Panel
1 DECAL, Easy Speed, Control Panel
Position: 1
1 SCREEN, Fastener Assembly
1 SCREEN, Fastener Assembly
Position: 1
2 LATCH, Frame Attachment
2 LATCH, Frame Attachment
Position: 1
1 HANDLE, Middle
1 HANDLE, Middle
Position: 2
5 NUT, 5/16-18 Hex Flange Lock, GR
5 NUT, 5/16-18 Hex Flange Lock, GR
Position: 2
1 BOLT, 5/16-18 x 3/4” Hex Washer Face Shoulder per wheel arm assembly
1 BOLT, 5/16-18 x 3/4” Hex Washer Face Shoulder per wheel arm assembly
Position: 2
4 NUT, 7/16-20 Hex Center Lock Jam
4 NUT, 7/16-20 Hex Center Lock Jam
Position: 2
1 WASHER, 44 x .78 x .025 Curved
1 WASHER, 44 x .78 x .025 Curved
Position: 2
1 WASHER, Cone
1 WASHER, Cone
Position: 2
1 ADAPTER, Grass Bag Euro 21” see Grass Bag Accessory page
1 ADAPTER, Grass Bag Euro 21” see Grass Bag Accessory page
Position: 2
1 GRASS BAG (Door w/Gray Letters)
1 GRASS BAG (Door w/Gray Letters)
Position: 2
1 DECAL, SNAPPER, Steel Decks
1 DECAL, SNAPPER, Steel Decks
Position: 2
1 RING, Bottom (21.77” Inside Diameter)
1 RING, Bottom (21.77” Inside Diameter)
Position: 2
1 HANDLE, Lower LH (Adjustable)
1 HANDLE, Lower LH (Adjustable)
Position: 3
3 BOLT, 5/16-18 x 1/2”, Short Neck Carriage, GR
3 BOLT, 5/16-18 x 1/2”, Short Neck Carriage, GR
Position: 3
1 LATCH, Height per wheel arm assembly
1 LATCH, Height per wheel arm assembly
Position: 3
2 BUSHING, Axle
2 BUSHING, Axle
Position: 3
1 LINK, Differential
1 LINK, Differential
Position: 3
1 PULLEY, Poly-V Belt (3.5” O.D.)
1 PULLEY, Poly-V Belt (3.5” O.D.)
Position: 3
1 COVER, Bag Adapter
1 COVER, Bag Adapter
Position: 3
1 CONNECTOR, Grass Bag (weldment)
1 CONNECTOR, Grass Bag (weldment)
Position: 3
1 DECAL, 2006 Year of Mfg.
1 DECAL, 2006 Year of Mfg.
Position: 3
1 BLADE, 21” Quad Edge Ninja
1 BLADE, 21” Quad Edge Ninja
Position: 3
3 NUT, 5/16-24 Hex, GR5 only 1 shown
3 NUT, 5/16-24 Hex, GR5 only 1 shown
Position: 3
2 ROD, Tine
2 ROD, Tine
Position: 3
1 HANDLE, Lower RH (Adjustable)
1 HANDLE, Lower RH (Adjustable)
Position: 4
2 PLUG, Hole, Polyethylene
2 PLUG, Hole, Polyethylene
Position: 4
1 GRIP, Height Latch per wheel arm assembly
1 GRIP, Height Latch per wheel arm assembly
Position: 4
1 WASHER, 5/16” Internal Tooth Lock
1 WASHER, 5/16” Internal Tooth Lock
Position: 4
2 WASHER, 44 x .78 x .025 Curved
2 WASHER, 44 x .78 x .025 Curved
Position: 4
1 HINGE, Chute Cover
1 HINGE, Chute Cover
Position: 4
1 ASSEMBLY, Bag Wire (12” Wide)
1 ASSEMBLY, Bag Wire (12” Wide)
Position: 4
1 DECAL,Euro Community (CE)
1 DECAL,Euro Community (CE)
Position: 4
3 WASHER, 5/16” Split Lock only 1 shown
3 WASHER, 5/16” Split Lock only 1 shown
Position: 4
1 SUPPORT, Wheel
