Assistant réparation
Powered by ChatGPT
Liste des pièces détachées
1 BATTERY BOX, W/ DRAIN HOLE
Position : 1
1 TANK, 5 GAL, W DROP TUBE/VENT (S/N: 2014985585 & Above)
Position : 1
1 TANK, FUEL, TOP DRAW (S/N: 2014433879 - 2014985584)
Position : 1
1 GRIP, FOAM, 1/4" X
Position : 1
2 KEY, 3/16 SQ. X 2-1/2
Position : 1
1 DECAL, FERRIS TEXT & LOGO
Position : 1
1 DECAL, CONTROL PANEL, HC
Position : 1
1 DECAL, CONTROL PANEL HC/CE
Position : 1
1 CNSTR, CARB, 6 GAL
Position : 1
2 TIE,SELF-LOCKING, 6"
Position : 1
4 WASHER, 1" SAE
Position : 1
1 BELT
Position : 1
4 WASHER-1.00 HYDRO CUT
Position : 1
1 BELT,#7-8390,
Position : 1
1 SWITCH, PLUNGER NC (OPERATOR PRESENCE)
Position : 1
1 STRAP, RUBBER
Position : 2
1 FUEL CAP, 3-1/2", MANAGED VENT OUT, 12"
Position : 2
9 NUT, 5/16-18 HEX NYLOCK FLANGE
Position : 2
2 DRIVE HUB (Includes Ref No. 8)
Position : 2
1 DECAL, HydroCut
Position : 2
1 DECAL, HEIGHT OF CUT (32" model)
Position : 2
1 DECAL-CUT HEIGHT ADJUST HYDRO CUT
Position : 2
1 SWITCH, BLADE ENGAGEMENT (PTO SWITCH)
Position : 2
2 SCREW, #10-24 X 1 RS, CZ
Position : 3
1 SWITCH, Plunger, NO/NO
Position : 3
9 WASHER, 5/16" SAE
Position : 3
2 WHEEL & TIRE ASSEMBLY, 16 x 6.5 x 8, Complete (Includes Ref No. 4 & 5)
Position : 3
1 DECAL, HYDROCUT
Position : 3
1 DECAL, HEIGHT OF CUT (36" model)
Position : 3
2 CLAMP, 3" ID, CUSHIONED, STAINLESS
Position : 3
1 GUARD, MOWER HOUSING
Position : 3
8 SHOULDER BOLT, 1/2 x 3/8
Position : 3
2 SPINDLE PULLEY
Position : 3
1 GUARD, MOWER DECK
Position : 3
8 BOLT, 3/8-16 X 3/8", 1/2" SHOULDER
Position : 3
1 SPACER, 1.00 X 1.50 X 1.19
Position : 3
1 SWITCH, IGNITION, 6 POST (IGNITION SWITCH)
Position : 3
2 NUT, #10-24 HEX NYLON LOCK
Position : 4
6 NUT, #10-24 HEX (S/N: 2013136020 & Below use Qty.8)
Position : 4
2 DECAL, FERRIS TEXT & LOGO
Position : 4
1 DECAL, DECK HEIGHT ADJUST
Position : 4
1 DECAL, HEIGHT OF CUT
Position : 4
1 FITTING, 3/16" TEE, BARB TYPE, HDPE
Position : 4
1 HEIGHT ADJUST ROD
Position : 4
8 SPACER, 1.02 X 1.56 X .50
Position : 4
1 ROD CUTTER DECK HEIGHT CONTROL
Position : 4
2 NUT, 1/2-13 HEX NYLOCK FLANGE
Position : 4
1 KEY, IGNITION, MOLDED SET (SV)
Position : 4
1 WASHER, 5/16 INT. TOOTH LOCK
Position : 5
1 SWITCH, Plunger, NC (S/N: 2013136020 & Below use Qty.3)
Position : 5
1 DECAL, 32" DECK, SILVER
Position : 5
1 DECAL, BELT R&R (36" model)
Position : 5
2 DECAL-DANGER ROTATING BLADE SYMBOLS
Position : 5
4 BODY CLIP, 5/16-18
Position : 5
1 LINKAGE ADJUSTER
Position : 5
4 BODY CLIP, 5/16-18 X 1/2" DEEP
Position : 5
