Exploderad vy elt 18538 f SNAPPER elt18538f
Upptäck den fullständiga exploderade vyn elt 18538 f SNAPPER elt18538f – en oumbärlig guide för att identifiera reservdelar. Vår presentation hjälper dig förstå varje komponent i din elt 18538 f. Hitta snabbt delarna till din elt 18538 f SNAPPER elt18538f.
Reparationsassistent
Powered by ChatGPT
Lista över reservdelar
2 WHEEL & TIRE ASSEMBLY, Front
Position: 1
2 PIVOT, Hood Powdered Metal
Position: 1
1 CAP, Steering Wheel, Plain
Position: 1
1 CAPSCREW, Hex Head, Taptite, 5/16-18 x 3/4
Position: 1
1 PAD, Foot Pedal Reverse
Position: 1
1 VALVE, Oil Drain
Position: 1
1 VALVE, Oil Drain
Position: 1
1 SEAT, Low Back, Steel Pan
Position: 1
1 SEAT, Hi Back, Steel Pan
Position: 1
1 SWITCH ASSEMBLY, Ignition, 6-Pole (Includes Ref. 2, 3, 4 & 5)
Position: 1
1 DECAL, Height Of Cut
Position: 1
2 BOLT, Rear Wheel (42” Only)
Position: 1
2 NUT, Push, 3/8
Position: 1
2 NUT, Hex Flange Center Locking, 3/8-16
Position: 1
1 CLIP, Pin, Safety
Position: 1
3 NUT, Hex, Flange, 9/16-8
Position: 1
1 DECAL, Snapper, LH Hood Stripe
Position: 1
1 TIRE, Turf 15 X 6.00 - 6 Saver TL
Position: 2
16 NUT, Hex, Flange Whizlock, 5/16-18
Position: 2
1 NUT, Hex Lock, ESNA Light, 5/8-18, Thin
Position: 2
8 NUT, Hex, Flange Whizlock, 5/16-18
Position: 2
2 CARRIAGE BOLT, 5/16-18 x 1-1/4
Position: 2
12 CAPSCREW, Whizlock, 1/4-20 x 5/8
Position: 2
4 WASHER, Plain, 5/16
Position: 2
1 WASHER, 5/8
Position: 2
1 CARRIAGE BOLT, 1/4-20 x 5/8 G5
Position: 2
1 CAPSCREW, Hex Washer Head, Taptite, 3/8-16 x
Position: 2
2 WASHER, 1/2 (42” Only)
Position: 2
1 ROD, Deflector
Position: 2
2 WASHER, Plain, 13/32 x 1-1/2 x 1/8
Position: 2
6 WASHER, Belleville
Position: 2
1 DECAL, Snapper, RH Hood Stripe
Position: 2
1 TUBE, Tire, Front
Position: 3
1 WASHER, 5/8
Position: 3
1 ROD, Bypass, 11.44 LG Yellow
Position: 3
2 SPACER, Pivot 0.330ID 1.76OD .37TH Powdered Metal
Position: 3
1 EDGING, Rubber, Short (B&S V-Twin)
Position: 3
1 EDGING, Rubber, Long (B&S Single Only)
Position: 3
1 EDGING, Rubber, Short (B&S V-Twin & Kohler Single)
Position: 3
1 DUCT, Air Inlet Plastic
Position: 3
1 LATCH, Seat 20GA E-Coat
Position: 3
1 LOCKWASHER, Internal Tooth, 5/8
Position: 3
1 WASHER, Plain, 13/32 x 1-1/2 x 1/8
Position: 3
2 WHEEL, Gauge (42” Only)
Position: 3
6 BOLT, Carriage, 5/16-18 x 3/4
Position: 3
2 NUT, ESNA, Lock, 1/2-13 (Thin)
Position: 3
3 PULLEY, RH Arbor & LH Arbor, 4-1/4
Position: 3
3 PULLEY, RH Arbor & LH Arbor, 4-1/2
Position: 3
1 DECAL, Ignition Switch Symbol, White/Black
Position: 3
1 WHEEL & BUSHINGS ASSEMBLY, Front
Position: 4
2 CARRIAGE BOLT, 5/16-18 x
Position: 4
1 STEERING WHEEL, w/Aluminum Insert
Position: 4
2 PIN, Quick
Position: 4
1 CONTROL, Throttle Double 20.5, 23.5 B&S Single
Position: 4
