Exploderad vy Fischer sn250ztwin-2007-snapper
Upptäck den fullständiga exploderade vyn Fischer sn250ztwin-2007-snapper – en oumbärlig guide för att identifiera reservdelar. Vår presentation hjälper dig förstå varje komponent i din . Hitta snabbt delarna till din Fischer sn250ztwin-2007-snapper.
Reparationsassistent
Powered by ChatGPT
Lista över reservdelar
2 ASSEMBLY, Front Wheel & Tire
Position: 1
1 FRONT AXLE, Cast (Cardinal Red)
Position: 1
1 FRAME, RZT (Cardinal Red)
Position: 1
1 WELDMENT, Transaxle Support
Position: 1
1 HANDLE
Position: 1
1 FENDER, LH RZT
Position: 1
1 ASSEMBLY, 15” Seat, w/Armrests Ref. Michigan Seat Co.
Position: 1
1 * ENGINE, 18.5 HP B&S Intek Mod. 31P777-0122-B1, Euro RZT
Position: 1
1 * ENGINE, 20 HP Briggs Mod. 40G777-0184-E1 Extended Life
Position: 1
1 * ENGINE, 22 HP Briggs Mod. 441777-0117-B1 Intek Twin
Position: 1
1 GRIP
Position: 1
1 WELDMENT, 44” Deck- Simplicity finish: Cardinal Red
Position: 1
2 COTTER PIN, 1/2 Self Locking, YZ
Position: 1
1 WELDMENT, 50” Mower Deck, SNAPPER
Position: 1
1 DECAL, Ignition, RZT
Position: 1
1 DECAL, SNAPPER FENDER, RH
Position: 1
1 SOLENOID - Super Trombetta - 2 Terminal
Position: 1
1 WIRING HARNESS, Briggs RZT
Position: 1
1 RIM, Caster Wheel
Position: 2
3 LUBE FITTING, 3/16” Press-In
Position: 2
12 NUT, 5/16-18 Hex Flange Lock, GR
Position: 2
2 ROD, Roll Release
Position: 2
1 WELDMENT, LH Control Arm (5/8” dia. Rod)
Position: 2
1 ROD, Handle R.H. (5/8” dia. Rod)
Position: 2
1 R. H. CONTROL ARM (5/8” dia. Rod)
Position: 2
1 NUT, 5/16-18 Hex Nyloc
Position: 2
1 FENDER, RH RZT
Position: 2
1 SEAT PLATE
Position: 2
4 SCREW, 3/8-16 x 1” Hex Washer Self-Tap
Position: 2
3 SCREW, 3/8-16 x 1” Hex Washer Self-Tap
Position: 2
1 HANDLE, Deck Lift
Position: 2
3 GROUP, 44” Spindle, ERZT includes items 3 thru 11, 12A,
Position: 2
2 ROD, Stabilizer
Position: 2
3 GROUP, 50” Spindle, RZT
Position: 2
1 DECAL, Snapper Fender, RH
Position: 2
1 DECAL, SNAPPER FENDER, LH
Position: 2
2 SCREW, 1/4-20 x 1” Hex Head Cap, GR
Position: 2
1 CABLE, Battery Positive RZT, Red 20" #6 AWG
Position: 2
1 TIRE, 11 x 4.00-5, Smooth Tread
Position: 3
2 WELDMENT, Caster (Cardinal Red)
Position: 3
1 TANK BRACKET
Position: 3
2 WASHER, .28 x .63 x .06 Flat, GR
Position: 3
1 FOAM GRIP, Handle
Position: 3
2 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR
Position: 3
2 KNOB, Three Prong, 5/16-18 thread
Position: 3
1 ASSEMBLY, Engine Pulley
Position: 3
2 BOLT, 3/8-16 x 3/4” Hex Flange Lock, GR 5, YZ
Position: 3
3 * NUT, 3/4-16 Hex Jam, GR
Position: 3
1 DECAL, Snapper Fender, LH
Position: 3
6 NUT, 1/4-20 Hex Flange Lock, GR
Position: 3
1 WIRING HARNESS, Hour Meter, RZT
Position: 3
2 BALL BEARING, .625 x 1.38
Position: 4
4 THRUST WASHER, 1” I.D.
Position: 4
4 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR
Position: 4
2 HAIR PIN, 1-1/8”
Position: 4
2 BUSHING, Bronze, 5/8 x 5/8”
Position: 4
4 BUSHING, Bronze, 5/8 x 5/8”
Position: 4
1 BRACKET, Park Brake, LH Lower
Position: 4
4 BOLT RETAINER, 5/16” Black
Position: 4
2 WASHER, 5/16” Split Lock
Position: 4
1 KEY, 1/4 Square x 1”
Position: 4
1 RETAINING RING, 5/8”, External
