Assistant réparation
Powered by ChatGPT
Liste des pièces détachées
Battery
Position : 1
Chassis
Position : 1
Control, Throttle/Choke 37 137040 Line, Fuel
Position : 1
Washer Asm Inner Spring W/ 15 173288 Link Front
Position : 1
Seat 15 134300 Spacer Split 28 x 96 Zinc
Position : 1
Decal, Warning Syms. CE 15 196357 Decal, Deflect Wrn Cutfinger Sym
Position : 1
Cap Value Tire
Position : 1
Mower Deck Assembly, 42” 68 180215 V-Belt
Position : 1
Kit, Main Housing 71 170417 Brake Spring
Position : 1
Drawbar
Position : 2
Axle Assembly Cast Iron
Position : 2
Shaft Asm. Lift 17 175689 Trunnion Blk Zinc
Position : 2
Bracket Pivot Seat 16 121250X Spring Cprsn 1 27 Blk Pnt
Position : 2
Decal, Chassis Hot Muffler 16 196841 Decal, Warning Eng. Syms.
Position : 2
Kit, Side Housing 74 170419 Seal, Oil
Position : 2
Spindle Assembly, L.H.
Position : 3
Decal, Hood 20 145005 Decal Battery Dngr/Psn Eng
Position : 3
Bracket Assembly,Sway Bar, Front 101 193107 Cover Mulching
Position : 3
Kit, Center Section 78 142969 Spring
Position : 3
Spindle Assembly, R.H.
Position : 4
Muffler 45 17000612 Screw Hxwsh Thdr 3/8-16 x 3/4
Position : 4
Decal, Steering Wheel -- 138311 Decal, Lift Handle
Position : 4
Tube Inner Front #35060
Position : 4
Bracket Sway Bar 38/42” Deck 102 71081010 Screw Pan Hd Phillips 10-24 x 5/8
Position : 4
Swashplate, Trunnion Machined 81 170423 Wedge, Friction
Position : 4
Bumper Hood/Dash
Position : 5
Clip Push In Hinged 17 123976X Nut Lock 1/4 Lge Flg Gr. 5 Zinc
Position : 5
Decal, Fender -- 166960 Decal, Drawbar Load Limit
Position : 5
Kit, Cylinder Block (10cc) 82 170424 Clip, Washer
Position : 5
Decal, Saddle Brake Parking -- 162598 Drawbar Load
Position : 6
Bar Sway Deck 104 10071000 Washer Lock #10
Position : 6
Sealant Tube 85 170426 Hose, Expansion Tank
Position : 6
Hexflange Screw 1/4-20 X 1.25 87 173160 Cap, Vent
Position : 7
Box Battery
Position : 8
Rod, Shift 73 169182 Strap, Torque, Rh
Position : 8
Bolt 5/16-18 unc x 3/4 w/Sems 46 19091416 Washer 9/32 x 7/8 x 16 Ga.
Position : 8
Decal, Cutfinger CE -- 184310X428 Pad, Footrest LH STLT
Position : 8
Bolt, Hex 3/8-24 x 1.25 Gr. 8 105 160793 Latch Asm. Mulch/Bagger
Position : 8
Stud, 5/16-24 Hex Double End 88 178334 Bolt, Self Tapping (BDR)
Position : 8
Decal, Fender -- 184311X428 Pad, Footrest RH STLT
Position : 9
Tire R Ts 20 x 8-8 Service
Position : 9
Shaft, Input 90 170430 Puck, Inner Wedge
Position : 9
Draglink
Position : 10
Pan Asm. Seat 41 140675 Strap Asm. Fender
Position : 10
Decal, Brake/Clutch -- 404870 Manual, Operator's (Euro)
Position : 10
Washer, Hardened 111 179292 Bracket Gauge Wheel Lh
Position : 10
Retaining Ring 93 170431 Spring Clip, Housing
Position : 10
Panel, Dash, L.H.
Position : 11
Link Asm Lift L.H. NOTE: All component dimensions given in U.S. inches
Position : 11
Knob Seat Adj Wingnut
Position : 11
Decal, Panel Side -- 404871 Manual, Operator's (Scan)
Position : 11
Blade, 42" Mulching Std 112 179293 Bracket Gauge Wheel Rh
Position : 11
Spacer 107 170432 Deflector
Position : 11
Link Asm Lift R.H. 1 inch = 25.4 mm
Position : 12
Bracket Pnt Mounting Switch
Position : 12
Decal, V-Belt Drive Schematic -- 404872 Manual, Operator's (EBloc)
Position : 12
Retaining Ring 108 170433 Washer, Motor Shaft
Position : 12
Spacer Bearing Axle Front
Position : 13
Gasket 81 73510400 Nut Keps Hex 1/4-20
Position : 13
Decal, Chassis -- 404873 Manual, Operator's (Baltic)
Position : 13
Shaft Assembly, Mandrel, Vented 116 4898H Bolt Shoulder
Position : 13
Seal, Lip .67 X 1.58 X .276 .71ID X 1.15OD X .03 Thick
Position : 13
Tube Drain Oil Easy 105 17120616 Screw 3/8-16 x
Position : 14
Decal, V-Belt Schematic -- 404874 Manual, Parts
Position : 14
Housing, Mandrel, Vented 117 188606 Wheel Gauge
Position : 14
Bearing, Ball 6203 (BDR) 109 170434 Plug, Straight Thread 9/16-18
Position : 14
Nut, Hex Flange Lock
Position : 15
Switch, Interlock
Position : 16
Stripper, Vented Mower Deck 119 19121414 Washer 3/8 x 7/8 x 4 Ga.