1 LINKAGE, ADJUSTER
Position : 5
2 SPACER, .52 X 1.00 X .44
Position : 5
1 COVER, PLASTIC SNAP ON (SV)
Position : 5
4 WASHER, 5/16 SAE
Position : 6
1 CLUTCH, OGURA, INTEGRATED KEY (S/N: 2016545303 & Above)
Position : 6
1 DECAL, HOT SURFACE WARNING
Position : 6
2 DECAL, CE DANGER
Position : 6
2 BODY CLIP, 1/4-20 X 1/2 DEEP
Position : 6
1 FILTER, FUEL
Position : 6
4 WASHER, 1/4" Lock
Position : 6
1 NUT, 3/8-16 Hex Side Lock
Position : 6
4 WASHER, 1/4" LOCK
Position : 6
1 NUT, 3/8-16 HEX NYLON LOCK
Position : 6
1 PULLEY, FLAT IDLER, 5.0X.75
Position : 6
1 NUT, PLASTIC (SV)
Position : 6
2 WASHER, 1/4 SAE
Position : 7
4 BEARING, BRONZE FLANGE, 3/4
Position : 7
2 C-CLIP
Position : 7
1 DECAL, FIRE HARARD, 3.25W X 3.0H
Position : 7
1 NUT, 1/4-20 Hex Serrated Flange
Position : 7
1 WIRE HARNESS, HANDLE BAR
Position : 7
2 GRIP, FOAM, .940 X 5 X .187
Position : 8
2 PAD, RUBBER MOUNT
Position : 8
1 SPACER, .45 X 1.88 X .38
Position : 8
1 ROD, PARKING BRAKE LINKAGE
Position : 8
1 HYDRO RETURN SPRING (SV)
Position : 8
8 LUG NUT, 1/2-20
Position : 8
2 DECAL, DANGER DO NOT OPERATE W/O DEFLECT
Position : 8
8 NUT, 3/8-16 Hex Top Lock
Position : 8
10 NUT, 5/16-18 Hex Nylock Flange
Position : 8
8 NUT, 3/8-16, HEX TOP LOCK
Position : 8
2 NUT, 3/4-16 HEX
Position : 8
4 NUT, 1/4-20 HEX SERRATED FLANGE
Position : 8
1 SWITCH, BLADE ENGAGEMENT
Position : 9
3 COLLAR, 5/16" SET
Position : 9
1 DECAL, HYDRO RELEASE
Position : 9
8 NUT, 3/8-16 Hex Serrated Flange
Position : 9
1 COLLAR, 3/8" Set
Position : 9
2 SPINDLE ASSEMBLY, Complete (Includes Ref No. 10 - 18)
Position : 9
16 NUT, 3/8-16 HEX NYLOCK FLANGE
Position : 9
1 COLLAR, 3/8" SET
Position : 9
1 SWITCH, PLUNGER, N.O./N.C. (PARKING BRAKE)
Position : 9
1 RING, SWITCH RETAINER
Position : 10
4 CLAMP, HOSE, EXTERNAL, 1/2 - RED
Position : 10
5 NUT, 5/16-18 HEX NYLOCK FLANGE
Position : 10
1 TRANSAXLE, HYDROSTATIC
Position : 10
7 WASHER, 3/8" SAE
Position : 10
2 GREASE FITTING
Position : 10
16 WASHER, 3/8" SAE
Position : 10
1 SPACER, 1.00 X 1.57 X 2.19
Position : 10
1 BATTERY CABLE, POSITIVE, 22" (BATTERY TO SOLENOID)
Position : 10
1 NUT, 3/8-24 HEX
Position : 11
1 WASHER, 3/4 SAE
Position : 11
4 WASHER, 5/16" SAE
Position : 11
1 BELT,# 46-4631
Position : 11
12 WASHER, 3/8" SAE
Position : 11
1 SPRING, Compression
Position : 11
2 NUT, 3/4-16 Hex
Position : 11
4 KNOB, PLASTIC, 5/16-18 X
Position : 11
1 SPRING, REVERSE RETURN
Position : 11
1 BELT, SPROCKET DRIVE
Position : 11
1 WIRE HARNESS, ENGINE DECK, KAWASAKI (S/N: 2014433878 & Below)