1 SUPPORT, Wheel
Position: 4
1 BAIL, OPC Control
1 BAIL, OPC Control
Position: 5
1 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR 5 or
1 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR 5 or
Position: 5
4 PLUG, Wheel
4 PLUG, Wheel
Position: 5
1 SCREW, 5/16-18 x 1/2” Pan Head Self-Tap (Torx)
1 SCREW, 5/16-18 x 1/2” Pan Head Self-Tap (Torx)
Position: 5
1 ASSEMBLY, Right Housing (Incl. items 6, 7, 8, 9, 10 & 30)
1 ASSEMBLY, Right Housing (Incl. items 6, 7, 8, 9, 10 & 30)
Position: 5
5 BOLT, 1/4-20 x 1/2” Short Neck Carriage, GR
5 BOLT, 1/4-20 x 1/2” Short Neck Carriage, GR
Position: 5
1 PLUG, Chute Adapter
1 PLUG, Chute Adapter
Position: 5
1 DECAL, Warning (Deck)
1 DECAL, Warning (Deck)
Position: 5
3 SPRING only 1 shown
3 SPRING only 1 shown
Position: 5
1 TRAY, Tine
1 TRAY, Tine
Position: 5
1 CLIP, Zone Control
1 CLIP, Zone Control
Position: 6
1 RETAINER, 5/16” Bolt
1 RETAINER, 5/16” Bolt
Position: 6
4 RETAINER, 5/16” Bolt
4 RETAINER, 5/16” Bolt
Position: 6
2 WHEEL, 10 x 1.75” Plastic
2 WHEEL, 10 x 1.75” Plastic
Position: 6
1 ASSEMBLY, Idler Arm, Bushing & Spacer
1 ASSEMBLY, Idler Arm, Bushing & Spacer
Position: 6
1 HOUSING, Right Side
1 HOUSING, Right Side
Position: 6
2 WASHER, 1/4” Internal Tooth Lock
2 WASHER, 1/4” Internal Tooth Lock
Position: 6
1 ADAPTER, Grass Bag Euro 21”
1 ADAPTER, Grass Bag Euro 21”
Position: 6
1 DECAL, Spart Plug International Symbol
1 DECAL, Spart Plug International Symbol
Position: 6
6 KIT, Tine Thatching Spring was
6 KIT, Tine Thatching Spring was
Position: 6
1 CABLE, Zone Control (52-63/64” Long)
1 CABLE, Zone Control (52-63/64” Long)
Position: 7
1 SCREW, 3/8-24 x 2” Hex Head Cap, GR
1 SCREW, 3/8-24 x 2” Hex Head Cap, GR
Position: 7
4 NUT, 5/16-18 Hex Flange Lock, GR 5 or
4 NUT, 5/16-18 Hex Flange Lock, GR 5 or
Position: 7
1 ARM, Clutch Idler
1 ARM, Clutch Idler
Position: 7
3 SCREW, 5/16-24 x 1-1/8” Rib Neck, GR
3 SCREW, 5/16-24 x 1-1/8” Rib Neck, GR
Position: 7
2 NUT, 1/4-20 Hex or
2 NUT, 1/4-20 Hex or
Position: 7
2 DECAL, Warning (Euro)
2 DECAL, Warning (Euro)
Position: 7
1 BUSHING, Wheel Adjuster
1 BUSHING, Wheel Adjuster
Position: 7
1 HANDLE, Clutch
1 HANDLE, Clutch
Position: 8
2 WASHER, Cone
2 WASHER, Cone
Position: 8
1 AXLE, 21”
1 AXLE, 21”
Position: 8
4 BUSHING, Flange, .381 x .625 x .62
4 BUSHING, Flange, .381 x .625 x .62
Position: 8
1 SEAL, 5/8” Internal Diameter
1 SEAL, 5/8” Internal Diameter
Position: 8
1 STOP, Cover
1 STOP, Cover
Position: 8
2 RETAINER, 5/16” Bolt
2 RETAINER, 5/16” Bolt
Position: 8
1 DECAL, Caution, Symbols
1 DECAL, Caution, Symbols
Position: 8
1 AXLE, Wheel
1 AXLE, Wheel