Position: 4
6 * WASHER, .77 x 1.5 x .06 Flat case hardened steel
Position: 4
4 NUT, 7/16-20 Hex, GR 5 or B
Position: 4
1 DECAL, SNAPPER
Position: 4
1 12 VOLT DC POWER OUTLET
Position: 4
2 WIRE, Negative, Black 14" #8 AWG
Position: 4
1 GREASE FITTING, 1/4-28 thread forming Alemite #3038-B
Position: 5
2 RETAINING RING, 1” External
Position: 5
1 FOOTREST, Snapper (Cardinal Red)
Position: 5
8 SCREW, 5/16-18 x 3/4” Hex Washer Self-Tap
Position: 5
1 WELDMENT, Control Arm, LH
Position: 5
4 NUT 1/4-20 Hex Center Lock, GR 5 YZ
Position: 5
1 CONTROL ARM, LH, Die Cast
Position: 5
2 NUT, 5/16-18 Hex Flange Lock, GR
Position: 5
4 NUT, 5/16-18 Hex Large Flange Center Lock
Position: 5
1 BRACKET, Seat Support
Position: 5
1 CLUTCH, Ogura JD-11
Position: 5
3 * PULLEY, 4-3/4” O.D.
Position: 5
4 WASHER, 7/16” Split Lock
Position: 5
1 DECAL, Throttle Control, RZT
Position: 5
2 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap
Position: 5
1 VALVE STEM, Snap In
Position: 6
1 SCREW, 1/2-13 x 3-1/2” Hex Head Cap, YZ
Position: 6
6 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR
Position: 6
2 SHOULDER BOLT, 5/16-18 .530 long shoulder
Position: 6
1 WASHER, 5/8 ID x 1.00 OD x .065 Nylon
Position: 6
1 WASHER, .64 x .99 x .05 Flat, YZ
Position: 6
1 COTTER PIN, 3/8” Self-Locking
Position: 6
1 COVER, Front, Snapper
Position: 6
2 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5, YZ
Position: 6
1 WASHER, .468 ID x 1.50 OD x .188 Flat
Position: 6
2 COTTER PIN, 1/2”, Self-Locking was
Position: 6
2 * WASHER, Spindle (Special)
Position: 6
4 WASHER, .47 x .92 x .065 Flat
Position: 6
1 DECAL, Warning, Operation
Position: 6
1 DECAL, Motion Control, Symbols, ERZT
Position: 6
1 HOUR METER, Inductive
Position: 6
2 SCREW, 7/16-14 x 6”, Hex Head Cap, GR
Position: 7
2 WASHER, 1/2” SAE Flat
Position: 7
1 PLATE, Rear Seat Guard
Position: 7
12 NUT, 5/16-18 Hex Nyloc
Position: 7
1 WASHER, 5/8” Flat SAE
Position: 7
2 BUSHING
Position: 7
1 ROD, Park Brake
Position: 7
4 SCREW, 1/4-20 x 5/8” Hex Washer Self-Tap, YZ euro models
Position: 7
2 WASHER, 3/8” Internal Tooth Lock
Position: 7
1 WASHER, 7/16” Split Lock
Position: 7
1 ROD, Link
Position: 7
2 * RING, 1.85” Internal Retaining
Position: 7
2 SCREW, 7/16-20 x 4” Hex Head Cap, GR
Position: 7
1 DECAL, Height Of Cut, RZT
Position: 7
1 DECAL,Deck/Chute International Warning
Position: 7
1 SWITCH, PTO, Yellow
Position: 7
2 TUBE, 5/8 O.D. x 14 Ga. Wall x 4.510” long caster wheel spacer
Position: 8
2 SPACER, Axle Pivot
Position: 8
8 BOLT, 5/16-18 x 7/8” Hex Flange Lock, YZ
Position: 8
1 TRANSAXLE, LH RZT ZA-AHBB-2D5A-2DCX
Position: 8
1 WASHER, .64 x 1.12 x .028 Beveled
Position: 8
1 WELDMENT, Control Arm, RH
Position: 8
1 CONTROL ARM, RH Die Cast
Position: 8
1 BRACKET, Park Brake, RH Lower
Position: 8
1 PANEL, Control
Position: 8
2 NUT, 3/8-16 Hex Flange Lock
Position: 8
1 SCREW, 7/16-20 x 4-1/2” Hex Head Cap, GR
Position: 8
1 SWIVEL, 3/8” w/thru hole, Special
Position: 8
2 * BEARING, Spindle
Position: 8
7 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR
Position: 8
1 DECAL, Motion Control, RZT
Position: 8
