Assistant réparation
Powered by ChatGPT
Liste des pièces détachées
4 SCREW, 5/16-18 X 1 PHILLIPS HD, BZ (Was 5025303)
Position : 1
8 MNT, VBRTN, RBBR
Position : 1
2 CLAMP, HOSE EXTERNAL, 1/2 - RED
Position : 1
10 WASHER, 5/16 LOCK YZ
Position : 1
1 FILTER-AIR CLEANER CA (794935) (SV)
Position : 1
1 5" AIR CLEANER ASSEMBLY (809670)
Position : 1
1 PULLEY, IDLER-V, 5.83OB, .381ID, .94W
Position : 1
4 10MM BALL STUD, 5/16-18 X 3/4 THDS
Position : 1
2 BALL JOINT, 5/16-24 LH FEMALE W/STUD, BR
Position : 1
1 3400 TRANS, LH, ZS-KHEF-8T7C-11RX
Position : 1
2 WASHER, 1/2 SAE
Position : 1
1 DECAL, FERRIS, FRONT, 8.78 X 5.81
Position : 1
1 DECAL, MAIN SAFETY
Position : 1
1 DECAL, MAIN SAFETY, ANSI CE
Position : 1
1 CNSTR, CARB, 6 GAL
Position : 1
1 FITTING, 3/16" TEE, BARB TYPE, HDPE
Position : 1
2 WHEEL- 2.00 WIDE 3.88 DIA 0.531ID POLY
Position : 1
1 DECK SHELL W/ DECALS, 52, IS700Z (SV) (5410273B)(S/N: 2016528079 &
Position : 1
1 DECK SHELL W/DECALS, 700-52, DOM (SV) (5413038B)(S/N: 2016528080 &
Position : 1
1 DECK SHELL W/ DECALS, 61, IS700Z (5410152B)(S/N: 2016528079 & Below)
Position : 1
1 DECK SHELL W/ DECALS, 700-61, DOM (5413074B)(S/N: 2016528080 &
Position : 1
1 DECK SHELL W/ DECALS, 52RDCE, IS700Z (5410697B)(S/N: 2016528079 &
Position : 1
1 DECK SHELL W/ DECALS, 52RD-CE, 700 (5413041B)(S/N: 2016528080 &
Position : 1
1 ASSM, SPINDLE, LOW PROFILE (Nut and Washer Sold Seperately)
Position : 1
1 WIRE HARNESS, C TURF,WARNER, IS600/IS700 (Models equipped with Briggs
Position : 1
1 RING, SWITCH RETAINER
Position : 2
1 SPACER, 1.13 X 1.75 X 1.25
Position : 2
1 FILTER-OIL (695396) (SV)
Position : 2
1 AIR FILTER - INNER
Position : 2
1 SPACER, .390 X 1.00 X .188, CZ
Position : 2
14 NUT, 5/16-18 HEX NYLOCK FLANGE
Position : 2
4 WAVE WASHER, 1/2"ID X 087"OD X .01 THK.
Position : 2
1 3400 TRANS, RH, ZS-GHEF-8T7B-11 RX
Position : 2
4 ADAPTER, CASTER AXLE, CZ (SV)(Qty: 2 per tire)
Position : 2
1 DECAL, BADGE, LH IS700
Position : 2
1 DECAL, WARNING, HAND IN BELT, ENG ONLY
Position : 2
1 DECAL, CE DANGER
Position : 2
2 CLAMP, 3" ID, CUSHIONED, STAINLESS
Position : 2
2 BOLT-WHEEL 3/8-16X2.781 .750 THRD
Position : 2
6 WASHER, 5/16 F436 FLAT
Position : 2
1 NUT, 3/8-16 HEX NYLOCK FLANGE
Position : 2
2 BEARING, 6203-1/2", SEALED
Position : 2
1 FITTING
Position : 2
1 WIRE HARNESS, IS600-IS700, KAV FS (Models equipped with Kawasaki
Position : 2
4 NUT, 5/16-18 HEX NYLON LOCK
Position : 3
6 SCREW, #10-24 X 3/8 ALLEN BHBZ
Position : 3
1 SWITCH, BLADE ENGAGEMENT
Position : 3
1 KEY 1/4 SQ X 1 1/2 LONG
Position : 3
1 AIR FILTER - OUTER
Position : 3