Position: 8
1 GRIP, International Symbol
1 GRIP, International Symbol
Position: 9
1 BLADE, 21” Air Lift
1 BLADE, 21” Air Lift
Position: 9
1 BEARING, 9/16” I.D. per Rear Wheel Arm
1 BEARING, 9/16” I.D. per Rear Wheel Arm
Position: 9
1 SPACER, Idler Arm
1 SPACER, Idler Arm
Position: 9
1 BEARING, Tapered- (Differential Housing)
1 BEARING, Tapered- (Differential Housing)
Position: 9
1 TRIM, Moulding
1 TRIM, Moulding
Position: 9
1 DECAL, Noise, 98 dB
1 DECAL, Noise, 98 dB
Position: 9
1 WHEEL, 7.00 x 1.50 Gage
1 WHEEL, 7.00 x 1.50 Gage
Position: 9
1 CABLE, Clutch Control (41-1/4” Long)
1 CABLE, Clutch Control (41-1/4” Long)
Position: 10
1 BLADE, 21” Ninja (Quad Edge) used on ERP2167519BV &
1 BLADE, 21” Ninja (Quad Edge) used on ERP2167519BV &
Position: 10
3 SCREW, #10-32 x 3/8” Hex washer Self-Tap per Rear Wheel Arm
3 SCREW, #10-32 x 3/8” Hex washer Self-Tap per Rear Wheel Arm
Position: 10
1 NUT, 1/4-28 Hex Top Lock
1 NUT, 1/4-28 Hex Top Lock
Position: 10
1 BALL BEARING, 7/16 I.D., 1/1/8” O.D. was
1 BALL BEARING, 7/16 I.D., 1/1/8” O.D. was
Position: 10
2 BOLT, 5/16-18 x 1-1/8” Short Neck Carriage, GR
2 BOLT, 5/16-18 x 1-1/8” Short Neck Carriage, GR
Position: 10
2 NUT, 5/16-18 Hex Large Flange Center Lock
2 NUT, 5/16-18 Hex Large Flange Center Lock
Position: 10
1 DECAL, Speed Shift
1 DECAL, Speed Shift
Position: 10
10 NUT, 1/4-20 Hex Top Lock was 7090761 (only 9 shown)
10 NUT, 1/4-20 Hex Top Lock was 7090761 (only 9 shown)
Position: 10
1 COVER, Vinyl
1 COVER, Vinyl
Position: 11
1 COVER, Belt
1 COVER, Belt
Position: 11
1 LATCH, Height Adjusting (long) per Rear Wheel Arm
1 LATCH, Height Adjusting (long) per Rear Wheel Arm
Position: 11
1 PULLEY, Idler, V21
1 PULLEY, Idler, V21
Position: 11
1 PLUG, Transmission Housing
1 PLUG, Transmission Housing
Position: 11
1 SPACER, .316 I.D. x .375 O.D. x .310 thick
1 SPACER, .316 I.D. x .375 O.D. x .310 thick
Position: 11
1 DECAL, Throttle Control, B&S
1 DECAL, Throttle Control, B&S
Position: 11
4 WASHER, 1/4” Flat was
4 WASHER, 1/4” Flat was
Position: 11
1 SPRING, Clutch- 21S
1 SPRING, Clutch- 21S
Position: 12
1 PULLEY, Engine (25mm I. D. x 2-1/8” O.D.)
1 PULLEY, Engine (25mm I. D. x 2-1/8” O.D.)
Position: 12
1 BOLT, 5/16-18 x 1” Hex Washer Face Shoulder per wheel arm assembly
1 BOLT, 5/16-18 x 1” Hex Washer Face Shoulder per wheel arm assembly
Position: 12
1 SCREW, 1/4-28 x 1-3/8” Hex Head Cap, GR
1 SCREW, 1/4-28 x 1-3/8” Hex Head Cap, GR
Position: 12
1 GEAR, Input
1 GEAR, Input
Position: 12
3 NUT, 5/16-18 Hex Large Flange Center Lock
3 NUT, 5/16-18 Hex Large Flange Center Lock
Position: 12
2 DECAL, Deck/Chute International Warning