1 DECAL, Safety Symbols- RZT
Position: 8
1 PLUG, Plastic Black
Position: 8
2 NUT, 7/16-14 Hex Center Lock, GR 5 or B
Position: 9
2 BEARING SLEEVE
Position: 9
1 HEAT SHIELD finish: black powder coat
Position: 9
1 TRANSAXLE, RH RZT ZA-DHBB-2D5A-2DCX
Position: 9
2 NUT, 5/8-18 Hex Jam
Position: 9
1 NUT, 5/8-18 Hex Nyloc
Position: 9
1 WASHER, 1/2 x .090 Flat
Position: 9
5 SCREW, 1/4-20 x 5/8” Pan Head Self-Tap (Torx)
Position: 9
2 BOLT, 5/16-18 x 1” Hex Flange Lock, GR 5, YZ
Position: 9
1 HOSE, Oil Drain
Position: 9
1 NUT, 3/8-24 Hex Nyloc
Position: 9
1 * SHAFT, Blade Spindle (6-11/16 overall length) top thread 3/4-16, bottom thread
Position: 9
1 SCREW, 1/4-20 x 2” Hex Head Cap, GR
Position: 9
1 * SHAFT, Blade Spindle (6-11/16” overall length)
Position: 9
1 BAFFLE, Anti-Blowout
Position: 9
1 DECAL, Park Brake, RZT
Position: 9
1 DECAL, Height of Cut, Symbols, ERZT
Position: 9
1 SWITCH, Seat (NC)(Grey)
Position: 9
2 ASS'Y. 18 x 8.50-8 Tire/Wheel, Turf Master, PMS 877 Silver
Position: 10
1 NUT, 1/2-13 Hex Center Lock, GR 5, YZ
Position: 10
2 BRACKET, Body Support
Position: 10
1 BRACKET, Anti-Rotation
Position: 10
1 SHOULDER BOLT, 3/8-16
Position: 10
1 WASHER, 5/8 SAE Flat
Position: 10
1 SCREW, 3/8-16 x 2-3/4” Hex Head Cap, GR
Position: 10
1 WASHER, .531 x 1.0 x .063 Flat
Position: 10
1 U-NUT 1/4-20
Position: 10
2 SPRING, Compression- Seat Support
Position: 10
1 HARNESS CLIP, 5/8”
Position: 10
2 BUSHING, Teflon Impregnated
Position: 10
1 * WELDMENT, Spindle Housing
Position: 10
1 DEFLECTOR, Plastic
Position: 10
1 DEFLECTOR, Black Plastic
Position: 10
1 DECAL, Roll Release, RZT
Position: 10
2 DECAL, Warning, International Symbol
Position: 10
2 SWITCH- DPDT (NC/NO)(Grey)
Position: 10
1 RIM, 18 x 8.50, 4 Bolt
Position: 11
1 BRACKET, Axle (Cardinal Red)
Position: 11
2 SCREW, 5/16-18 x 1” Hex Washer Self-Tap, GR
Position: 11
1 PIN, Anti-Rotation, RZT Clutch
Position: 11
1 THRUST WASHER, .562 ID x 1.000 OD x .030/.032 Thick
Position: 11
1 SHOULDER BOLT, 5/16-18 x 1” .220 long shoulder
Position: 11
1 BRACKET, RH Fender Support (Cardinal Red)
Position: 11
4 NUT, 5/16-18 Hex Nyloc
Position: 11
1 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap, GR
Position: 11
2 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR
Position: 11
1 WELDMENT, Handle Lift yellow zinc plated
Position: 11
1 * LUBE FITTING, 3/16” Press-In
Position: 11
7 NUT, 5/16-18 Hex Flange Lock, GR
Position: 11
1 DECAL, Chute/Deflector
Position: 11
1 DECAL, Roll Release, ERZT
Position: 11
1 BATTERY BRACKET
Position: 11
1 TIRE, 18 x 8.50-8, Turf Master
Position: 12
6 BOLT, 5/16-18 x 7/8” Hex Flange Lock
Position: 12
2 BRACE, Hood/Fender
Position: 12
1 NUT, 5/16-18 Hex Flange Lock, GR
Position: 12
2 FLANGE BEARING, 9/16 I.D. P.M.
Position: 12
1 ROD, Park Brake (1/4-20 thread)
Position: 12
2 BOLT, 5/16-18 x 7/8” Hex Flange Lock, YZ
Position: 12
1 ROD, Seat Hinge
Position: 12
1 CABLE, 26.25” Throttle Control
Position: 12
1 CABLE, 48” Throttle Control B&S 16HP Single Intek
Position: 12
3 NUT, 3/8-16 Hex Flange Lock
Position: 12
1 BAFFLE, Blowout, LH, 44” Mower
Position: 12
1 * BLADE, 18-1/8”