1 CONTROL, Throttle Double 34.7, 36 B&S Twin
Position: 4
1 CONTROL, Throttle Double 19” Long (Kohler Single)
Position: 4
1 CONTROL, Throttle Double 34.7” Long (B&S Twin)
Position: 4
1 SCREW, Pan Head #10-24 x 1/2
Position: 4
4 CAPSCREW, Hex Head Flange Dog Point, 5/16-18 x
Position: 4
1 NUT, Hex, Flange, 5/8-32
Position: 4
1 NUT, Hex Flange Whiz, 1/4-20
Position: 4
11 NUT, Hex, Flange Whizlock, 5/16-18 (38” Only)
Position: 4
13 NUT, Hex, Flange Whizlock, 5/16-18 (42” Only)
Position: 4
1 SPACER
Position: 4
2 SPACER
Position: 4
2 HUB, Pulley, RH (Middle)
Position: 4
2 HUB, Pulley, RH
Position: 4
1 DECAL, Steering Wheel Icon
Position: 4
4 BEARING
Position: 5
14 SCREW, Taptite, 5/16-18 x 5/8
Position: 5
1 RING, Klipring Extension
Position: 5
1 NUT, Hex Flange, 5/16-18 ESNA
Position: 5
1 SPACER, Foot Pedal Powdered Metal
Position: 5
2 CLAMP, Hose Type E
Position: 5
2 PUSH NUT
Position: 5
4 SPACER, 0.32 ID x 1-1/2 OD x 3/10 THK Powdered Metal Yellow
Position: 5
1 COVER, Ignition
Position: 5
1 GRIP
Position: 5
1 SPACER, 0.387 ID x 1-1/2 OD x 1.04 LG Powdered Metal
Position: 5
1 SPRING, Torsion
Position: 5
1 CAPSCREW, Hex Head, 3/8-16 x 2-1/2
Position: 5
1 PIN, Hitch
Position: 5
3 SPACER
Position: 5
1 DECAL, Height of Cut
Position: 5
1 FITTING, Grease, 1/4-28 Thread
Position: 6
1 CAPSCREW, Hex Head, 5/8-11 x 3-1/4 G5
Position: 6
2 WASHER
Position: 6
6 NUT, Hex, Flange Whizlock, 5/16-18
Position: 6
1 HOSE, Fuel, 45-1/2” Long (B&S V-Twin)
Position: 6
1 HOSE, Fuel 55” Long (B&S Single Only)
Position: 6
1 HOSE, Fuel, 45-1/2” Long (B&S V-Twin & Kohler Single)
Position: 6
1 KNOB, Cruise Lock Green Plastic
Position: 6
1 IGNITION KEY (Set of 2)
Position: 6
1 ROD, Lift Handle E-Coat, 17.7 LG
Position: 6
1 CAPSCREW, Hex Head, 3/8-16 x 2-1/4
Position: 6
2 NUT, Hex Flange, 3/8-16 ESNA (42” Only)
Position: 6
6 NUT, Hex, Flange Whizlock, 5/16-18
Position: 6
1 WASHER, 3/8
Position: 6
1 DECAL, Snapper Rear Stripe, Silver/ 8.5LG
Position: 6
2 VALVE STEM & CAP
Position: 7
1 WASHER, Flat, 5/8
Position: 7
2 BUSHING, Steering
Position: 7
1 ACTUATOR, RMO Switch 20GA
Position: 7
2 CLIP, Hose, Plastic, Push-In
Position: 7
1 COVER, Steering Shaft Plastic
Position: 7
2 CARRIAGE BOLT, 5/16-18 x 3/4
Position: 7
1 SWITCH, Headlights, 2 Terminal
Position: 7
4 WASHER, 3/8
Position: 7
11 BOLT, Carriage, 5/16-18 x 3/4 (38” Only)
Position: 7
13 BOLT, Carriage, 5/16-18 x 3/4 (42” Only)
Position: 7
1 DEFLECTOR & SUPPORT ASSEMBLY, Chute Riveted
Position: 7
1 PULLEY ASSEMBLY
Position: 7
6 BEARING
Position: 7
1 DECAL, Transmission Tow/ Release Lever
Position: 7
8 WASHER, 3/4
Position: 8
4 NUT, Hex, Flange Whizlock, 5/16-18
Position: 8
1 TRANSMISSION ASSEMBLY, K46
Position: 8
1 TRANSMISSION ASSEMBLY, K46HD (Used with 22” Tire Models)
Position: 8