2 SHIELD, BEARING PULLEY, 3/8ID
Position : 3
4 BODY CLIP, 1/4-20 X 1/2 DEEP
Position : 3
2 SPACER, .33 X .63 X 1.25, CZ
Position : 3
2 HYDRO RES. #71328, 350 ml
Position : 3
14 WASHER, 1/2 SAE Qty: 13 - 52" Models
Position : 3
4 WASHER, 1/2 SAE
Position : 3
1 DECAL, BADGE, RH IS700
Position : 3
2 DECAL, DANGER DO NOT OPERATE W/O DEFLECT
Position : 3
2 DECAL, DANGER, MOWER DECK, ANSI EXP
Position : 3
4 WASHER-0500(0.51IDX0.87ODX.06THK) BLK
Position : 3
16 WASHER, 3/8 SAE
Position : 3
4 SPACER, .38 X .50 X 1.25
Position : 3
1 SPACER, .51 X .75 X 1.22, PM CZ
Position : 3
2 SHIELD, TRASH
Position : 3
2 SEAL, GREASE
Position : 4
8 NUT, 5/16-18 HEX NYLOCK FLANGE
Position : 4
1 TANK, FUEL, IS500 & IS1500 - LH
Position : 4
1 PLUG, .820X1.44 HOLE, BLACK PLASTIC
Position : 4
1 PULLEY,CRANKSHAFT,1.125ID X 5.5OD A SECT
Position : 4
1 CAP - AIR CLEANER
Position : 4
1 SHIELD, PULLEY BEARING
Position : 4
4 BEARING, .375" ID X .875" OD X .341" THK
Position : 4
2 FITTING, 9/16 O-RING-1/2" HOSE, 90 DEG
Position : 4
2 SPACER, .33 X .50 X .25, CZ
Position : 4
2 SHOCK ABSORBER
Position : 4
7 NUT, 1/2-13 HEX NYLOCK FLANGE Qty: 6 - 52" Models
Position : 4
1 DECAL, FERRIS, 2.23" X 11.39"
Position : 4
1 DECAL, TRANSAXLE RELEASE, 600/700
Position : 4
2 NUT, 3/8-16 HEX SIDE LOCK
Position : 4
6 BODY CLIP, 5/16-18-7GA MATERIAL
Position : 4
8 NUT, 3/8-16 HEX SERRATED FLANGE
Position : 4
2 SPACER, .51 X .75 X .56, CZ
Position : 4
1 GREASE FITTING, 1/4-28 STRAIGHT
Position : 4
2 SPACER, IDLER ARM, 1/2 X 2.25
Position : 4
1 EYE BOLT, 3/8-16 X 8, 1 EYE
Position : 4
2 BEARING, .98 X 2.44 X .67
Position : 4
1 BATTERY CABLE, NEGATIVE, 14"
Position : 4
4 BEARING, TAPERED ROLLER,
Position : 5
6 PLUG, PANEL, 1.25 - BLACK
Position : 5
2 WASHER, 5/16 SAE
Position : 5
1 HOSE ASSEMBLY (SV)
Position : 5
1 TANK, FENDER, 1500Z - RH
Position : 5
1 CLUTCH,5218-221, WARNER
Position : 5
1 RUBBER DUST CAP
Position : 5
2 PIN, HAIR, .0915 X 1-7/8
Position : 5
2 SPACER, .39 X .55 X .38, CZ
Position : 5
4 CLAMP, HOSE
Position : 5
2 BEARING, 1/2 FLANGED, PLASTIC BALL
Position : 5
2 NUT, 1/2-13 HEX JAM Qty: 1 - 52" Models
Position : 5
1 DECAL, iCD CUTTING SYSTEM
Position : 5
2 DECAL, WARNING, ROLL BAR
Position : 5
2 DECAL, WARNING, ROLL BAR, CE
Position : 5
4 NUT, 3/8-16 HEX JAM
Position : 5
6 WHEEL- 2.00 WIDE 3.88 DIA 0.531ID POLY
Position : 5
4 NUT, 1/2-13 HEX NYLOCK FLANGE
Position : 5
2 PULLEY, FLAT IDLER, 6-3/4"
Position : 5
1 FITTING, RELIEF, 1-5 PSI
Position : 5
1 BATTERY CABLE, POSITIVE,
Position : 5
1 PIVOT BEARING-1.00 X 1.125 ODX1.50
Position : 6