Position: 12
1 SPRING, Idler, 44/50” Deck Ref.
Position: 12
2 DECAL, Danger, (Cut Finger)
Position: 12
1 DECAL, 250 Z 18.5HP RZT
Position: 12
1 DECAL, 250 Z 20HP RZT not shown; similar to
Position: 12
1 BATTERY HOLD DOWN
Position: 12
8 LUG NUT 1/2-20 Tapered Seat YZ
Position: 13
6 NUT, 5/16-18 Hex Flange Lock, GR
Position: 13
2 NUT, 5/16-18 Hex Flange Lock, GR
Position: 13
2 SCREW, 5/16-18 x 1-3/4” Hex Head Cap, GR 5, YZ
Position: 13
2 NUT, 3/8-16 Hex Nyloc
Position: 13
6 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap
Position: 13
2 NUT, 3/8-16 Hex Nyloc or 7091585 (center lock nut)
Position: 13
2 NUT, 3/8-16 Hex Center Lock, GR 5 or B, YZ
Position: 13
1 KNOB, Throttle, Red RZT
Position: 13
2 * WASHER, Beveled
Position: 13
1 BAFFLE, Blowout, 44” Mower
Position: 13
1 DECAL, 250 Z 22HP RZT
Position: 13
1 DECAL, 2006 Year of Mfg.
Position: 13
1 DECAL, 2007 Year of Mfg. not shown; similar to
Position: 13
1 SWITCH, Ignition-Afterfire Solenoid includes set of keys
Position: 13
8 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR
Position: 14
4 SCREW, 5/16-18 x 3” Hex Head Cap, GR 5, YZ
Position: 14
1 SHOULDER BOLT, 5/16 x 1/4-20
Position: 14
1 SCREW, 5/16-18 x 2-3/4” Hex Head Cap, GR
Position: 14
1 SPRING, Compression
Position: 14
1 COVER, Engine, Double Vent
Position: 14
2 SHOULDER BOLT, 5/16-18 x 1” .220 long shoulder
Position: 14
1 SCREW, #10-16 x 3/4” Pan Head Self-Tap
Position: 14
2 SCREW, 1/4-20 x 5/8” Hex Head Cap, GR 5 or
Position: 14
1 * NUT, 5/8-18 Hex Jam
Position: 14
2 RETAINER, 1/4” Bolt
Position: 14
1 DECAL-50”-Silver on black w/stripe
Position: 14
1 DECAL, Park Brake, ERZT
Position: 14
1 MACHINERY BUSHING
Position: 14
20 NUT, 5/16-18 Hex Top Lock, GR B
Position: 15
1 SPRING, Torsion, RH Wind
Position: 15
8 SHIM WASHER, 5/16” I.D.
Position: 15
1 DAMPENER, Hydraulic
Position: 15
1 TRACK, Control Stick, R.H.
Position: 15
1 SPRING, Extension, RTN, ERZT
Position: 15
1 BRACKET, Park Brake
Position: 15
2 WASHER, 1/4” Internal/External Tooth Lock
Position: 15
2 SCREW, 1/4-20 x 5/8” Pan Head Self-Tap (Torx)
Position: 15
1 WELDMENT, Handle Support
Position: 15
18 NUT, 5/16-18 Hex Flange Lock, GR
Position: 15
1 SPACER, .380 ID x .750 OD x .895
Position: 15
17 NUT, 5/16-18 Hex Flange Lock, GR
Position: 15
1 DECAL, OPEI Walk/Ride not shown, not a service part
Position: 15
1 DECAL-44”-Silver on Black w/stripe
Position: 15
1 BEZEL
Position: 15
2 PLATE, Friction
Position: 16
1 WELDMENT, Hydro Idler
Position: 16
4 SCREW 5/16-18 x 2-3/4” Hex Head Cap, GR 5, YZ
Position: 16
1 SPACER, 9/16 OD x 12GA x .325
Position: 16
1 WELDMENT, Lift Bracket
Position: 16
3 SPACER, 9/16” OD x 12GA x .325
Position: 16
2 SPACER, .34 x .63 x .31
Position: 16
2 SCREW, 1/4-20 x 3/4” Hex Head Cap, GR
Position: 16
2 WASHER, 5/16” Split Lock
Position: 16
1 CABLE, 30” Choke Control
Position: 16
1 CABLE, 54” Choke Control
Position: 16
17 BOLT, 5/16-18 x 7/8” Hex Flange Lock, YZ
Position: 16
1 COVER, Spindle, LH, Red, RZT 44/50”
Position: 16
16 BOLT, 5/16-18 x 7/8” Hex Flange Lock, YZ
Position: 16
1 DECAL, Euro Community (CE)
Position: 16
4 WASHER, .28 x .63 x .06 Flat, GR
Position: 16
8 SCREW, 5/16-18 x 1” Flat Head Countersunk