2 DECAL, Deck/Chute International Warning
Position: 12
2 SPRING, Compression
2 SPRING, Compression
Position: 12
1 BRACKET, Shift
1 BRACKET, Shift
Position: 13
1 SCREW, 5/16-18 x 1/2” Hex Socket Head
1 SCREW, 5/16-18 x 1/2” Hex Socket Head
Position: 13
1 ASSY, Wheel Arm, Right Rear (S.P.) Incl. 4, 6, 9, 10, 11, 15 &
1 ASSY, Wheel Arm, Right Rear (S.P.) Incl. 4, 6, 9, 10, 11, 15 &
Position: 13
1 COTTER PIN, 3/32 x 1/2”
1 COTTER PIN, 3/32 x 1/2”
Position: 13
1 AXLE, Short
1 AXLE, Short
Position: 13
3 RETAINER, 5/16” Bolt
3 RETAINER, 5/16” Bolt
Position: 13
1 DECAL, OPC Bail (International Symbol)
1 DECAL, OPC Bail (International Symbol)
Position: 13
2 BOLT, 1/4-20 x 1-1/4” Hex, GR
2 BOLT, 1/4-20 x 1-1/4” Hex, GR
Position: 13
2 TIE, Wire, 1.29 long, black
2 TIE, Wire, 1.29 long, black
Position: 14
1 KEY, Woodruff #HP-506 Hi-Pro Used on EP217019BV &
1 KEY, Woodruff #HP-506 Hi-Pro Used on EP217019BV &
Position: 14
1 ASSY, Wheel Arm Left Rear Long SP21S Incl. 4, 6, 9, 10, 11, 16 &
1 ASSY, Wheel Arm Left Rear Long SP21S Incl. 4, 6, 9, 10, 11, 16 &
Position: 14
1 SPRING, Clutch- 21S See also HANDLES &
1 SPRING, Clutch- 21S See also HANDLES &
Position: 14
1 GEAR, Differential (46 Tooth)
1 GEAR, Differential (46 Tooth)
Position: 14
1 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR 5 or
1 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR 5 or
Position: 14
1 DECAL, Ninja, Mulching System
1 DECAL, Ninja, Mulching System
Position: 14
2 NUT, 1/4-20 Hex, GR 5 was
2 NUT, 1/4-20 Hex, GR 5 was
Position: 14
1 BRACKET, Bell Crank
1 BRACKET, Bell Crank
Position: 15
1 HUB, Blade Drive 25mm I.D.
1 HUB, Blade Drive 25mm I.D.
Position: 15
1 ARM, Wheel, Right Rear
1 ARM, Wheel, Right Rear
Position: 15
1 SPRING, Idler- Torsion
1 SPRING, Idler- Torsion
Position: 15
2 PLATE, 46T Gear
2 PLATE, 46T Gear
Position: 15
1 SIDE CHUTE, 21”
1 SIDE CHUTE, 21”
Position: 15
1 DECAL, Hi Vac, Cutting Deck
1 DECAL, Hi Vac, Cutting Deck
Position: 15
2 CAP, Vinyl
2 CAP, Vinyl
Position: 15
1 SPACER, .33 x .63 x .156
1 SPACER, .33 x .63 x .156
Position: 16
3 SCREW, 3/8-16 x 1” Self-Tapping engine mount bolts
3 SCREW, 3/8-16 x 1” Self-Tapping engine mount bolts
Position: 16
1 ARM, Wheel, Left Rear
1 ARM, Wheel, Left Rear
Position: 16
1 STUD, Idler (3/8-24 thread)
1 STUD, Idler (3/8-24 thread)
Position: 16
2 WASHER, Thrust, 3/4” I.D.
2 WASHER, Thrust, 3/4” I.D.
Position: 16
1 COVER, 21” Deck
1 COVER, 21” Deck
Position: 16
2 BOLT, 1/4-20 x 2-1/2” Square Neck Carriage only 1 shown
2 BOLT, 1/4-20 x 2-1/2” Square Neck Carriage only 1 shown
Position: 16
1 BELL CRANK