Position : 16
Hex Flange Head Screw 1/4-20 X 1.25 111 170435 O-ring .7 X .301 ID
Position : 16
Shaft, Steering
Position : 17
Seal, Lip 18 X 32 X 7 113 170437 Bracket, Support Expansion Tank
Position : 17
Bumper Hood
Position : 18
Arm, Control 119 191031 Kit, Fan - Washer - Nut
Position : 18
Bolt, Shoulder 130 STD523710 Bolt, Fin Hex 3/8-16 unc x 1 Gr.
Position : 19
Bearing, Thrust (10cc) Fan, 7 In
Position : 19
Baffle, Vortex 131 STD533710 Bolt, Rdhd Sqnk 3/8-16 unc x1
Position : 20
Harness Asm Light W/4152j
Position : 21
Knob 81 165596 Shaft Asm Cross
Position : 21
Rod, Brake 82 165711 Spring, Torsion
Position : 22
Shield Brn/Dbr Guard 116 184362 Nut Hex Flange Toplock M8-1.25
Position : 23
Bracket, Deflector 143 157109 Bracket Arm Idler 42”
Position : 23
Check Plug Assembly Hex Lock Nut 1/2-20 (Nylon Insert)
Position : 23
Shaft Motor Washer, Or Slotted, .53 X 1.63 X .06
Position : 24
Cable Battery
Position : 25
Fuse
Position : 26
Gear, Pinion, 13t 120 188312 Pulley
Position : 27
Grille/Lens Asm.
Position : 28
Rod, Parking Brake 96 STD624003 Spring, Retainer 1”
Position : 28
10t / 48t Gear 123 178800 Belt Keeper
Position : 28
Switch Seat DP w/ROS
Position : 29
Cap, Parking Brake 112 19091210 Washer 9/32 x 3/4 x 10 Ga.
Position : 29
Arrestor, Spark 117 188654 Tube Exhaust
Position : 29
Rod, Hinge 149 165898 Retainer Spring Yellow Zinc
Position : 29
Gear, 10t Jackshaft 124 170444 Kit, Center Section Filter Bypass
Position : 29
Switch Ign
Position : 30
Bracket, Transmission 116 72140608 Bolt Rdhd Sq Neck 3/8-16 x
Position : 30
Screw Thdrol Washer Head 150 19091210 Washer 9/32 x 3/4 x 10 Ga.
Position : 30
60t Bullgear Center Section Machining
Position : 30
Bracket, Fender Support
Position : 31
Tank, Fuel
Position : 31
Washer, Spacer 152 181555 Cable Clutch 42 In
Position : 31
Sleeve Bearing .75 X 1.75 X .625 Base Filter W/ Poppet
Position : 31
Rod, Tie
Position : 32
Cap Assembly, Fuel Sears, Vented
Position : 32
Pulley, Mandrel 158 17720408 Screw Hex Thd Cut 1/4-20 x 1/2
Position : 32
Sleeve Bearing (Outboard).75 X 1.575 X .625 Check Plug Assembly, .027 Washer
Position : 32
Key Ign
Position : 33
Nut, Toplock, Flanged 159 72140614 Bolt Rdhd Sqn 3/8-16 unc x 3/4
Position : 33
Washer Check Plug Assembly, Washer
Position : 33
Shaft, Foot Pedal 150 175456 Spacer Retainer
Position : 34
Lip Seal, Axle Shaft Spring, Bypass, Actuator, Bypass
Position : 34
Shaft, Axle (Keyed, R.h.) Deflector, Bottom, Filter
Position : 35
Bushing, Steering
Position : 36
Pulley, Idler, Flat 185 188234 Head Asm Cable Clutch
Position : 36
Shaft, Axle (Keyed, L.h. ) Bushing, .707 X .788 X .591
Position : 36
Screw
Position : 37
Gear, Splined Diff.(210-1000 & 310-0750) 125 170445 Kit, Filter
Position : 37
Pivot Bracket Assembly, Rear
Position : 38
Pulley, Composite 159 183900 Hub Tapered Flange Shift
Position : 38
Gear, Miter Diff. (210-1000 & 310-0750) Bottom, Filter
Position : 38
Bracket Pivot Laser Lt
Position : 39
Differential Shaft (310-0750) Spring, Bypass, Actuator, Bypass
Position : 39
Harness Ign
Position : 40
Retaining Ring Deflector, Base, Filter W/ Poppet
Position : 40
Keeper, Belt, Idler 1/4-20 x 3/4 Gr.