Position: 17
1 SPACER, Hydro Idler
Position: 17
2 BRACKET, Transaxle Support
Position: 17
2 WASHER, 1/4” I.D. Flat
Position: 17
4 WASHER, .33 x .88 x .09 Flat
Position: 17
1 NUT, 1/4-20 Hex Top Lock, GR B or 7092126, 1/4-20 Hex Center
Position: 17
1 GUARD, Rear Seat
Position: 17
2 WASHER, .34 x 1.0 x .09 Flat
Position: 17
1 WASHER, 3/8” Internal Tooth Lock
Position: 17
1 ROD, Timing (1/2-13 thread)
Position: 17
1 BOLT, 5/16-18 x 1-1/2” Hex Flange Lock, GR
Position: 17
1 COVER, Spindle, RH, Red, RZT 44/50”
Position: 17
1 DECAL, Sound
Position: 17
2 NUT, 1/4-20 Hex Center Lock, GR 5 or B
Position: 17
2 BRACKET, Axle Support
Position: 18
1 WASHER, .531 x 1.062 x .121 Flat, YZ
Position: 18
1 V-BELT, HA Sect. (wrapped) 58.00 effective length hydro drive
Position: 18
2 NUT, 1/4-20 Hex Nyloc
Position: 18
4 NUT, 5/16-18 Hex Flange Lock, GR
Position: 18
2 WASHER, 3/8” Flat SAE
Position: 18
2 SCREW, 1/4-15 x 1-1/4” Hex Washer Self-Tap
Position: 18
2 SPACER, .340 I.D. x .63 O.D. x .310 Thick
Position: 18
1 NUT, 3/8-24 Hex, GR B
Position: 18
2 NUT, 1/2-13 Hex Flange Lock, GR 5, YZ
Position: 18
2 PLUG, Hole (Polyethylene)
Position: 18
5 SCREW, 5/16-18 x 3/4” Hex Washer Self-Tap
Position: 18
13 PLUG, Hole (Polyethylene)
Position: 18
1 DECAL, Deck Symbols, International
Position: 18
2 SCREW, 1/4-20 x 5/8” Hex Head Cap, GR
Position: 18
8 WASHER, .34 x .69 x .08 Flat
Position: 19
1 SCREW 1/2-13 x 2-1/2” Hex Head Cap, GR 5 (Black Phosphate)
Position: 19
1 SHOULDER BOLT, 5/16 x 1/4-20
Position: 19
1 BRACKET, Switch
Position: 19
1 SCREW, 5/16-18 x 2-1/2” Hex Head Cap, GR
Position: 19
3 COTTER PIN, 1/2 Self Locking, YZ
Position: 19
2 WASHER, .28 x .63 x .06 Flat, GR 5 euro models
Position: 19
1 BRACKET, Lower Seat
Position: 19
3 CABLE TIE, 7”
Position: 19
1 COTTER PIN, 5/32 x 1”, YZ
Position: 19
1 NUT, 3/8-16 Hex Flange Lock
Position: 19
2 NUT, 1/4-20 Hex
Position: 19
1 DECAL, Panel Symbols, Euro RZT
Position: 19
1 BATTERY, 12 Volt, 230 CCA
Position: 19
4 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR 5, YZ
Position: 20
1 IDLER, 3.25” OD x .391 ID x 1.63 Backside
Position: 20
2 SCREW, 7/16-20 x 2-1/2” Hex Head Cap, GR 5 (Special Head) or 7900027 (7/16-20 x 4” Hex
Position: 20
1 SPACER, 9/16 OD x 12GA x .899
Position: 20
1 SWITCH- DPDT also shown in Electrical Group
Position: 20
1 NUT, 3/8-24 Hex Jam
Position: 20
1 SPACER, Motor
Position: 20
1 SWITCH, Single Pole, LG-1, NC
Position: 20
1 SCREW, 1/4-20 x 1” Hex Head Cap, GR
Position: 20
1 HEAT SHIELD, Fender, ERZT/EJAV
Position: 20
2 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR 5, YZ
Position: 20
1 MANIFOLD, 18 HP B&S Intek
Position: 20
1 MANIFOLD, B&S V-Twin Intek
Position: 20
1 GROOVE PIN, 1/4 x 1-1/4”
Position: 20
7 SCREW, 5/16-18 x 3/4” Hex Washer Self-Tap
Position: 20
2 LOCKWASHER, 1/4” Spring
Position: 20
5 SCREW, 5/16-18 x 3/4” Hex Washer Self-Tap
Position: 20
1 COVER, Battery Cable used on ERZT185440BVE &
Position: 20
1 WASHER, 3/8” Flat SAE
Position: 21
2 NUT, 7/16-20 Hex Center Lock Jam, GR 5 or B
Position: 21
2 SCREW, 1/4-20 x 1-1/4” Hex Head Cap, GR
Position: 21
2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap (Torx)