1 FUEL CAP, 3-1/2", MANAGED VENT OUT, 12"
Position : 6
1 O-RING, 7/8 ID X 1/16 W
Position : 6
2 BELLEVILLE WASHER 1.1875 X .442 X .089
Position : 6
1 CAP - A/C RAIN
Position : 6
1 SPACER, .39 X .63 X 4.06, CZ
Position : 6
4 BOLT, 3/8-16 X 3/8, 1/2 SHOULDER
Position : 6
2 ROD, DUMP VALVE, IS600 (Older style rods did not have a hole for the hair pin.)
Position : 6
2 SPACER, .32 X .50 X .83, CZ
Position : 6
8 NUT, 1/2-20, FOR WHEEL BOLT SILVER
Position : 6
1 DECAL, 52 (52" Models Only)
Position : 6
1 DECAL, IGNITION SWITCH
Position : 6
4 WASHER, 5/16 SAE (Kawasaki and B&S Commercial Turf Engines)
Position : 6
2 WASHER, 1/2 USS
Position : 6
1 FLAP, 2000 REAR DISCHARGE
Position : 6
1 HOUSING, SPINDLE
Position : 6
1 STRAP-BLACK RUBB
Position : 6
1 PIVOT BEARING, 1.00 X 1.125 OD X .50
Position : 7
1 SWITCH, IGNITION, 6 POST
Position : 7
1 BOLT, CRANKSHAFT, 7/16-20 X 3, GD8
Position : 7
1 BRACKET - AIR CLEANER
Position : 7
2 NUT, 3/8-16 HEX
Position : 7
8 NUT, 3/8-16 HEX NYLOCK FLANGE
Position : 7
4 NUT, 3/8-16 HEX SIDE LOCK
Position : 7
2 SPACER, .38 X .50 X .27, CZ
Position : 7
2 TIRE/WHEEL ASM, 22X11-10,TM, .781 OFFSET (Models with 52" mower decks)
Position : 7
1 DECAL, 61 (61" Models Only)
Position : 7
1 DECAL, THROTTLE CONTROL
Position : 7
21 NUT, 5/16-18 HEX NYLOCK FLANGE
Position : 7
2 SPACER, .38 X .50 X 5.06
Position : 7
2 *PULLEY, FLAT IDLER, 6-3/4" *If not present, order 5025158 - washer and
Position : 7
3 SHIELD, PULLEY BEARING, CZ
Position : 7
1 SPACER
Position : 7
1 SOLENOID-4 POLE 12 VOLT DC (TROMBETTA)
Position : 7
1 SPACER, .75 X 1.00 X 2.38
Position : 8
10 NUT, 1/2-13 HEX NYLOCK FLANGE
Position : 8
1 CABLE, CHOKE CONTROL, 51 (Z)
Position : 8
1 HOSE
Position : 8
1 SPACER, .39 X .63 X 2.81, CZ
Position : 8
12 WASHER, 5/16 SAE
Position : 8
2 NUT, 5/16-24 HEX, LH
Position : 8
2 E-CLIP, BRAKE ARM, ZT3100 & ZT3400
Position : 8
1 GRIP, FOAM, .475 X 4.35 X .095
Position : 8
2 TIRE/WHEEL ASM, 22X11-10, TURF MASTER (Models with 61" mower decks)
Position : 8
1 DECAL, WARNING, FOLDING ROLL BAR (SV)
Position : 8
1 DECAL, SAFETY, CE ROPS (SV)
Position : 8
6 5/16 PUSH-ON NUT RETAINER, STL, CZ
Position : 8
2 CLEVIS, 5/16-18, 3/8 PIN HOLE, CLR ZINC
Position : 8
3 SHIELD, PULLEY BEARING
Position : 8
1 WASHER, 1/2 GD9 YZ
Position : 8
1 SHAFT, SPINDLE
Position : 8
2 WASHER, 5/16 LIGHT LOCK
Position : 8
12 WASHER, 1/2 SAE
Position : 9
2 WASHER, 1/4 SAE (Briggs & Stratton Commercial Turf Engines Only)
Position : 9
1 NUT, 3/8-24 HEX JAM
Position : 9
4 WASHER, .34 X 1.25 X 10 GA
Position : 9
2 CLAMP - HOSE
Position : 9
2 WASHER, 3/8 GD.9 FLAT
