Exploderad vy Fischer sn17-84-snapper
Upptäck den fullständiga exploderade vyn Fischer sn17-84-snapper – en oumbärlig guide för att identifiera reservdelar. Vår presentation hjälper dig förstå varje komponent i din . Hitta snabbt delarna till din Fischer sn17-84-snapper.
Reparationsassistent
Powered by ChatGPT
Lista över reservdelar
2 ASSEMBLY, Front Tire & Rim (Complete) (Includes Items 1A, 1B, 3, 4, & 5)
Position: 1
1 WELDMENT, Front Axle, Wide
Position: 1
1 WELDMENT, Main Case (Standard) (shown)
Position: 1
1 WELDMENT, Main Case (Commercial) (not shown) (used on Kohler Models only)
Position: 1
1 FENDER, Right Hand (1.62” Dia. Hole)
Position: 1
10 SCREW, 10-24 x 1/2” Hex Washer Self-Tap
Position: 1
1 SEAT, Operator (11.58” tall) (Michigan V-2400 Series)
Position: 1
1 REAR GUARD, Euro Maincase
Position: 1
1 DECK, 33” Replacement (painted deck w/decals)
Position: 1
1 NUT, 3/4-16 Hex Jam, GR
Position: 1
1 RAIL, Deck Lift, Left Hand
Position: 1
1 DECAL, SNAPPER
Position: 1
1 KIT, Battery, 12 Volt, 220CCA, Dry Charge (includes decal #7012358)
Position: 1
2 ASSEMBLY, Rear Tire & Rim (Includes Items 2A, 2B & 3)
Position: 2
1 ASSEMBLY, Steering Wheel (for 5/8” shaft) (Includes item 3)
Position: 2
1 FENDER, Left Hand (1.628” I. D. Hole)
Position: 2
1 GASKET, Transmission Case
Position: 2
1 ROLLER, 1-3/8 Long
Position: 2
1 SWITCH, Seat (NC)(Gray)
Position: 2
3 NUT, 1/4-20 Hex Flange Lock
Position: 2
1 * BELT, Drive (73.75” AA Section)
Position: 2
1 RAIL, Deck Lift, Right Hand
Position: 2
1 DECAL, Battery Storage
Position: 2
1 SOLENOID, Super-Trombetta (replaces 7018817)
Position: 2
1 SOLENOID, Super-Trombetta
Position: 2
1 VALVE STEM, Snap In
Position: 3
1 LOGO, Steering Wheel
Position: 3
2 HAIR PIN, 3/32 x 1-1/2”
Position: 3
1 RING, 1/2” External Retaining (Heavy Duty)
Position: 3
2 STRAP, Rear Guard
Position: 3
2 RING, 1.85” Internal Retaining
Position: 3
2 WASHER, 49/64” I.D. x 1-1/2” O.D. Flat
Position: 3
7 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
Position: 3
1 DECAL, Safety Instructions (French/German)
Position: 3
1 DECAL, Safety Instructions (English/Dutch)
Position: 3
1 DECAL, 8-Panel Symbols, Euro RER
Position: 3
1 DECAL, Safety Instructions (Spanish/Italian)
Position: 3
1 HARNESS, Starter Wiring (Kohler Engines)
Position: 3
1 HARNESS, Starter Wiring (Briggs, AC)
Position: 3
1 * LUBE Fitting, Straight (for 3/16” hole)
Position: 4
1 * LUBE Fitting, Straight (for 1/4” hole)
Position: 4
1 * LUBE Fitting, 90 Degree, Ball Check (for 1/4” hole)
Position: 4
1 * LUBE Fitting, 90 Degree, Ball Check (for 5/16” hole)