1 BELL CRANK
Position: 17
4 SCREW, 5/16-24 x 21/32” Oval Head Machine
4 SCREW, 5/16-24 x 21/32” Oval Head Machine
Position: 17
1 HOLDER, Bearing (Inner Half)
1 HOLDER, Bearing (Inner Half)
Position: 17
4 SCREW, #10-32 x 1-1/2” Hex Head Cap GR
4 SCREW, #10-32 x 1-1/2” Hex Head Cap GR
Position: 17
6 BOLT, 5/16-18 x 1” Square Neck Carriage, GR 5 was 7090383 (only 1 shown)
6 BOLT, 5/16-18 x 1” Square Neck Carriage, GR 5 was 7090383 (only 1 shown)
Position: 17
1 CONTROL PANEL (w/o Electrical Switch Hole)
1 CONTROL PANEL (w/o Electrical Switch Hole)
Position: 18
2 AIR LIFT
2 AIR LIFT
Position: 18
3 WASHER, 3/8” Internal Tooth Lock
3 WASHER, 3/8” Internal Tooth Lock
Position: 18
1 GASKET, Housing
1 GASKET, Housing
Position: 18
2 BOLT, 1/4-20 x 3/4” Square Neck Carriage, GR 5 was
2 BOLT, 1/4-20 x 3/4” Square Neck Carriage, GR 5 was
Position: 18
4 SCREW, 1/4-20 x 1/2” Pan Head Self-Tap (Torx)
4 SCREW, 1/4-20 x 1/2” Pan Head Self-Tap (Torx)
Position: 19
4 WASHER, 5/16” Internal Tooth Lock
4 WASHER, 5/16” Internal Tooth Lock
Position: 19
2 NUT, 3/8-24 Hex
2 NUT, 3/8-24 Hex
Position: 19
3 WASHER, 5/16” Internal/External Tooth Lock
3 WASHER, 5/16” Internal/External Tooth Lock
Position: 19
6 WASHER, Reinforcing only 1 shown
6 WASHER, Reinforcing only 1 shown
Position: 19
2 WASHER, .33 x .88 x .09 Flat
2 WASHER, .33 x .88 x .09 Flat
Position: 20
4 NUT, 5/16-24 Hex, GR
4 NUT, 5/16-24 Hex, GR
Position: 20
1 WASHER, .390 I.D. Flat
1 WASHER, .390 I.D. Flat
Position: 20
1 BRACKET, Differential
1 BRACKET, Differential
Position: 20
6 WASHER, 5/16” Split Lock only 1 shown
6 WASHER, 5/16” Split Lock only 1 shown
Position: 20
1 SCREW, 5/16-18 x 7/8” Hex Head Cap, GR
1 SCREW, 5/16-18 x 7/8” Hex Head Cap, GR
Position: 21
1 FENDER (Weldment), EP21S
1 FENDER (Weldment), EP21S
Position: 21
1 BALL BEARING, Spherical O.D., .38 I.D.
1 BALL BEARING, Spherical O.D., .38 I.D.
Position: 21
4 SCREW, 1/4-20 x 1” Hex washer Self-Tap or
4 SCREW, 1/4-20 x 1” Hex washer Self-Tap or
Position: 21
6 NUT, 5/16-18 Hex, GR 5 was 7090196 (only 1 shown)
6 NUT, 5/16-18 Hex, GR 5 was 7090196 (only 1 shown)
Position: 21
1 TEENUT 5/16-18
1 TEENUT 5/16-18
Position: 22
6 SCREW, 1/4-20 x 1/2” Hex Flange Self-Tap
6 SCREW, 1/4-20 x 1/2” Hex Flange Self-Tap
Position: 22
1 O-RING, V21
1 O-RING, V21
Position: 22
1 SPACER, Axle Gear
1 SPACER, Axle Gear
Position: 22
2 NUT, 1/2” Push
2 NUT, 1/2” Push
Position: 22
1 BUSHING, Differential, .328 x .625 x .41
1 BUSHING, Differential, .328 x .625 x .41
Position: 23
1 DECAL, Caution Symbols (International)
1 DECAL, Caution Symbols (International)
Position: 23