Position : 41
Adaptor, Steering Wheel
Position : 41
Pin, Jackshaft 126 191028 Kit, Fan/pulley
Position : 41
Cover Terminal Red
Position : 42
Magnet, Ring Hex Jam 1/20-20 (Nylon Inser)
Position : 42
Solenoid
Position : 43
Spring, Bypass Washer, OD Slotted, .53 X 1.63 X .06
Position : 43
Extension Shaft Steering
Position : 44
Guard, Mandrel, L.H. Housing, Shaft and Shaft
Position : 44
Bolt 3/8-24 X 2-1/2 Fan, 7 In
Position : 44
Filter Pulley
Position : 45
Screw, Thd. Roll 1/4-20 x 5/8 Included)
Position : 46
Base, Filter 127 170447 Kit, Seal
Position : 46
Pulley, Idler, V-Belt 162 73680400 Nut Crownlock 1/4-20 unc
Position : 47
Actuator, Bypass Lip Seal .67 X 1.58 X .276
Position : 47
Adapter Ammeter
Position : 48
Bellcrank Clutch Grnd Drustl 163 74780416 Bolt Hex Fin 1/4-20 x
Position : 48
Washer, Hardened -- 181281 Replacement Mower, Complete
Position : 48
Rod, Bypass Actuator Lip Seal 18 X 32 X
Position : 48
Arm, Bypass Lip Seal .706 X 1.584 X .25
Position : 49
Retaining Ring .25 External Lip Seal .741 X .250 X .250 Tc
Position : 50
Seal, Lip .741 X .25 X .25 Oil Seal .625 X 1.0 X .25
Position : 51
Protection Wire Loop
Position : 52
Bolt, Shoulder 5/16-18 unc (Std. Deck-Order separately
Position : 52
Washer, Flat 0.050” (210-1000) O-ring .07 X .301 ID
Position : 52
Link, Clutch 197 169613 Nyliner Snap-In
Position : 53
Arm Assembly, Pad, Brake gauge wheel components key nos.
Position : 53
Retaining Ring 128 173165 Kit, Expansion Tank
Position : 53
Washer, Hardened 116 - 119).
Position : 54
Bearing, Center Block Tank, Expansion
Position : 54
Arm, Idler
Position : 55
Spring, Helical Compression Cap, Vent
Position : 55
Spacer, Retainer NOTE: All component dimensions given in U.S. inches
Position : 56
Washer, Block Thrust Bolt, Self Tapping 10-32 X 1/2
Position : 56
V-Belt, Drive 200 72140508 Bolt RdHd Sqnk 5/16-18 unc x
Position : 57
Duct Air
Position : 58
Kit, Brake Yoke Silicon Sponge 1/2 X 1/2 X 3/16
Position : 58
Keeper, Belt, Center 202 72110614 Bolt Carr. Sh
Position : 59
Guard, TUV Idler 1 inch = 25.4 mm
Position : 59
Rotor, Brake 129 191032 Cap, Expansion Tank Shipping
Position : 59
Brake Puck 130 186352 Kit, Brake Arm And Spring
Position : 60
Brake Puck Plate Arm, Brake
Position : 61
Pin, Brake Actuating Spring, Brake Arm Bias
Position : 62
Pulley, Engine 263 17000612 Screw 3/8-16 x 3/4
Position : 63
Hfhcs 1/4-20 X 2 W/patch, Special Flg Instruction Sheet
Position : 63
Dash Lower STLT
Position : 64
Bolt Hex 268 182402 Guard Muffler
Position : 64
Bolt, Nylok 900 166768 Transaxle
Position : 64
Spacer Brace Axle
Position : 65
Spacer, Brake Torsion Spring
Position : 65
Keeper, Belt Engine Hydro
Position : 66
Knob Custom Oval
Position : 67
Bolt, Square Head - Brake NOTE: All component dimensions given in U.S. inches 1 inch
Position : 67
Axle, Brace
Position : 68
Screw Hex Wsh Hi-Lo NOTE: All component dimensions given in U.S. inches
Position : 69
Nut, Castle 5/16-24 = 25.4 mm
Position : 69
Pin, Cotter 3/32x3/4
Position : 70
Steering Asm.
Position : 71
Bracket Susp. Chassis Front
Position : 82
Washer Flat .781 x 1-1/2 x .14
Position : 87
Bolt Shoulder 7/16-20 unc
Position : 88
Cover Terminal
Position : 90
Clip Steering
Position : 91
Harness Pigtail
Position : 92
Screw Plastic 10-14 x 2.0
Position : 93
Module Reverse ROS
Position : 94
Washer Hardened
Position : 95
Plate Reinforcement STLT
Position : 142
Bracket Swaybar Chassis
Position : 143
Bracket Pnt Footrest STLT
Position : 144
Rod Pivot Chassis/Hood
Position : 145
Bolt Shoulder 5/16-18 TT
Position : 206
Bezel Grille Laser LH
Position : 263
Bezel Grille Laser RH
Position : 264
Screw 10 x 3/4 Single Lead-Hex
Position : 278
Rev. 1 04.24.06 TR
Position : 404874