Position: 4
1 ROLL PIN, 1/4 x 1-1/2”
Position: 4
4 SCREW, 5/16-18 x 3/4” Hex Washer Self-Tap
Position: 4
10 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
Position: 4
1 WELDMENT, Primary Chain Case Half, Right Hand
Position: 4
4 BOLT, 5/16-18 x 1” Square Neck Carriage, GR 5 YZ
Position: 4
2 BOLT, 1/4-20 x 3/4” Short Neck Carriage, GR
Position: 4
2 BEARING, Spindle
Position: 4
1 PULLEY, Deck
Position: 4
1 DECAL, Deck Symbols- International
Position: 4
1 HARNESS, Ignition Wiring (15HP Kohler Engines)
Position: 4
1 HARNESS, Ignition Wiring (14.5 B&S)
Position: 4
2 BALL BEARING, Flange (3/4” I.D.)
Position: 5
1 FOAM COVER, Steering Shaft
Position: 5
2 SWIVEL, Adjustable, 5/16-18+.109 hole
Position: 5
2 SCREW, 1/4-20 x 5/8” Hex Washer Head Self-Tap (or 7090362)
Position: 5
2 BEARING, .625 x 1.37 x .435
Position: 5
8 RETAINER, 5/16” Bolt
Position: 5
3 PLUG, 1” Hole
Position: 5
1 ASSEMBLY, Housing (Incl. grease fitting, 7010817)
Position: 5
1 PULLEY, Hub (Powdered Metal)
Position: 5
1 ASSEMBLY, Clutch Plate
Position: 5
1 DECAL, Height of Cut
Position: 5
1 HOLDER, Fuse (Includes Fuse)
Position: 5
1 HOLDER, Fuse (Includes 7016169 10 AMP Fuse)
Position: 5
2 WASHER, .77 x 1.13 x .06 Flat
Position: 6
1 COVER, Steering Shaft
Position: 6
2 WING, Rear
Position: 6
1 BEARING, Axle (R. H. Fender) (used on Briggs model)
Position: 6
1 ASSEMBLY, Axle Bearing-DX (R. H. Fender) (incl. two DX Bearings, p/n 7074183) (used on
Position: 6
2 O-RING, 1/2 x 5/8”
Position: 6
4 BOLT, 5/16-18 x 1/2” Hex Flange Nyloc
Position: 6
1 GUARD, Main Case, Front, Euro RER
Position: 6
1 WASHER, 3/8” Flat SAE
Position: 6
1 SPRING, Latching
Position: 6
1 DECAL, 33 Inch (Hi-Vac)
Position: 6
1 INTERLOCK MODULE, Briggs & Kohler
Position: 6
1 INTERLOCK MODULE, Briggs
Position: 6
1 COTTER PIN, 5/32 x 1”
Position: 7
1 PIN, 3/16 x 1” Cotter
Position: 7
2 BOLT, 5/16-18 x 3/4” Hex Flange Lock, GR
Position: 7
1 WASHER, Thrust (1.37” ID, 1.625” OD)
Position: 7
1 WASHER, Shim .625 x .875
Position: 7
1 GUARD, Manifold, RER
Position: 7
2 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
Position: 7
1 SPINDLE, Rider (10.327” overall length)
Position: 7
1 BAND, Brake (Formed)
Position: 7
3 SCREW, 3/8-16 x 5/8” Hex Washer Self-Tap
Position: 7
1 DECAL, Battery Caution, Multi-Language
Position: 7
1 DECAL, Battery Orientation, Euro RER
Position: 7
1 HARNESS, (Deck Interlock Wiring)
Position: 7
1 HUB CAP
Position: 8
2 WASHER, .66 x 1.31 x .09 Flat
Position: 8
2 WASHER, 11/32” Flat
Position: 8
4 BOLT, 5/16-24 x 1-5/8” Hex Special Lock (Vibresist) (replace after each use)
Position: 8
1 KEY, #5 Woodruff
Position: 8
1 SCREW, 1/4-20 x 1” Hex Head Cap, GR
Position: 8
1 GUARD ASSEMBLY, Wire Form (Euro)
Position: 8
1 WASHER, .77 x 1.13 x .06 Flat
Position: 8
4 WASHER, .28 x .63 x .06 Flat, GR 5 (or 7090055)
Position: 8
2 SCREW, 5/16-18 x 1/2” Hex Washer Self-Tap
Position: 8
1 DECAL, Back-Up Recoil (33” Kohler Engine Models)
Position: 8
1 DECAL, OHV (33” Kohler Engine Models)
Position: 8
1 DECAL, Engine, B&S E10 Powerbuilt
Position: 8
1 FELT SEAL
Position: 9
1 BUSHING, Nylon
Position: 9
1 BUMPER, (1-Piece)
Position: 9
1 PLATE, Differential (Note: 4 holes offset - align properly to prevent binding.)