1 ROD, Cruise Latch, 16.97LG
Position: 8
2 CAPSCREW, Hex Head, Taptite, 5/16-18 x 3/4
Position: 8
1 PLUG, Hole, Square
Position: 8
1 WASHER, Plain, 21/64 x 1-1/4
Position: 8
2 IDLER, Flat
Position: 8
1 SPACER
Position: 8
3 GASKET, Foam
Position: 8
1 DECAL, Fuel Level
Position: 8
4 WASHER, Special Yellow
Position: 9
4 SCREW, Hex Head Flange Lock, 5/16-18 x 2-1/2
Position: 9
2 CLIP, Linkage, Black
Position: 9
4 SCREW, Taptite, 5/16-18 x 5/8
Position: 9
2 WASHER, Plain, 5/16
Position: 9
4 BOLT, Carriage, 5/16-18 x 3/4
Position: 9
1 PLUG, Hour Meter (Kohler and B&S Single)
Position: 9
1 SPRING, Torsion, 2.12 LG Black
Position: 9
2 PULLEY (42” Only)
Position: 9
2 PULLEY (38” Only)
Position: 9
1 NUT, Whizlock, 3/8-16
Position: 9
2 CAPSCREW, Hex Head, Flange Whiz Lock, 5/16-18 x 3/4
Position: 9
1 DECAL, Tunnel
Position: 9
1 DECAL, Safety Instructions (CE)
Position: 9
4 RING, Retaining
Position: 10
4 CAPSCREW, Hex Head, Flange Whiz Lock, 5/16-18 x 3/4
Position: 10
1 ROD, Parking Brake, 16.38 LG Yellow
Position: 10
1 KEY, Hi-Pro, 1/4 x 2-1/2
Position: 10
2 KEY, Square, 1/4 x 1/4 x 29/32 Hard
Position: 10
1 KNOB, Brake Lock Plastic
Position: 10
4 NUT, Hex Flange, 5/16-18 ESNA
Position: 10
1 METER, Hour, LCD (B&S V-Twin Only)
Position: 10
1 CAPSCREW, Hex Head, 3/8-16 X 1-3/4
Position: 10
1 SPRING, Extension, Idler Arm (44” Mower Deck)
Position: 10
1 SPRING, Extension, Idler Arm (50” Mower Deck)
Position: 10
4 NUT, Hex Flange, 3/8-16 ESNA
Position: 10
1 DECAL, Belts, Blades
Position: 10
4 CAP, Hub
Position: 11
2 NUT, Whizlock, 3/8-16
Position: 11
1 SPACER
Position: 11
2 CARRIAGE BOLT, 3/8-16 x 1-1/4
Position: 11
1 PULLEY
Position: 11
1 DASHBOARD
Position: 11
2 BOLT, Shoulder 5/16-18 G5
Position: 11
1 WASHER, Plain, 1/4 (6 Total for Export)
Position: 11
1 SPACER, Pivot 0.330ID 1.76OD .37TH Powdered Metal
Position: 11
2 BEARING, Upper
Position: 11
1 V BELT, Arbor Drive, 44”
Position: 11
1 V BELT, Arbor Drive, 44” (CE Only)
Position: 11
1 V-BELT, Arbor Drive, 50”
Position: 11
4 WASHER, 1/2
Position: 11
1 HUB, Adapter, LH
Position: 11
2 KEY, 3/16 x 3/16 x
Position: 12
14 CAPSCREW, Hex Head, Flange Whiz Lock, 5/16-18 x 3/4
Position: 12
1 GEAR, Steering, 26 teeth
Position: 12
1 V-BELT, Drive Belt, Aramid/Kevlar
Position: 12
1 SPACER, 1.01 ID x 1.68 OD x 3/8 LG Powdered Metal Yellow
Position: 12
1 GUIDE, Hood RH
Position: 12
2 SPRING, Compression
Position: 12
1 NUT, Wing, 1/4-20
Position: 12
3 NUT, Hex, Flange Whizlock, 5/16-18
Position: 12
2 NUT, Hex Lock, ESNA Light, 5/8-18, Thin
Position: 12
1 CAPSCREW, Hex Head, 3/8-16 x 1-1/4, G8
Position: 12
4 WHEEL, Gauge
Position: 12
1 DECAL, LT200 18.5HP
Position: 12
1 DECAL, LT200 20HP
Position: 12
1 DECAL, LT200 22HP
Position: 12
2 WASHER
Position: 13
2 SPACER, Sector Gear 0.374ID 1.25OD Powdered Metal Yellow