Position: 21
6 NUT, 1/4-20 Hex Nyloc YZ
Position: 21
1 ** MUFFLER, LC YZ 8.31 dimension from pipe
Position: 21
1 MUFFLER, RZT 7.56 dimension from pipe
Position: 21
1 ** MUFFLER, LC YZ 8.31 dimension from pipe
Position: 21
1 MUFFLER, RZT 7.56 dimension from pipe
Position: 21
1 CLEVIS PIN, 1/2 x 1-1/8” YZ
Position: 21
1 BOLT, 3/8-16 x 3/4” Hex Flange Lock, GR 5, YZ
Position: 21
1 WASHER, Large, 1/4 ID x 5/8 OD x .134/.109
Position: 21
1 WASHER, .33 x .88 x .09 Flat
Position: 21
2 WASHER, Large 1/4 ID x 5/8 OD x .134/.109
Position: 21
1 WASHER, 1/4” Internal Tooth Lock, YZ
Position: 21
1 NUT, 3/8-16 Hex Center Lock, GR 5 or B, YZ
Position: 22
1 SPRING, Extension, .562 OD x 4.250 long x .049 Wire B or
Position: 22
2 NUT 1/4-20 Hex Center Lock, GR 5 YZ
Position: 22
1 NUT, 10-24 Hex Nyloc
Position: 22
1 GASKET, Exhaust
Position: 22
2 GASKET, Exhaust, 20 HP Intek
Position: 22
1 WELDMENT, Link Lift
Position: 22
1 IDLER PULLEY BRACKET, 44/50”
Position: 22
1 BOLT, 1/4-20 x 7/8” Round Head Short Square Neck, GR
Position: 22
1 MAT, Foot Rest RZT
Position: 23
1 GUARD, Euro
Position: 23
8 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap
Position: 23
2 FLANGE BEARING, 9/16 I.D. P.M. powdered metal
Position: 23
6 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap
Position: 23
1 HOOK, Park Brake
Position: 23
3 WASHER, 5/16” Split Lock
Position: 23
5 WASHER, 5/16” Split Lock
Position: 23
2 WASHER, .531 x 1.062 x .121 Flat, YZ
Position: 23
1 BOLT, 3/8-16 x 2-3/4” Round Head Square Neck, GR
Position: 23
1 ROD, Deflector
Position: 23
2 BOLT, 1/4-20 x 7/8” Round Head Short Square Neck Carriage,
Position: 23
1 MAT, Floor Pan
Position: 24
2 PAD, Rubber Adhesive
Position: 24
1 PLATE, Fwd/Rev Adjust
Position: 24
1 SWITCH- DPDT also shown in Electrical Group
Position: 24
2 SET SCREW, 5/16-18 x 3/4” Socket Head, GR
Position: 24
4 SET SCREW, 5/16-18 x 3/4” Socket Head, GR
Position: 24
2 BRACKET, Rear Support, RH
Position: 24
2 BOLT, 3/8-16 x 2-1/4” Round Head Short Square Neck, GR
Position: 24
1 ROD, Pivot, Side Discharge, 50” Deck
Position: 24
2 SCREW, 3/8-16 x 5/8” Hex Washer Self-Tap
Position: 25
1 TRACK, Control Stick, LC YZ
Position: 25
1 SHOULDER BOLT, 3/8-16 2.013 long shoulder
Position: 25
1 ROD, Hanger (1/4-20 both ends) used on series
Position: 25
2 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap
Position: 25
5 SCREW, 1/4-20 x 3/4” Hex Head Flange, GR 5, YZ
Position: 25
8 NUT, 5/16-18 Hex Flange Lock, GR
Position: 25
1 PAD, Rubber Adhesive
Position: 25
1 CAP, Spring End
Position: 25
1 CONTROL BRACKET, LH
Position: 26
1 SHOULDER BOLT, 5/16 x 1/4-20 .800 long shoulder
Position: 26
1 BRACKET, Muffler 18HP Briggs
Position: 26
1 BRACKET, Muffler 20/22HP Briggs
Position: 26
2 BEARING, Powdered Metal
Position: 26
1 WASHER, .34 ID x .75 OD Flat
Position: 26
4 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5, YZ
Position: 27
1 SHOULDER BOLT, 5/16 x 1/4-20 1.360 long shoulder
Position: 27
2 SCREW, 1/4-20 x 3/4” Hex Head Cap, GR
Position: 27
1 SCREW, 1/4-20 x 1” Hex Head Cap, GR
Position: 27
4 BOLT, 5/16-18 x 7/8” Hex Flange Lock, YZ