Position: 9
1 WELDMENT, Sprocket & Shaft
Position: 9
3 SCREW, 1/4-20 x 5/8” Hex Head w/Free Spinning Washer
Position: 9
2 SCREW, 3/8-16 x 3/4” Hex Washer Self-Tap, BZ
Position: 9
1 WASHER, Spindle
Position: 9
1 BUSHING, Flange .27 x .35 x .4
Position: 9
1 BRACE, Top
Position: 9
1 DECAL, Caution, Fuel Leakage (English)
Position: 9
1 DECAL, Caution, Fuel Leakage (Dutch)
Position: 9
1 DECAL, Caution, Fuel Leakage (French)
Position: 9
1 DECAL, Caution, Fuel Leakage (German)
Position: 9
1 DECAL, Caution, Fuel Leakage (Symbols)
Position: 9
1 DECAL, Caution, Fuel Leakage (Italian)
Position: 9
1 DECAL, Caution, Fuel Leakage (Spanish)
Position: 9
1 COVER, Battery Cable
Position: 9
1 CAP, Dust
Position: 10
1 HOLDER, Bottle (Wire)
Position: 10
4 SCREW, 3/8-16 x 5/8” Hex Washer Self-Tap
Position: 10
4, 8 SPACER, Pinion
Position: 10
2 WASHER, Thrust, Nylon
Position: 10
1 BRACKET, Muffler Guard (Kohler)
Position: 10
1 SCREW, 1/4-20 x 3/4” Hex Head Flange, GR 5, YZ
Position: 10
2 SCREW, 1/2-20 x 1-1/4” Hex Head Cap, GR
Position: 10
1 SPRING, Rectangular Wire Die, Blue
Position: 10
1 GUIDE, Belt
Position: 10
1 DECAL, Deflector, French/German
Position: 10
1 DECAL, Deflector Caution (English/Dutch)
Position: 10
1 DECAL, Blade Caution, Euro RER
Position: 10
1 WIRE, Positive (Red, 17” long)
Position: 10
1 TUBE, Inner (For 4.10/3.50 x 4 Tire)
Position: 11
2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap (Torx)
Position: 11
4 SCREW, 5/16-18 x 1-1/2” Hex Washer Self-Tap (or 7090484)
Position: 11
4, 8 GEAR, Differential Pinion (12T 12P)
Position: 11
2 BEARING, Needle 1.355” ID x 1.6245” OD x .5” Wide
Position: 11
1 MUFFLER GUARD, Kohler
Position: 11
2 SCREW, 1/4-20 x 1” Hex Washer Self-Tap
Position: 11
2 NUT, 1/2-20 Hex, GR 5 or B
Position: 11
1 NUT, 1/4-20 Hex Top Lock (or 7091705)
Position: 11
1 ANCHOR
Position: 11
1 DECAL, Brake Operation (German)
Position: 11
1 DECAL, Brake Operation (French)
Position: 11
1 DECAL, Brake Operation (Dutch)
Position: 11
1 DECAL, Brake Operation (Italian)
Position: 11
1 DECAL, Brake Operation (Spanish)
Position: 11
1 SWITCH, Ignition, 4 Terminal, Indak
Position: 11
1 SWITCH, Ignition-Afterfire Solenoid
Position: 11
3 BOLT, 1/2-20 x 3/4” Lug, GR
Position: 12
1 BOTTLE, Water
Position: 12
1 COVER, Battery
Position: 12
1 WELDMENT, Hub & Sprocket
Position: 12
1 HOLDER, Blade
Position: 12
1 PIN, 1/4 x 1-5/8” Clevis
Position: 12
2 WASHER, 5/16” Internal Tooth Lock
Position: 12
1 DECAL, Clutch Brake
Position: 12
1 WASHER, 5/8” Internal Tooth Lock
Position: 12
1 HUB CAP, R.H. (1.35” ID x 2.25”) (Short Axle)
Position: 13
1 COVER, Solenoid
Position: 13
1 ASSEMBLY, Short Axle, 23T (Includes Gear)
Position: 13
1 MUFFLER, (Kohler 14 & 15HP)
Position: 13
1 SPACER, Blade Centering
Position: 13
3 PIN, 3/32 x 3/4” Cotter (or 7090037)
Position: 13
2 NUT, 5/16-24 Hex (replaces 7090223 (voided))
Position: 13
1 DECAL, Euro Community (CE)
Position: 13
1 NUT, 5/8-32 Hex
Position: 13
1 HUB, Wheel LH, 3 Hole 3/4” ID (per left rear tire ass'y)
Position: 14
1 HAIR PIN 2-1/4”
Position: 14
7 FASTENER, 1/4” Ratchet
Position: 14
1 SPACER, Differential (1.25” ID x .423 Wide) (was 7011026)
Position: 14