Position: 13
1 SPRING, Extension 07.52 LG Black
Position: 13
1 TIE, Self Locking 7-5/16
Position: 13
2 WASHER
Position: 13
4 WASHER, Spring Black
Position: 13
1 CARRIAGE BOLT, 1/4-20 x 7/8
Position: 13
1 SPRING, Extension 07.75 LG Black
Position: 13
1 PIN, Hitch
Position: 13
2 SPACER, Pulley, 38” Deck
Position: 13
4 BOLT, Rear Wheel
Position: 13
29 CAPSCREW, Hex Head, Taptite, 5/16-18 x 3/4
Position: 13
1 CAPSCREW, Hex Head, Serrated Flange Taptite, 5/16-18 x 2 G5
Position: 13
1 DECAL, Danger, Chute in Place
Position: 13
2 SPACER, 0.77 ID x 1-1/4 OD x 1.65 LG Powdered Metal Black
Position: 14
2 CAPSCREW, Hex, Flange, Whizlock, 3/8-16 x
Position: 14
1 WASHER, Flat, 5/16
Position: 14
1 PULLEY, 3 OD Plastic
Position: 14
1 CLUTCH ASSEMBLY, Long OGURA
Position: 14
1 CLUTCH ASSEMBLY, Mid-Range OGURA
Position: 14
2 RIVET, Pop, Stem Black
Position: 14
2 COVER, Spring
Position: 14
1 NUT, Push On
Position: 14
1 NUT, 3/8-16, Hex Flange MAC Locking Large, Black
Position: 14
2 SPACER, .532 ID x 3/4 OD x 1-1/4 LG Yellow
Position: 14
2 RETAINING RING, Extension, 1-3/4
Position: 14
3 WASHER
Position: 14
1 NUT, 1/4-20
Position: 14
1 DECAL, Pinch Point
Position: 14
2 WHEEL & TIRE ASSEMBLY, Rear 20”
Position: 15
2 WHEEL & TIRE ASSEMBLY, Rear 22”
Position: 15
1 NUT, Hex Flange Two-Way Lock, 5/8-11
Position: 15
1 SHAFT, Steering Gear & Spline Yellow
Position: 15
1 CAPSCREW, Hex Head, 5/16-18 x
Position: 15
2 NUT, Hex Flange, 3/8-16 ESNA
Position: 15
1 WASHER
Position: 15
1 GUIDE, Hood LH
Position: 15
1 POD, LH Cup Holder
Position: 15
1 HOLD DOWN, Battery
Position: 15
4 CLIP, Spring
Position: 15
2 BOLT, Carriage, 5/16-18 x 3/4
Position: 15
2 NUT, ESNA, Lock, 1/2-13 (Thin)
Position: 15
10 SCREW, Hex, Washer Head, Taptite, 3/8-16 x 3/4
Position: 15
1 SHAFT, Arbor
Position: 15
26 CAPSCREW, Hex Head, Taptite, 5/16-18 x 3/4
Position: 15
1 DECAL, Danger, Hand Under Deck
Position: 15
1 TIRE, Turf 22 X 8.00 - 8 Saver TL
Position: 16
1 TIRE, Turf 22 X 10.00 - 8 Saver TL
Position: 16
1 CARRIAGE BOLT, 5/16-18 x
Position: 16
1 CAPSCREW, 7/16-20 x 3-1/2, Hex Head
Position: 16
1 CAPSCREW, 7/16-20 x
Position: 16
12 NUT, Hex Flange Whiz, 1/4-20
Position: 16
1 ELBOW FITTING
Position: 16
1 SWITCH, Push Button (NC)
Position: 16
2 WASHER, 1/2
Position: 16
1 V-BELT, 91.10 LG Kevlar (38" Decks)
Position: 16
1 V-BELT, 94.45 LG Kevlar (42" Decks)
Position: 16
1 CLIP, Pin, Safety
Position: 16
3 SHIELD, Grass, Lower
Position: 16
1 TUBE, Tire, Rear, 22 X 8 -
Position: 17
1 TUBE, Tire, Rear, 22 X 10 -
Position: 17
2 LOCKNUT, Hex, Flange, 7/16-14
Position: 17
1 WASHER, Plain, 5/16
Position: 17
1 PULLEY, Idler
Position: 17
1 LOCKWASHER, 7/16
Position: 17
1 BUSHING
Position: 17
3 TIE, Self Locking 7-5/16
Position: 17