Position : 11
1 WIRE HARNESS, ENGINE DECK, KAWASAKI (16HP Models)
Position : 11
1 BUSHING-FUEL TANK RED RUBBER (SV)
Position : 12
1 C-CLIP, 3/4 SHAFT
Position : 12
1 SPRING, EXTENSION
Position : 12
4 KNOB
Position : 12
2 WASHER, 3/4 BELLEVILLE
Position : 12
2 KEY, 1/4" SQ. X 3/4
Position : 12
2 NUT, 1/4-20 HEX NYLOCK FLANGE
Position : 13
1 PICKUP TUBE ASM, FUEL TANK, 8.0"
Position : 13
2 NUT, 3/8-16 HEX TOP LOCK
Position : 13
2 NUT, 3/8-16 HEX SIDE LOCK
Position : 13
4 TRASH SHIELD
Position : 13
1 CASTER MOUNT FRAME, COMPLETE (Includes Ref No. 14 & 32)
Position : 13
2 SPROCKET, GOODYEAR EAGLE PD
Position : 13
1 BATTERY CABLE, NEGATIVE, 22" (S/N: 2014433878 & Below)
Position : 13
1 BATTERY CABLE, NEGATIVE, 35" (16HP Models)
Position : 13
1 SWITCH, IGNITION, 6 POST
Position : 14
1 WASHER, 1/2 SAE
Position : 14
2 CAP, Plastic
Position : 14
4 NUT, 5/16-18 HEX SERRATED FLANGE (LARGE)
Position : 14
4 BEARING
Position : 14
10 NUT, 5/16-18 HEX NYLOCK FLANGE
Position : 14
2 WASHER, 5/16 SAE
Position : 15
2 NUT, 5/16-18 HEX SERRATED FLANGE (LARGE)
Position : 15
1 SPRING, COMPRESSION (S/N: 2013136021 & Above)
Position : 15
1 WASHER, 3/8" FENDER
Position : 15
2 RELIEF VALVE
Position : 15
4 NUT, 1/4-20 HEX NYLON LOCK
Position : 15
2 ASSM, SPINDLE, BLADE SADDLE (Includes Ref. 16 - 22)
Position : 15
2 NUT, HEX JAM 5/16-24 (SV)
Position : 15
2 NUT, 5/16-18 HEX NYLOCK FLANGE
Position : 16
1 GROMMET, 7/8
Position : 16
1 HANDLE, RUBBER HYDROCUT - LH (S/N: 2014433878 & Below)
Position : 16
1 SPACER, .41 X .75 X 2.06
Position : 16
1 CASTER MOUNT FRAME, Complete (Includes Ref No. 17 & 28)
Position : 16
2 SPACER, .39 x .75 x .38
Position : 16
2 SPINDLE HOUSING
Position : 16
2 SPACER, .39 X .75 X .38
Position : 16
2 WASHER, LIGHT LOCK, 5/16 (SV)
Position : 16
4 NUT, 5/16-18 HEX NYLOCK FLANGE
Position : 17
2 BODY CLIP, 1/4-20 X 1/2 DEEP (Not Shown)
Position : 17
1 HANDLE, RUBBER HYDROCUT - RH (S/N: 2014433878 & Below - Not Shown)
Position : 17
2 GREASE FITTING
Position : 17
2 COLLAR, Double Split, 1"
Position : 17
2 SPACER, 1.00 x 1.25 x 1.75
Position : 17
1 FLAP, RUBBER
Position : 17
2 COLLAR, 1" DOUBLE SPLIT
Position : 17
1 SOLENOID-4 POLE 12 VOLT DC (TROMBETTA)
Position : 17
1 CABLE, CHOKE CONTROL, 43.5"
Position : 18
1 PULLEY-IDLER, 5.00OD, .505ID, 1.25W, STL (32" Models)
Position : 18
1 NUT, 1/4-20 HEX NYLOCK FLANGE (S/N: 2013136021 & Above)
Position : 18
3 NUT, 3/8-16 Hex Serrated Flange
Position : 18
2 SPINDLE SHAFT
Position : 18
6 NUT, 3/8-16 HEX NYLOCK FLANGE