1 GASKET, Primary Chain Case
Position: 14
3 SPACER, .33 x .63 x .156
Position: 14
1 NUT, 5/8-18 Hex Center Lock Jam
Position: 14
1 EYE-BOLT, 1/4-20 x 4”
Position: 14
2 SCREW, 5/16-24 x 3/4” Hex Head Cap, GR
Position: 14
1 DECAL, European Noise Control (100 dB)
Position: 14
1 DECAL, European Noise Control (98 dB)
Position: 14
1 IGNITION KEY, Pair
Position: 14
1 KEYS, Blister Pk (KIDS+MWRS DON'T MIX) English/French (set of two, one coated)
Position: 14
1 HUB, Wheel RH, 3 Hole 1” ID (per right rear tire ass'y)
Position: 15
1 SPRING, Parking Brake Latch
Position: 15
1 BRACKET, Belt Adjuster
Position: 15
1 KIT, Long Axle (Includes welded Gear and item #14) (was 7047763)
Position: 15
1 PRIMARY CHAIN CASE HALF, Left Hand
Position: 15
2 NUT, 1/4-20 Hex Flange Lock
Position: 15
2 SCREW, 1/4-20 x 3-1/2” Hex Head w/Free Spinning Washer
Position: 15
1 SPACER, .39 x 1.0 x .31 Nylon
Position: 15
2 SPRING, Assist
Position: 15
1 DECAL, No Mow in Reverse (Euro)
Position: 15
3 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
Position: 15
3 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap (or 7091122)
Position: 15
1 BOLT, 5/16-24 x 1-5/8” Tapered (Left Hand) (per left rear tire ass'y)
Position: 16
1 RING, 1/2” External Retaining (Heavy Duty)
Position: 16
1 TIE ROD, (5/16-24 thread- both ends)
Position: 16
1 WASHER, Thrust, (Hex Flanged)
Position: 16
2 WASHER, 5/8” Belleville
Position: 16
1 PLATE, Engine (Kohler Engine) (used on Kohler Engine Models only)
Position: 16
4 SCREW, 1/4-20 x 5/8” Hex Head w/Free Spinning Washer
Position: 16
1 DRUM, Brake Spindle (3” OD, 1.6” Tall)
Position: 16
1 BOLT, #10-24 x 1” Flat Head Square Neck
Position: 16
1 DECAL, Deck/Chute International Warning
Position: 16
1 CABLE TIE, 3.19” long
Position: 16
1 BOLT, 5/16-24 x 2” Tapered (Right Hand) (per right rear tire ass'y)
Position: 17
2 RING, 5/8” External Retaining
Position: 17
1 BUSHING, Pivot
Position: 17
1 * ASSEMBLY, Drive Hex Tube
Position: 17
1 PLUG, 3/4” Cup Insert
Position: 17
8 WASHER, .32 x .58 x .08 Split Lock
Position: 17
1 COVER, Spindle
Position: 17
2 RING, 2” External Retaining
Position: 17
1 NUT, #10-24 Hex Nyloc
Position: 17
1 DECAL, Service Parts, Euro
Position: 17
4 NUT, 1/4-20 Hex
Position: 17
1 HARNESS WIRE, Operator Presence Control (OPC)
Position: 17
1 NUT, Hex Lock 5/16F GR.C YZ (was 7011201 (per rear tire ass'y))
Position: 18
6 WASHER, .77 x 1.13 x .06 Flat
Position: 18
1 BRACKET, Switch
Position: 18
1 WASHER, Nylon
Position: 18
1 SCREW, 1/4-28 x 1” Hex Head Cap, (Washer Face) GR
Position: 18
4 NUT, 5/16-24 Hex, GR
Position: 18
1 PIN, Hinge
Position: 18
1 SPRING, Extension, 4” x 1/2” Diameter
Position: 18
2 RING, Rear Lift Arm (Blue)
Position: 18
1 DECAL, Remove Battery, Symbols, Euro
Position: 18
2 WASHER,1/4” Internal Tooth Lock
Position: 18
2 WASHER, 1/4” Internal Tooth Lock
Position: 18
1 HUB CAP, L. H. (.975” ID x 2.25”) (Long Axle) (per left rear tire ass'y)
Position: 19
4 BEARING, Nylon
Position: 19
2 SCREW, #10-32 x 1/4” Hex Washer Self-Tap
Position: 19
2 O-RING, 5/16”
Position: 19
2 WASHER, .28 x .63 x .06 Flat, GR
Position: 19
4 BOLT, M8-1.25 x 25mm, Self-Tap (Kohler)
Position: 19
3 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR 5 (or 7091510)