2 PIN, Threaded Shoulder
Position: 17
3 BLADE, 44”
Position: 17
1 DECAL, 38”
Position: 17
1 DECAL, 42”
Position: 17
1 DECAL, 50”
Position: 17
1 WHEEL, Hub
Position: 18
4 BUSHING, Nylon, 3/4 Diameter
Position: 18
1 CAPSCREW, Hex Head, 5/16-18 x 1-3/4
Position: 18
1 SPRING, Extension
Position: 18
4(1) SCREW, Hex, Washer Head, Taptite, 3/8-16 x 1-1/4
Position: 18
3 CAPSCREW, Hex Head, Taptite, 3/8-16 x 1-1/2 (B&S Single Only)
Position: 18
1 ROD, Dash Support
Position: 18
1 TANK, Fuel
Position: 18
1 OUTLET, 12 Volt DC Power
Position: 18
1 ROD, Bail Mowers Yellow
Position: 18
1 FITTING, Grease
Position: 18
3 WASHER, Hex
Position: 18
1 DECAL, Hand Under Deck (CE)
Position: 18
3 FITTING, Zerk
Position: 19
1 PIN, Cotter 3/32 x 3/4
Position: 19
1 WASHER, 3/8
Position: 19
1 SCREW, Taptite, 1/4-20 x 1/2
Position: 19
1 CAP, Gas
Position: 19
1 PLUG, Hole Models W/O 12V Adapter
Position: 19
2 NUT, Hex, Flange, Whizlock, 5/16-18 x 1/2
Position: 19
1 SHAFT, Spindle, 38” Deck
Position: 19
3 WASHER, Spring
Position: 19
1 LINK, Drag
Position: 20
1 ROD, Brake, 15.1 LG
Position: 20
1 RETAINER, Clutch, Yellow
Position: 20
1 RETAINER, Clutch, Black
Position: 20
1 NUT, Hex, Nylon, Lock, #10-24
Position: 20
1 PAD, Footrest LH
Position: 20
1 SWITCH, Push Button (NO/NC)
Position: 20
2 DECAL, CAUTION! Pinch Point
Position: 20
3 CAPSCREW, Hex Head, 7/16-14 x 1-1/4
Position: 20
3 BLADE, 18-1/8, 50” Deck
Position: 20
1 SPRING, Extension 05.37 LG Black
Position: 21
1 LOCKWASHER, External Tooth, 3/8
Position: 21
2 BOLT, Shoulder
Position: 21
4 WASHER, Belleville
Position: 21
2 BOLT, Carriage, 5/16-18 x 3/4
Position: 21
8 BOLT, Carriage, 5/16-18 x 3/4 (CE Only)
Position: 21
2 NUT, Hex Nylock 3/8-24
Position: 22
1 PEDAL, Brake Rubber
Position: 22
1 PAD, Footrest RH
Position: 22
4 SCREW, Taptite, 5/16-18 x 5/8
Position: 22
2 NUT, Hex 9/16-18
Position: 22
4 WASHER, 3/4
Position: 23
1 PIN, Quick
Position: 23
4 SCREW, Taptite, 1/4-20 x 1/2
Position: 23
1 HEADLIGHT ASSEMBLY (Includes Ref. 24, 25, 26 & 27)
Position: 23
2 SPACER (Used on 38” & 42” Mower
Position: 23
2 SPACER (Used on 44” & 50” Mower
Position: 23
2 BLADE, Mower 42” (42” Only)
Position: 23
2 BLADE, Mower 38” (38” Only)
Position: 23
2 NUT, Hex, Flange Whizlock, 5/16-18
Position: 23
8 NUT, Hex, Flange Whizlock, 5/16-18
Position: 23
1 ROD, Brake Return, 12.60 LG
Position: 24
1 PIPE, Exhaust w/Flange LH B&S INT
Position: 24
1 INSERT, Lightbar
Position: 24
6 SCREW, Hex, Washer Head, Plastite, 1/4-20 x 1/2
Position: 24
2 SOCKET ASSEMBLY
Position: 24
2 TRUNNION, Powdered Metal
Position: 24
2 WASHER, Spindle Blade Powdered Metal
Position: 24
2 NUT, Hex, Flange, Locking, 3/8-16
Position: 25
1 PIPE, Exhaust w/Flange RH B&S INT
Position: 25
1 HEADLIGHT ASSEMBLY
Position: 25
2 SCREW, Taptite, 5/16-18 x 5/8