Position : 18
1 BATTERY CABLE, POSITIVE,
Position : 18
1 CABLE, THROTTLE CONTROL, 40"
Position : 19
1 SPRING, EXTENSION (32" Models)
Position : 19
4 NUT, 1/4-20 HEX SERR. FLANGE
Position : 19
1 PULLEY, IDLER ASSEMBLY
Position : 19
2 AXLE, Caster Wheel
Position : 19
1 CUT HEIGHT INDICATOR
Position : 19
8 BOLT, Flange Head, 5/16-18 x 1-1/4
Position : 19
1 POINTER, CUT HEIGHT
Position : 19
1 WASHER, 3/8" SAE
Position : 20
1 NUT, 3/8-16 Hex
Position : 20
2 NUT, 3/8-16 HEX
Position : 20
4 WASHER, 3/8 SAE
Position : 21
1 SPACER, .52 X 1.00 X .44, CZ
Position : 21
2 WASHER, 5/8" USS
Position : 21
4 NUT, 3/8-16 HEX NYLOCK FLANGE
Position : 22
1 HOSE, OIL DRAIN
Position : 22
1 PULLEY, DRIVE, 4.50 OD X 1.000 ID (SV)
Position : 22
2 SPINDLE SHAFT w/ SADDLE
Position : 22
4 BOLT,HEX FLG,SER GD5 3/8-16X1-1/4PACH CZ
Position : 23
1 FAN / PULLEY KIT, TRANSAXLE (S/N:2015250408 & Above - Not Shown)
Position : 23
1 DECK SHELL W/ DECALS, 32" - HYDROCUT (Includes safety decals)
Position : 23
2 AXLE, CASTER WHEEL
Position : 23
8 BOLT, 5/16-18 X 1 1/4" FLANGE
Position : 23
2 BOLT, 3/8-16 X 1.0", 1/2" SHOULDER
Position : 24
2 BEARING, Roller (1 per tire)
Position : 24
1 GREASE FITTING
Position : 24
4 RETAINER, Bearing (2 per tire)
Position : 25
1 WASHER, 3/8" NYLON HYDRO CUT
Position : 25
2 NUT, 1/2-13 Hex Nylon Lock
Position : 26
4 NUT, 3/8-18 Hex NylockFlange
Position : 26
2 NUT, 5/16-24 HEX NYLON LOCK
Position : 26
4 WASHER, 3/8" GD.9 FLAT
Position : 26
1 PULLEY, DRIVE, 4.50 OD X 1.000 ID
Position : 27
4 WASHER, 5/16" GR.9 FLAT
Position : 27
4 BUSHING, Flange
Position : 28
3 NUT, 3/8-16 HEX NYLOCK FLANGE
Position : 28
2 WASHER, 5/16 USS
Position : 29
8 CLEVIS, 5/16-24, STEEL, CLEAR ZINC
Position : 29
4 NUT, 3/8-16 Hex Nylon Flange
Position : 29
1 NUT, 1/2-13 HEX NYLOCK FLANGE
Position : 30
8 NUT, 5/16-24 HEX
Position : 30
2 COLLAR, 3/4" Split
Position : 30
1 CHUTE, RUBBER (S/N: 2013244263 & Above)
Position : 30
2 NUT, 1/2-13 HEX NYLON LOCK
Position : 30
1 SPRING, COMPRESSION 2" MEDIUM
Position : 30
2 ROD, THUMB CONTROL LINKAGE
Position : 31
1 DECK SHELL W/ DECALS, 36", HYDROCUT
Position : 31
1 NUT, 3/8-16 HEX SERRATED FLANGE
Position : 32
1 CASTER MOUNT FRAME W/ LOCKS, Complete (Includes Ref No. 17 & 28)
Position : 32
4 BUSHING, FLANGE, 3/4 X
Position : 32
2 WASHER, 3/8 SAE
Position : 33
1 NUT, 5/16-18 HEX SERRATED FLANGE (LARGE)
Position : 33
1 ROD, CHUTE PIVOT (S/N: 2013244263 & Above)
Position : 33
1 PULLEY, SPINDLE
Position : 33
2 NUT, 3/8-16 HEX NYLOCK FLANGE
Position : 34