Position: 19
1 WELDMENT, Idler Arm
Position: 19
1 PIVOT, Leveling
Position: 19
2 SCREW, 1/4-20 x 5/8” Hex Head Cap, GR
Position: 19
2 SCREW, 1/4-20 x 5/8” Hex Head Cap GR 5 (or 7090072)
Position: 19
2 CLAMP, Boot, 2” (used on older models)
Position: 20
2 FOOT PAD, (Wide)
Position: 20
2 SCREW, 5/16-24 x 1” Hex Head Cap, GR
Position: 20
2 WASHER, 5/16” Belleville
Position: 20
1 SPACER, Brake Arm Pivot (.418/.403 long) (replaces 7010916 (.300/.285 long))
Position: 20
4 SCREW, 5/16-24 x 1” Hex Head Cap, GR
Position: 20
1 SPRING, Hinge
Position: 20
1 SCREW, 3/8-16 x 1-1/2” Hex Head Cap, GR
Position: 20
1 WIRE, Negative, Black (15” long)
Position: 20
1 SEAL, 1.22” ID x 1.875” OD (used on older models)
Position: 21
2 NUT, 5/16-24 Hex Center Lock
Position: 21
1 GEAR, 11 Tooth, 10 Pitch (replaces 7010964)
Position: 21
1 ASSEMBLY, Brake Lever (Includes brake pad & rivet)
Position: 21
1 BELT GUIDE, K 30/33” (used on all Kohler 33” Euro Models)
Position: 21
1 HINGE, Deflector (Deck side)
Position: 21
1 RESTRICTOR, Belt
Position: 21
1 NUT, 3/8-24 Hex Nyloc
Position: 21
1 HARNESS, Operator Presence Control (OPC) Wire
Position: 21
2 NUT, 1/4-20 Hex, GR 5 or B (attaches to starter terminal)
Position: 21
1 CAP, Seal 1.0” ID x 1.67” OD (used on older models)
Position: 22
1 PAD, Pedal
Position: 22
1 LIFT, Yoke
Position: 22
1 SPROCKET, 34T, 3/8P
Position: 22
1 RING, 3/8” External Retaining
Position: 22
4 SCREW, 5/16-24 x 1-3/4” Hex Head Cap, GR
Position: 22
2 PUSH NUT, 1/4”
Position: 22
2 PULLEY, Idler (3/8” ID, 4” OD)
Position: 22
1 WELDMENT, Rear Lift Arm
Position: 22
1 NUT, 1/4-20 Hex, GR 5 or B
Position: 22
1 SEAL, OIL .750” ID x 1.832” OD (used on older models)
Position: 23
1 CABLE, Clutch/Brake (55” long)
Position: 23
1 COLLAR, Yoke
Position: 23
1 RING, 1-3/16” External Retaining
Position: 23
1 * SPRING, Torsional Brake Return
Position: 23
2 NUT, 5/16-18 Hex Flange Lock, GR
Position: 23
9 NUT, 5/16-18 Hex Flange Lock, GR
Position: 23
2 WASHER, 3/8” Flat
Position: 23
2 ADJUSTER, Chain (5/16-18 thread)
Position: 23
2 CABLE TIE, 7”
Position: 23
1 CAP, Seal 3/4” ID x 1.875” OD (used on older models)
Position: 24
1 CABLE, Brake, Snap-In (replaces 7072648 (voided))
Position: 24
2 BEARING, Yoke
Position: 24
1 CHAIN, 46 Pitch (#35 Endless)
Position: 24
1 NUT, 1/4-28 Hex Top Lock
Position: 24
1 MUFFLER w/Guard (Briggs 17.5HP)
Position: 24
1 DEFLECTOR, Discharge, 28” & 33”
Position: 24
2 NUT, 3/8-16 Hex Nyloc
Position: 24
2 NUT, 1/4-20 Hex Center Lock, GR 5 or B
Position: 24
1 NUT, 1/4-20 Hex Center Lock, GR 5 or B
Position: 25
2 FENDER WASHER, 5/16”
Position: 25
1 SPACER, Differential Case
Position: 25
1 ASSEMBLY, Smooth Clutch (non-asbestos) (Includes the following 5 items)
Position: 25
1 SCREW, 1/4-20 x 5/8” Hex Washer Head Self-Tap
Position: 25
1 DECAL, Danger, (Cut Finger) International Symbol
Position: 25
1 SCREW, #10-32 x 1” Hex Washer Head Self-Tap
Position: 25
2 RETAINER, 1/4” Bolt
Position: 25
2 CONNECTOR, Cable
Position: 26
1 SPRING, Clutch & Brake
Position: 26
1 CASE, Transmission
Position: 26
1 HUB, Driven Disc (assembly) (replaces 7054243 (voided))
Position: 26
1 GASKET, Exhaust
Position: 26