Position: 25
2 BULB, 1141-12V 21CP
Position: 25
2 ROD, Lower Life, 10.00 LG
Position: 25
1 ROD, Cruise Latch, 2.83 LG
Position: 26
2(1) GASKET, Exhaust B&S
Position: 26
1 POD, RH Lift Quadrant
Position: 26
1 REFLECTOR, Headlight
Position: 26
2 SHAFT, Arbor, RH
Position: 26
3 NUT, Hex, Flange Whizlock, 5/16-18
Position: 26
2 BUSHING, Powdered Metal
Position: 27
1 SPRING, Tension, Clutch
Position: 27
4(2) LOCKWASHER, 5/16
Position: 27
1 LENS, Headlight
Position: 27
1 ROD, Lift, 5.43 LG
Position: 27
2 CARRIAGE BOLT, 1/4-20 x 1, Black
Position: 27
2 CAPSCREW, Hex Head, 3/8-16 x 1-1/4, .141 Thread G5
Position: 28
1 LATCH, Cruise Powdered Metal
Position: 28
4(2) CAPSCREW, Socket Head, 5/16-18 x 3/4
Position: 28
1 CLIP, Speed Wire
Position: 28
1 SPRING, Extension 5.10 LG Black (Used on 44” & 50” Mower
Position: 28
1 COVER, Arbor, RH
Position: 28
2 CAPSCREW, 7/16-14 x
Position: 29
1 BOLT, Shoulder 5/16-18 G5
Position: 29
1 NUT, Hex, Flange, 1/4-20
Position: 29
2 NUT, Push On
Position: 29
1 MUFFLER, B&S Twin
Position: 30
1 COVER, Terminal
Position: 30
2 WASHER, Plain, 1/4 (6 Total for Export)
Position: 30
2 BUSHING, Axle Pivot Powdered Metal
Position: 31
1 BOLT, Shoulder 5/16-18 G5
Position: 31
1 CLIP, Wire
Position: 31
1 HARNESS, Wiring
Position: 31
1 CLAMP
Position: 31
1 AXLE, Front Iron Casting Machined
Position: 32
3 SCREW, Taptite, 5/16-18 x 5/8
Position: 32
1 CABLE, Solenoid to Starter
Position: 32
2 NUT, Hex Lock, ESNA, 1/4-20
Position: 32
2 RING, Klipring Extension
Position: 33
1 MUFFLER, B&S Single
Position: 33
1 MUFFLER, B&S Single
Position: 33
1 SOLENOID
Position: 33
1 WASHER, Flat, 5/16
Position: 33
2 CAP, Hub
Position: 34
1 PIPE, Exhaust w/Flange B&S 1 Cycle
Position: 34
1 PIPE, Exhaust w/Flange Kohler
Position: 34
2 SCREW, Taptite, 1/4-20 x 1/2
Position: 34
1 DEFLECTOR, Plastic
Position: 34
1 CAPSCREW, Hex Head, Flange Whiz Lock, 5/16-18 x 3/4
Position: 35
2 LOCKWASHER, External Tooth, 5/16
Position: 35
1 SPRING
Position: 35
2 NUT, Hex, 5/16-24 NF
Position: 36
1 PAD, Foot Pedal Forward
Position: 37
1 CABLE, #6 x 10 Long, with 2 Ring Terminals, Battery to Solenoid
Position: 37
2 NUT, Hex, Flange Whizlock, 5/16-18
Position: 38
1 PLUG, Plastic (Not Shown)
Position: 38
1 PLUG, Plastic
Position: 38
2 CARRIAGE BOLT, 5/16-18 x 3/4
Position: 40
1 BOOT, Insulator
Position: 41
1 BATTERY
Position: 42
1 SWITCH, Push Button (NO), Reverse Pedal
Position: 43
2 NUT, Hex, Full, 1/4-20
Position: 44
2 LOCKWASHER, 1/4
Position: 45
2 WASHER, 1/4 I.D.
Position: 46
1 CABLE, Battery to Ground
Position: 47
2 CAPSCREW, Hex Head, 1/4-20 x 3/4
Position: 48
1 FUSE, Wiring Harness
Position: 49
1 NO-MOW MODULE
Position: 50
1 KEY, w/Hang Tag for RMO Module
Position: 51
1 SWITCH, PTO, Push/Pull Symbols
Position: 52