Position: 27
1 CLAMP
Position: 27
4 NUT, 3/8-16 Hex Flange Lock
Position: 28
4 WASHER, .28 x .63 x .06 Flat, GR
Position: 28
2 WASHER, .28 x .63 x .06 Flat, GR
Position: 28
4 ADJUSTER, Chain
Position: 28
3 NUT, 3/8-16 Hex Nyloc
Position: 28
1 BRACKET, Rod Holder, RZT
Position: 29
1 WASHER, 1/4” Split Lock
Position: 29
4 SWIVEL, Shift Linkage, PM
Position: 29
6 WASHER, 3/8” Flat SAE
Position: 29
2 POP RIVET, 1/8 x 3/8”
Position: 30
2 WASHER, 1/4” I.D. Flat case hardened steel
Position: 30
1 NUT, 1/4-20 Hex, GR 5 or B
Position: 30
4 WASHER, .390 I. D. Flat
Position: 30
2 PULLEY, Flat Idler, 3-1/4” Dia.
Position: 30
7 WASHER, 3/8” Flat SAE
Position: 30
1 ROD END
Position: 31
1 ROD END
Position: 31
1 CLAMP, Muffler Briggs p/n
Position: 31
1 CLAMP, Muffler Briggs p/n
Position: 31
8 NUT, 5/16-18 Hex, GR 5 or B
Position: 31
3 WASHER, .468 x 1.625 x .25 Flat case hardened steel
Position: 31
1 SCREW, 3/8-16 x 1-1/2” Hex Head Cap, GR
Position: 32
1 ASSEMBLY, Fuel Tank, RZT includes items 33 thru
Position: 32
1 ASSEMBLY, Fuel Tank, RZT includes items 33 thru
Position: 32
4 HAIR PIN, 3/32 x 1-1/2”
Position: 32
2 WASHER, .406 x 1.50 x .120 Flat
Position: 32
4 WASHER, .406 x 1.50 x .120 Flat
Position: 32
2 NUT, 3/8-24 Hex, GR B, YZ
Position: 33
3 NUT, 3/8-24 Hex, GR B, YZ
Position: 33
1 FUEL TANK
Position: 33
1 WELDMENT, Lift Rear yellow zinc plated
Position: 33
1 PULLEY, 4” Flat Idler
Position: 33
2 PULLEY, Flat Idler 5.0 x .375 belt clutch
Position: 33
3 WASHER, 3/8” Flat
Position: 34
1 DIP TUBE
Position: 34
1 FOOT PEDAL, Rubber
Position: 34
1 NUT, 3/8-16 Hex Center Lock, GR 5 or B
Position: 34
1 NUT, 3/8-16 Hex Center lock
Position: 34
1 SPRING, Compression (Brake)
Position: 35
1 GROMMET
Position: 35
2 BEARING, 3/4” I.D. powdered metal
Position: 35
1 WASHER, .468 x 1.625 x .25 Flat
Position: 35
1 ROD, Link Fwd./Rev. (3/8-24 thread)
Position: 36
1 ELBOW, 90 Degree
Position: 36
1 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5, YZ
Position: 36
1 WELDMENT, Idler Swing Arm
Position: 36
1 CLEVIS PIN, 7/16 x 1”
Position: 37
1 BRACKET, LH Fender Support
Position: 37
1 CAP, Fuel, 3-1/2”
Position: 37
1 BRACKET, Foot Assist yellow zinc plated
Position: 37
1 IDLER SPACER, .75 x .390 x 1.800
Position: 37
1 COTTER PIN, 1/2 Self Locking, YZ
Position: 38
4 CLAMP, Fuel Line
Position: 38
1 SWIVEL, Timing Rod (1/2-13 external thread) yellow zinc plated
Position: 38
1 BOLT, 3/8-16 x 2-1/4” Round Head Short Square Neck, GR
Position: 38
1 SPACER, Idler (.75 x .390 x 1.800)
Position: 38
1 CLIP, Spring
Position: 39
2 HOSE, Fuel, 5”
Position: 39
2 HOSE, Fuel, .25 I.D. x 14” long
Position: 39
2 HOSE, Fuel, .25 I.D. x 5” long used on ERZT20441BVE2
Position: 39
1 WELDMENT, Bellcrank, RH yellow zinc plated
Position: 39
1 BELT, 44” Deck, 138.25" E.L. HB Section
Position: 39
1 BOLT, 3/8-16 x 2-1/4” Short Square Neck Carriage, GR
Position: 39
1 VALVE, Fuel Shut-Off
Position: 40
1 VALVE, Fuel
Position: 40
1 KEY, 3/16” Square x 1-1/2”
Position: 40
4 SHOULDER BOLT, 3/8-16 x 3/4” YZ replaces 7091526 (3/8-24 x 5/8”)
Position: 40
1 BELT, B Section, 150” Effective Length