1 BOLT, 5/16-18 X 1 1/2" FLANGE
Position : 34
2 CAP,VINYL, 1.375 X
Position : 34
1 WASHER, .390 X 1.50 X .109, YZ (S/N: 2013244263 & Above)
Position : 34
2 COLLAR, 3/4" SPLIT
Position : 34
4 WASHER, 1/4 SAE
Position : 35
4 WASHER, 1/4" SAE
Position : 35
2 BELLEVILLE WASHER 1.1875 X .442 X .089 (S/N: 2015745414 & Above)
Position : 36
1 LINK, STUD
Position : 36
1 SPRING-EXT, .665 OD X 4.375 LG X .098 WR (36" Models)
Position : 37
1 FLAP, RUBBER, 32RD (Rear Discharge Models)
Position : 37
1 CLAMP, WIRE, .312DIA . (1) .281 HOLE BLK
Position : 37
1 PULLEY-IDLER-V, 4.85OB, .506 ID, ,94W, STL (36" Models)
Position : 38
1 SPRING, EXT, 3.875 X .70 LOOP
Position : 38
1 SPRING, TORSION
Position : 38
1 LINK, PARKING BRAKE LOWER
Position : 39
1 DEFLECTOR, BLACK
Position : 39
2 COLLAR, 1/4" SET
Position : 40
1 CAP, VINYL
Position : 40
1 LEVER, DUMP VALVE
Position : 41
2 NUT, 1/4-20 HEX NYLON LOCK
Position : 41
4 NUT, 1/4-20 HEX NYLOCK FLANGE
Position : 42
1 NUT, 3/8-16 HEX NYLOCK FLANGE
Position : 43
8 WASHER, 1/4" SAE
Position : 44
4 NUT, 3/8"-16 HEX NYLOCK FLANGE
Position : 45
4 WASHER, 3/8" SAE
Position : 46
1 ROD, OPC SWITCH, PACER (S/N: 2013136021 & Above)
Position : 48
2 SPACER, SHOULDER (S/N: 2013136021 & Above)
Position : 49
2 ADJUSTER, LINKAGE (S/N: 2013136021 & Above)
Position : 50
2 NUT, 3/8-16 HEX (S/N: 2013136021 & Above)
Position : 51
2 GRIP, VINYL, 1/2 X 4 (S/N: 2013136021 & Above)
Position : 52
1 MOUNT, MOTION CONT, LH (S/N: 2013136020 & Below)
Position : 55
1 MOUNT, MOTION CONT, RH (S/N: 2013136020 & Below - Not Shown)
Position : 56
4 SPACER, SLIDE (S/N: 2013136020 & Below)
Position : 57
1 HANDLE, RUBBER, HYDROCUT - LH (S/N: 2014433879 & Above)
Position : 59
1 HANDLE, RUBBER, HYDROCUT - RH (S/N: 2014433879 & Above - Not Shown)
Position : 61
1 HYDRO RETURN SPRING
Position : 101
Aubière Cedex
Position : 63178
Hydrocut Series w/ 32" Mower Deck - Export (HC32KAV15ECE)
Position : 5900543
Hydrocut Series w/ 32" Rear Discharge Mower Deck - Export (HC32RDKAV15ECE)
Position : 5900544
Hydrocut Series w/ 36" Mower Deck (HC36KAV15E)
Position : 5900545
Hydrocut Series w/ 32" Mower Deck (HC32KAV15E)
Position : 5900546
16HP Kawasaki Electric Start w/ 32" Mower Deck (HC32KAV16E)
Position : 5900962
16HP Kawasaki Electric Start w/ 36" Mower Deck (HC36KAV16E)
Position : 5900963
16HP Kawasaki Electric Start w/ 32" Mower Deck - Export (HC32KAV16ECE)
Position : 5900989
16HP Kawasaki Electric Start w/ 32" Rear Discharge Mower Deck - Export (HC32RDK
Position : 5900990