2 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR 5 (or 7090001)
Position: 26
1 SWITCH, Deck Interlock (NO)
Position: 26
1 GRIP, Height Adjustment Lever
Position: 26
1 SCREW, 1/4-20 x 3/4” Hex Head Cap, GR
Position: 27
1 PIN, 3/32 x 3/4” Cotter (or 7090037)
Position: 27
2 PLUG, 1/2” Cup Insert
Position: 27
1 DISC, Driven (rubber tire bonded to rim)
Position: 27
1 ASSEMBLY, Oil Valve
Position: 27
2 WASHER, 5/16” Flat ( or 7091296)
Position: 27
1 MOUNT, Handle/Switch
Position: 27
1 LEVER, Height of Cut
Position: 27
1 SWITCH, Operator Presence Control (OPC) Traction (NC/NO)
Position: 27
1 TUBE CLAMP
Position: 28
2 WASHER, 3/8” Flat SAE
Position: 28
1 WASHER, 5/16” External Tooth Lock
Position: 28
1 WASHER, Thrust
Position: 28
2 SET SCREW, 5/16-18 x 3/4” Socket Head, GR8
Position: 28
2 NUT, 5/16-18 Wing
Position: 28
1 ROD, Idler Control
Position: 28
1 SPRING, Lever
Position: 28
1 SCREW, 5/16-24 x 2-1/2” Hex Head Cap, GR
Position: 29
1 BRACKET, Slide
Position: 29
1 WASHER, .34 x .69 x .08 Flat
Position: 29
1 PLATE, Drive Disc
Position: 29
1 ASSEMBLY, Fuel Tank with Gauge (Includes Cap)
Position: 29
2 BRACKET, Gage Wheel (Rear)
Position: 29
1 SPRING, Blade Handle
Position: 29
1 SCREW, 3/8-24 x 1-3/4” Hex Head Cap, GR
Position: 29
1 NUT, 5/16-24 Flange Lock (Large)
Position: 30
1 BOLT, 5/16-18 Shoulder
Position: 30
1 SCREW, 5/16-24 x 2-5/8” Hex Head Cap
Position: 30
4 NUT, 5/16-24 Hex Flange Lock
Position: 30
1 CAP, Fuel Tank w/Gage
Position: 30
3 SPACER
Position: 30
1 WELDMENT, Blade Engagement Handle
Position: 30
2 WASHER, 13/32 x 1-1/4” Flat
Position: 30
1 BUSHING, Nylon
Position: 31
2 SLIDE HALF
Position: 31
1 BOOT, Oil Seal (Short Axle)
Position: 31
1 NUT, 5/8-18 Hex Nyloc
Position: 31
4 CLAMP, Fuel Line (.490 X .31)
Position: 31
3 WHEEL, Gage
Position: 31
1 SPRING, Torsion, Flip Handle
Position: 31
2 SPACER, Deck Lift
Position: 31
1 WELDMENT, Steering Shaft
Position: 32
6 NUT, 5/16-18 Hex Flange Lock, GR
Position: 32
2 BOOT CLAMP, 2”
Position: 32
1 qt ** GREASE, Transmission (Use 2 oz. Maximum)
Position: 32
1 HOSE, Fuel (1/4” I.D. x 8-1/2” long) (used on 7800718 model)
Position: 32
1 HOSE, Fuel (1/4” I.D. x 12-1/2” long) (used on Kohler Models only)
Position: 32
1 HOSE, Fuel (1/4” I.D. x 6-1/2” long) (used on Kohler Models only)
Position: 32
3 SCREW, 3/8-24 x 3-3/4” Hex Head Cap, GR
Position: 32
1 PIN, 3/16 x 1” Clevis
Position: 32
1 NUT, 3/8-24 Hex Center Lock
Position: 32
1 PIN, 3/16 x 1-1/2” Cotter
Position: 33
1 BRACKET, Drive Support
Position: 33
1 GRIP, Shift Handle
Position: 33
1 HOSE, Fuel (1/4” I.D. x 3-1/2” long)
Position: 33
3 NUT, 3/8-24 Hex Nyloc
Position: 33
1 PIN, 3/32 x 1/2” Cotter
Position: 33
1 SPACER, Detent
Position: 33
4 WASHER, 3/8” Flat SAE (or 7091514)
Position: 34
1 WASHER, 5/16” Split Lock
Position: 34
1 WELDMENT, Shift Handle
Position: 34
1 VALVE, Fuel Shut-Off (Accessory)
Position: 34
1 BRACKET, Gage Wheel (Front)
Position: 34
1 HANDLE, Blade Engagement (Flip)
Position: 34
1 DETENT, Height Adjust
Position: 34
1 WELDMENT, King Pin, Left Hand
Position: 35
1 NUT, 5/16-18 Hex, GR 5 or B
Position: 35
1 PIN, 3/32 x 3/4” Cotter (or 7090037)
Position: 35
1 FILTER, Fuel (In-Line)
Position: 35