1 HOLDER, Bearing (Outer Half)
1 HOLDER, Bearing (Outer Half)
Position: 23
1 ASSEMBLY, Long Axle
1 ASSEMBLY, Long Axle
Position: 23
4 BEARING, Nyliner
4 BEARING, Nyliner
Position: 23
2 BOLT, 5/16-18 x 3/4” Hex Flange Lock GR
2 BOLT, 5/16-18 x 3/4” Hex Flange Lock GR
Position: 24
1 BOLT, 5/16-18 x 2-1/4” Hex Flange Lock
1 BOLT, 5/16-18 x 2-1/4” Hex Flange Lock
Position: 24
2 SCREW, 1/4-20 x 1/2” Hex Flange Self-Tap or
2 SCREW, 1/4-20 x 1/2” Hex Flange Self-Tap or
Position: 24
4 GEAR, Pinion (12 tooth)
4 GEAR, Pinion (12 tooth)
Position: 24
1 SCREW, 5/16-18 x 1/4” Set
1 SCREW, 5/16-18 x 1/4” Set
Position: 24
2 NUT, 5/16-18 Hex Flange Lock, GR 5 or
2 NUT, 5/16-18 Hex Flange Lock, GR 5 or
Position: 25
1 BUSHING, .388 x .625 x 1.62 Flanged matl: powdered metal
1 BUSHING, .388 x .625 x 1.62 Flanged matl: powdered metal
Position: 25
1 NUT, 3/8-24 Hex Center Lock, GR
1 NUT, 3/8-24 Hex Center Lock, GR
Position: 25
4 SPACER, Pinion Gear
4 SPACER, Pinion Gear
Position: 25
2 WASHER, 1/2” Flat
2 WASHER, 1/2” Flat
Position: 25
1 NUT, 5/16-18 Hex Center Lock
1 NUT, 5/16-18 Hex Center Lock
Position: 26
2 WASHER, 7/16” Flat
2 WASHER, 7/16” Flat
Position: 26
1 GUIDE, Thrust Plate (3/8-24 thread)
1 GUIDE, Thrust Plate (3/8-24 thread)
Position: 26
4 SHAFT, Pinion
4 SHAFT, Pinion
Position: 26
1 DECAL, Adjustment
1 DECAL, Adjustment
Position: 26
1 LEVER, Shift
1 LEVER, Shift
Position: 27
1 COVER, Belt- IP21S
1 COVER, Belt- IP21S
Position: 27
1 THRUST PLATE, Short
1 THRUST PLATE, Short
Position: 27
4 NUT, #10-32 Hex Nyloc
4 NUT, #10-32 Hex Nyloc
Position: 27
1 DECAL, Thatcherizer
1 DECAL, Thatcherizer
Position: 27
1 NUT, 5/16-24 Hex Center Lock GR
1 NUT, 5/16-24 Hex Center Lock GR
Position: 28
1 SCREW, 5/16-18 x 1/2” Hex Head Cap, GR
1 SCREW, 5/16-18 x 1/2” Hex Head Cap, GR
Position: 28
1 WASHER, 3/8” Flat
1 WASHER, 3/8” Flat
Position: 28
1 ASSY, Left Housing (Phantom)
1 ASSY, Left Housing (Phantom)
Position: 28
1 CLIP, Wiring Harness
1 CLIP, Wiring Harness
Position: 29
1 WASHER, 5/16” Flat
1 WASHER, 5/16” Flat
Position: 29
1 SHIELD- Hex Shaft
1 SHIELD- Hex Shaft
Position: 29
1 HOUSING, Left
1 HOUSING, Left
Position: 29
4 SCREW, 5/16-18 x 1-7/8” Curved Head GR 2 or
4 SCREW, 5/16-18 x 1-7/8” Curved Head GR 2 or
Position: 30
2 RETAINING RING, .625 External
2 RETAINING RING, .625 External
Position: 30
3 GASKET, 5/8” O. D.
3 GASKET, 5/8” O. D.
Position: 30
4 KNOB, 5/16-18 Wing (Black)
4 KNOB, 5/16-18 Wing (Black)
Position: 31
1 COTTER PIN, .06 x .50 YZ or
1 COTTER PIN, .06 x .50 YZ or
Position: 31
2 SCREW, 1/4-20 x 1-1/2 Hex Head Cap GR
2 SCREW, 1/4-20 x 1-1/2 Hex Head Cap GR
Position: 32