Position: 40
1 BRACKET, Fender Support, RH
Position: 41
1 SEAL, Tank
Position: 41
2 BUSHING, Idler powdered metal
Position: 41
4 WHEEL, 4 x 1-7/8” Offset replaces 7026122 (1-1/2” offset)
Position: 41
4 SHOULDER BOLT, 3/8-16 x 3/4” YZ replaces 7091526 (3/8-24 x 5/8”)
Position: 41
1 SCREW, 5/16-18 x 1-3/4” Hex Head Cap, GR 5, YZ
Position: 42
2 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR
Position: 42
4 NUT, 3/8-16 Hex Center Lock replaces 7090289 (HCLN, 3/8-
Position: 42
4 WHEEL, 4 x 1-7/8” Offset replaces 7026122 (1-1/2” offset)
Position: 42
2 WASHER, .34 x .69 x .08 Flat
Position: 43
1 NUT, 5/16-18 Hex Center Lock, GR 5 or B, YZ
Position: 43
4 NUT, 3/8-16 Hex Center Lock replaces 7090289 (HCLN, 3/8-
Position: 43
1 NUT, 5/16-18 Hex, GR 5 or B
Position: 44
1 SUPPORT, Front Deck, RH
Position: 44
2 WASHER, 3/8” Flat
Position: 44
3 SPEED NUT, 1/4-20 U Type/070/.140 Black
Position: 45
1 TUBE, Manifold Extension
Position: 45
1 SUPPORT, Front Deck, LH
Position: 45
1 SPRING, Idler Primary
Position: 45
1 HEAT SHIELD, Muffler, ERZT, MY06
Position: 46
1 BRACKET, Fuel Pump Briggs part; used on item
Position: 46
2 SET SCREW, 5-16-18 X 1/2” Square Head w/locking patch
Position: 46
1 SPACER, .340 I.D. x .63 O.D. x .310 Thick
Position: 46
2 SCREW, #8-32 x 1/2” Cross Recess Pan Head
Position: 47
1 BOLT, 5/16-18 x 1-1/4” Square Neck Carriage, GR
Position: 47
1 WELDMENT, Front Lift yellow zinc plated
Position: 47
3 SCREW, 1/4-20 x 5/8” Hex Flange Lock w/locking patch
Position: 48
3 NUT, 5/16-18 Hex Flange Lock
Position: 48
3 BUSHING, .250 ID x .375 OD x .25 Long steel sleeve
Position: 49
3 RETAINER, 1/4” Bolt
Position: 50
1 PUSH NUT for .156 dia. Stud
Position: 51
3 SCREW, 1/4-20 x 5/8” Hex Flange Lock w/locking patch
Position: 51
1 BOLT, 5/16-18 x 1-1/4” Square Neck Carriage
Position: 52
3 BUSHING, .250 ID x .375 OD x .25 Long steel sleeve
Position: 52
2 NUT, 5/16-18 Hex Flange Lock, GR
Position: 53
1 PUSH NUT for .156 dia. Stud
Position: 54
1 SPACER, .65 x .88 x .10 (not shown) used on RZT22500BVE2
Position: 7016132
1 WIRE, Negative, Black 14” #8 AWG (not shown)
Position: 7042956
1 DECK GROUP, 50”
Position: 7050587
1 HARNESS, RZT (not shown)
Position: 7100306
1 WIRING HARNESS, Briggs 18.5 & 20 HP
Position: 7100306
1 CABLE, Battery Positive RZT, Red 20" #6 AWG (not shown)
Position: 7100307
1 WIRING HARNESS, Hour Meter, RZT (not shown)
Position: 7100324
1 CABLE, Battery Negative, RZT, Black 20" #8 AWG (not shown) used on ERZT185440BVE &
Position: 7100636
1 SUB-ASSEMBLY, Frame, (Red Paint) includes 22 Items shown below
Position: 7500012
1 ASSEMBLY, Fwd/Rev Rod incl. items 31, 33, 34, 35 &
Position: 7500059
1 ASSEMBLY, Fwd/Rev Rod incl. next 5 items
Position: 7500059
1 ASSEMBLY, Fwd/Rev Rod Includes items: 31, 33(2), 34(2),
Position: 7500059
1 ASSEMBLY, Fwd/Rev Rod Includes items: 34 thru 38.
Position: 7500059
1 ASSEMBLY, Fwd/Rev Rod Includes items: 7, 8, 31, 33(2),
Position: 7500059
1 ASSEMBLY, Fwd/Rev Rod includes the 7 items below
Position: 7500059
1 SUB-ASSEMBLY, 44” Deck, ERZT finish: Cardinal Red
Position: 7500188