1 COVER, 33” Mulcher (optional)
Position: 35
1 GRIP, Handle
Position: 35
2 SCREW, 3/8-16 x 1” Hex Washer Self-Tap
Position: 35
1 WELDMENT, King Pin, Right Hand
Position: 36
1 STUD, Clutch Link (3/8-24 thread)
Position: 36
1 PIN, 1/4 x 1-3/4” Tapered Clevis
Position: 36
6 BOLT, 5/16-18 x 1/2” Short Neck Carriage, GR
Position: 36
2 SCREW, 1/4-20 x 5/8” Hex Washer Head Self-Tap (or 7091819)
Position: 36
1 CABLE ASSEMBLY, No Reverse in Mow
Position: 36
4 BUSHING, Tie Rod
Position: 37
1 ARM, Yoke
Position: 37
2 WASHER, Thrust (.76” ID, 1.63” OD)
Position: 37
2 SCREW, 5/16-18 x 1/2” Pan Head Self-Tap (Torx #T-40)
Position: 37
3 BOLT, 3/8-16 x 3/4” Hex Flange Lock
Position: 37
5 SCREW, 5/16-18 x 1/2” Hex Washer Self-Tap
Position: 37
1 RING, .438 External Retaining
Position: 37
1 TIE ROD, Left Hand (9.91” long)
Position: 38
1 WASHER, 3/8” Internal Tooth Lock
Position: 38
1 BUSHING, 3/4 x 1.62 Flange (Nylon)
Position: 38
4 WASHER, 11/32” Flat
Position: 38
2 NUT, 1/2-20 Hex Jam
Position: 38
1 BRACKET, Fixed Idler
Position: 38
2 RING, Front Lift Arm (Red)
Position: 38
1 TIE ROD, Right Hand (9.91” long)
Position: 39
1 NUT, 3/8-24 Hex, GR 5 or B (or 7090155)
Position: 39
1 NUT, 5/16-18 Hex Nyloc
Position: 39
1 PLATE, Throttle Control
Position: 39
2 WASHER, 1/2” Internal Tooth Lock
Position: 39
1 BRACE, Fixed Idler Bracket
Position: 39
1 WELDMENT, Front Lift Arm
Position: 39
2 PIN, 5/32 x 1” Cotter
Position: 40
1 ASSEMBLY, Leaf Spring
Position: 40
1 ** ASSEMBLY, Speed Adjustment Latch
Position: 40
1 CONTROL, Throttle (23.6” long) (Briggs Engines)
Position: 40
1 CONTROL, Throttle (34.6” long) (Kohler Engines)
Position: 40
1 RING, Tolerance
Position: 40
1 SPACER, Idler
Position: 40
1 PIN, 1/8 x 3/4” Cotter (or 7090365)
Position: 40
2 PIN, 1/8 x 3/4” Cotter
Position: 41
2 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
Position: 41
1 SPRING (part of Speed Adjustment Latch Ass'y)
Position: 41
9 NUT, 3/8-16 Hex Flange Lock (or 7090585)
Position: 41
1 GUARD, Pulley (used on 7800119)
Position: 41
1 ROD, Leveling (3/4-24 thread)
Position: 41
2 CAP, Dust
Position: 42
4 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap (or 7091867)
Position: 42
1 NUT, 5/16-18 Hex, GR 5 or B
Position: 42
2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap (Torx)
Position: 42
2 SCREW, 1/2-20 x 1” Hex Head Cap, GR
Position: 42
1 SCREW, 3/8-16 x 2” Hex Head Cap, GR
Position: 42
1 NUT, 3/8-24 Hex, GR B (or 7090155)
Position: 42
1 WASHER, 5/16” Internal Tooth Lock
Position: 43
1 SPRING, Shift Detent
Position: 43
1 WELDMENT, 5.25” O.D. Drive Disc
Position: 43
1 BLADE, 33”
Position: 43
1 WASHER, Flat 13/32” ID x 1.25” x 1/8” Thick ZP (or 7012063)
Position: 43
1 CLIP, Wire
Position: 44
1 BUSHING, 3/4 x I.O. Flange (Nylon)
Position: 44
2 SET SCREW, HRSS, 3/8-16 x 3/8”
Position: 44
1 BLADE, 33” Mulcher
Position: 44
1 ARM, Front Lift
Position: 44
3 NUT, 5/16-24 Flange Lock (Large)
Position: 45
1 WELDMENT, Arm, Shift Handle (w/grease fitting. Hole)
Position: 45
1 KEY, 1/4” Square x 2” Long
Position: 45
1 BLADE, Ninja, 33”
Position: 45
1 ROD, Deck Support (Front Lift Arm to Front End)
Position: 45
2 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR 5 (or 7090206)