2 WASHER, .28 x .63 x .06 Flat
2 WASHER, .28 x .63 x .06 Flat
Position: 32
5 WASHER, 1/4” Internal Tooth Lock
5 WASHER, 1/4” Internal Tooth Lock
Position: 33
1 LINK, Transfer (1/4-28 thread)
1 LINK, Transfer (1/4-28 thread)
Position: 33
3 NUT, 1/4-20 Hex or
3 NUT, 1/4-20 Hex or
Position: 34
2 NUT, 1/4-28 Hex See also HANDLES &
2 NUT, 1/4-28 Hex See also HANDLES &
Position: 34
1 SCREW, 1/4-20 x 2” Hex Head Cap, GR
1 SCREW, 1/4-20 x 2” Hex Head Cap, GR
Position: 35
1 BALL JOINT, 1/4-28 See also HANDLES &
1 BALL JOINT, 1/4-28 See also HANDLES &
Position: 35
2 BUSHING, .27 x .35 x .4 Flange
2 BUSHING, .27 x .35 x .4 Flange
Position: 36
1 WASHER, 1/4” Internal Tooth Lock
1 WASHER, 1/4” Internal Tooth Lock
Position: 36
1 PIN, 1/4 x 1-1/2”
1 PIN, 1/4 x 1-1/2”
Position: 37
1 DISC, Driven (Cantilever)
1 DISC, Driven (Cantilever)
Position: 37
1 PUSH-NUT, 1/4”
1 PUSH-NUT, 1/4”
Position: 38
1 BALL BEARING- 3/4” Bore
1 BALL BEARING- 3/4” Bore
Position: 38
2 BALL JOINT, 1/4-28
2 BALL JOINT, 1/4-28
Position: 39
1 SHAFT, Hex Drive
1 SHAFT, Hex Drive
Position: 39
4 NUT, 1/4-28 Hex
4 NUT, 1/4-28 Hex
Position: 40
1 PULLEY, Poly-V (2” O.D.)
1 PULLEY, Poly-V (2” O.D.)
Position: 40
1 FOAM GRIP, 18.75” long
1 FOAM GRIP, 18.75” long
Position: 41
1 BELT, Engine Drive (Stretch)
1 BELT, Engine Drive (Stretch)
Position: 41
1 SCREW, 3/8-16 x 2” Hex Head Cap, GR
1 SCREW, 3/8-16 x 2” Hex Head Cap, GR
Position: 42
1 ASSEMBLY, Steel Drive Disc 7053263, Drive Disc & Bushing
1 ASSEMBLY, Steel Drive Disc 7053263, Drive Disc & Bushing
Position: 42
1 NUT, 3/8-16 Hex Center Lock
1 NUT, 3/8-16 Hex Center Lock
Position: 43
1 BUSHING, Powdered Metal
1 BUSHING, Powdered Metal
Position: 43
4 WASHER, 5/16” Internal Tooth Lock
4 WASHER, 5/16” Internal Tooth Lock
Position: 44
1 RETAINER, 5/16” Bolt
1 RETAINER, 5/16” Bolt
Position: 44
8 WASHER, 7/16” Flat
8 WASHER, 7/16” Flat
Position: 45
1 SPACER, .500 x .65 x 1.75
1 SPACER, .500 x .65 x 1.75
Position: 45
2 WASHER, Nylon
2 WASHER, Nylon
Position: 46
1 BRACKET, Deck, P21S
1 BRACKET, Deck, P21S
Position: 46
1 ROD, Speed Control (1/4-28 thread)
1 ROD, Speed Control (1/4-28 thread)
Position: 47
1 SPRING, Wheel Drive
1 SPRING, Wheel Drive
Position: 47
1 GUIDE, Rope (1/4-20 thread)
1 GUIDE, Rope (1/4-20 thread)
Position: 48
1 BOLT, 5/16-18 x 1/2”, Short Neck Carriage, GR
1 BOLT, 5/16-18 x 1/2”, Short Neck Carriage, GR
Position: 48
1 NUT, 1/4-28 Hex GR 5 or B
1 NUT, 1/4-28 Hex GR 5 or B
Position: 49
1 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR 5 or
1 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR 5 or
Position: 49
1 CABLE-TIE, 7”