Position: 46
1 LUBE FITTING, 3/16” Press-In
Position: 46
1 KIT, Air Lift, Hi-Vac (Includes items 47, 48, 49 & 50)
Position: 46
1 BOLT, Shoulder, 3/8-24 x 9/16”
Position: 46
2 BOOT CLAMP, 2”
Position: 47
1 WASHER, .32 x .58 x .08 Split Lock
Position: 47
2 NUT, 5/16-18 Hex Flange Top Lock
Position: 47
2 AIR LIFT, Hi-Vac (3 hole)
Position: 47
2 WASHER, 1/2” Flat SAE (or 7090250)
Position: 47
1 BOOT, Rear Axle, Thick Flange
Position: 48
1 NUT, 5/16-24 Hex, GR
Position: 48
2 KNOB, Fluted, 5/16-18 internal thread (2.15 O.D.)
Position: 48
6 SCREW, 5/16-24 x 11/16” Oval Head Machine
Position: 48
1 SPRING, Pedal
Position: 48
1 WASHER, Thrust, (Hex Flanged)
Position: 49
1 LEVER, Over-Ride
Position: 49
1 NUT, 1/4-20 Hex, GR 5 or B (not shown) (attaches to starter terminal)
Position: 49
6 WASHER, 5/16” Internal Tooth Lock
Position: 49
1 FOOT PEDAL, Blade Stop Control
Position: 49
1 WASHER, Thrust, (.765” ID, 1.625” OD)(Nylon)
Position: 50
1 WASHER, .47 x .92 x .065 Flat
Position: 50
6 NUT, 5/16-24 Hex
Position: 50
1 WASHER, Shim (Nylon, can make from 7011071) (or quantity as required)
Position: 51
1 BOLT, Shoulder, 5/16-18
Position: 51
1 NUT, 1/4-20 Hex Flange Lock, GR
Position: 51
1 CROSS BRACE
Position: 52
1 CLIP, Cable
Position: 52
1 WELDMENT, Shift Arm
Position: 53
1 BOLT, 1/4-20 x 3/4” Square Neck Carriage, GR
Position: 53
1 SHIFT LINK, Long (5/16-24 both ends)
Position: 54
1 BOLT, Shoulder, 3/8-24 w/Nylon Patch, GR
Position: 54
1 SHIFT LINK, Short (5/16-24 thread)
Position: 55
7 WASHER, .32 x .58 x .08 Split Lock
Position: 56
7 NUT, 5/16-24 Hex, GR
Position: 57
1 ASSEMBLY, DX Bearing (incl. items 59-61)
Position: 58
2 BEARING, DX, 3/4” ID
Position: 59
1 FITTING, Lube, 45 Degree, 3/16” w/Hex (long shank) (or 7013324)
Position: 60
1 SEAL, Axle (Dust/Grease)
Position: 61
1 KIT, Tire Chains (16 x 4.50-8 Tires) (used on All Rear Engine Riders)
Position: 7060049
1 KIT, Drive Disc Puller (used on All RER Aluminum Drive Discs)
Position: 7060325
1 KIT, Tire Chains (16 x 6.50-8 Tires) (used on All Rear Engine Riders)
Position: 7060653
1 KIT, Dump Cart (used on All Rear Engine Riders)
Position: 7060697
1 KIT, Gage Wheel (used on All 33” Deck Rear Engine Riders)
Position: 7060737
1 KIT, Single Bag Catcher (used on All 25” Deck Rear Engine Riders)
Position: 7060941
1 KIT, Single Bag Catcher (used on All 28” & 33” Deck Rear Engine Riders)
Position: 7060943
1 KIT, Bag-N-Wagon (used on All 28” & 33” Deck Rear Engine Riders)
Position: 7060947
1 KIT, 28” Thatcherizer (used on All series 7 & Newer Rear Engine Riders)
Position: 7060948
1 KIT, 36” Dozer Blade (used on All Rear Engine Riders)
Position: 7060959
1 KIT, Wagon Cover (used on All 28” & 33” Deck Rear Engine Riders)
Position: 7060964
1 KIT, Ninja Recycling Cover (used on All 25” Deck Rear Engine Riders)
Position: 7061049
1 KIT, Ninja Recycling Cover (used on All 28” Deck Rear Engine Riders)
Position: 7061253
1 KIT, Ninja Recycling Cover (used on All 33” Deck Rear Engine Riders)
Position: 7061255
1 HARDWARE BAG (Seat attachment & steering hdwe.) (used on model E281123BVE)
Position: 7061872
1 HARDWARE BAG (Seat attachment & steering hdwe.) (used on model E2512523BVE)
Position: 7063039
1 KIT, Twin Bag Catcher (used on All 28” & 33” Deck Rear Engine Riders)
Position: 7063281
1 HARDWARE BAG (Seat attachment & steering hdwe.) (used on models E2812523BVE,
Position: 7063292
1 KIT, Front Weight (used on All series 7 & Newer Rear Engine Riders)
Position: 7072416