1 CABLE-TIE, 7”
Position: 50
2 NUT, 5/16-18 Hex Flange Lock, GR 5 or
2 NUT, 5/16-18 Hex Flange Lock, GR 5 or
Position: 50
1 *THROTTLE CONTROL, .48 x .61
1 *THROTTLE CONTROL, .48 x .61
Position: 51
1 NUT, 3/8-16 Hex, GR 5 or B
1 NUT, 3/8-16 Hex, GR 5 or B
Position: 51
1 THROTTLE KNOB
1 THROTTLE KNOB
Position: 52
1 KNOB, Shift
1 KNOB, Shift
Position: 53
1 CLAMP, 7/8” Double Cable
1 CLAMP, 7/8” Double Cable
Position: 54
1 SCREW, #8-32 x 1/2” Cross Recess Filister Head Machine
1 SCREW, #8-32 x 1/2” Cross Recess Filister Head Machine
Position: 55
1 NUT, #8-32 Hex
1 NUT, #8-32 Hex
Position: 56
1 SCREW, 5/16-18 x 1-1/4” Hex Washer Head Self-Tap
1 SCREW, 5/16-18 x 1-1/4” Hex Washer Head Self-Tap
Position: 57
1 WASHER, Belleville
1 WASHER, Belleville
Position: 58
1 SCREW, 5/16-24 x 1” Hex Head Cap GR
1 SCREW, 5/16-24 x 1” Hex Head Cap GR
Position: 59
1 WASHER, 11/32” Flat
1 WASHER, 11/32” Flat
Position: 60
1 COTTER PIN, 5/16 Self Lock
1 COTTER PIN, 5/16 Self Lock
Position: 61
1 DECAL, Easy Speed, Control Panel
1 DECAL, Easy Speed, Control Panel
Position: 62
1 CLAMP, Casing
1 CLAMP, Casing
Position: 63
1 SCREW,#10-32 x 5/8” Self-Tap
1 SCREW,#10-32 x 5/8” Self-Tap
Position: 64
1 *ASSY, Driven Disc (Cantilever) Euro
1 *ASSY, Driven Disc (Cantilever) Euro
Position: 7042934
1 ASSEMBLY, Clutch Idler (incl. items 6, 10, 11 & 12)
1 ASSEMBLY, Clutch Idler (incl. items 6, 10, 11 & 12)
Position: 7051913
1 ASSEMBLY, Deck Bracket (Incl. items 8, 45 & 46)
1 ASSEMBLY, Deck Bracket (Incl. items 8, 45 & 46)
Position: 7052987
1 ASSEMBLY, Transmission (Incl. items 1 thru 30)
1 ASSEMBLY, Transmission (Incl. items 1 thru 30)
Position: 7059070
KIT, Snapperizer “HV” (Incl. items 1 & 2 thru 5) used on EP217019BV
KIT, Snapperizer “HV” (Incl. items 1 & 2 thru 5) used on EP217019BV
Position: 7060440
32oz. *”00” Grease not shown
32oz. *”00” Grease not shown
Position: 7061017
KIT, Recycling Cover (Incl. items 1 & 3 below) for 4HP & above engines
KIT, Recycling Cover (Incl. items 1 & 3 below) for 4HP & above engines
Position: 7061200
KIT, Recycling Plug (Incl. items 2 & 3 below) for 4HP & above engines
KIT, Recycling Plug (Incl. items 2 & 3 below) for 4HP & above engines
Position: 7061201
KIT, Thatcherizer (Incl. items 1 thru 27)
KIT, Thatcherizer (Incl. items 1 thru 27)
Position: 7061256
KIT, Snapperizer “F & M” (Incl. items 1& 2A thru 5) used on ERP2167519BV &
KIT, Snapperizer “F & M” (Incl. items 1& 2A thru 5) used on ERP2167519BV &
Position: 7063041
1 THROTTLE CONTROL, .48 x .61 (conduit length: 48-1/2”)
1 THROTTLE CONTROL, .48 x .61 (conduit length: 48-1/2”)
Position: 7074460