Position : 9
2 BRAKE ARM, ZT-3400
Position : 9
2 SPRING-COMP, .496ID X 3.00LG X .112WR
Position : 9
8 NUT, 3/8-16 HEX NYLOCK FLANGE Qty: 7 - 52" Models
Position : 9
1 DECAL, WARNING OVERHANG, ROPS (SV)
Position : 9
1 DECAL, SAFETY, CE ROPS, OBS (SV)
Position : 9
3 TIE,SELF-LOCKING, 6" (Qty: 4 on models equipped with Kawasaki Engines)
Position : 9
8 WASHER, 5/16 SAE
Position : 9
3 NUT, 3/4-16 HEX
Position : 9
1 SPACER, .39 X 1.00 X .25
Position : 9
5 NUT, 1/2-13 HEX NYLOCK FLANGE
Position : 9
3 ASSM, SPINDLE, LOW PROFILE (Nut and washer sold seperately)
Position : 9
2 NUT, 5/16-24 JAM
Position : 9
1 NUT, 3/4-16 HEX NYLON LOCK
Position : 10
4 WASHER, 5/16 SAE
Position : 10
1 SEAT, XB-180, NO LOGO, BLACK
Position : 10
1 CLAMP, VINYL INSULATED (Briggs & Stratton Engines Only)
Position : 10
1 CLUTCH ANCHOR PAD
Position : 10
1 OIL FILTER
Position : 10
4 NUT, 3/8-16 HEX NYLON LOCK
Position : 10
2 NUT, 3/8-16 HEX SERRATED FLANGE
Position : 10
2 SPACER, .39 X 1.00 X 1.25, CZ
Position : 10
1 DECAL, HYDRAULIC OIL, SAE 20W50
Position : 10
2 TIE, SELF-LOCKING, 12"
Position : 10
1 FILTER, FUEL
Position : 10
3 WASHER, 3/4 BELLEVILLE
Position : 10
1 SPACER, .39 X .75 X .38
Position : 10
1 IDLER MOUNT, .88 HIGH
Position : 10
3 WASHER, BLADE BOLT, 9/16" F436, CZ
Position : 10
2 SHOCK, SPRING ASSEMBLY
Position : 11
4 NUT, 5/16-18 HEX NYLOCK FLANGE
Position : 11
1 ASSM, SEAT PLATE W/DECALS - IS700Z (5409985B) (SV)(USA Models)
Position : 11
1 NUT, 1/4-20 HEX NYLOCK FLANGE (Briggs & Stratton Commercial Turf Engines
Position : 11
2 NUT, #10-24 HEX NYLON LOCK
Position : 11
7 NUT, 5/16-18 HEX NYLOCK FLANGE (Qty: 9 on models equipped with B&S
Position : 11
2 BEARING, BRONZE FLANGE, 3/4
Position : 11
6 BALL JOINT, 5/16-24, FEMALE
Position : 11
2 SPRING, COMPRESSION, 5-1/2
Position : 11
1 DECAL, CUT HEIGHT, IS700/ZTS700
Position : 11
1 FLAP, STRIPER, 52 DECK
Position : 11
1 FLAP, STRIPER, 61 DECK
Position : 11
5 WASHER, 1/4 SAE
Position : 11
10 WASHER, 5/16 F436 FLAT
Position : 12
1 CABLE, THROTTLE, 42" (All other models)
Position : 12
1 NUT, 5/16-18 HEX SERRATED FLANGE (LARGE)
Position : 12
1 WASHER, 1/2 SAE
Position : 12
8 NUT, 5/16-18 HEX NYLOCK FLANGE (QTY: 12 - S/N: 2016905168 & Below)
Position : 12
4 NUT, 3/8-16 HEX NYLOCK FLANGE (S/N: 2016905169 & Above)
Position : 12
2 SCREW, 5/16-18 X 1, PHILLIPS HD, BZ
Position : 12
2 NUT, 3/8-16 HEX SERRATED FLANGE Qty: 1 - 52" Models
Position : 12
1 DECAL, BELT & BLADE, IS700Z/ZTS700
Position : 12
3 PULLEY, 5.926 OVER BALL
Position : 12
1 BELT, 5V, 175.90"EL, LG ARAMID WRPD, RC
Position : 12
6 NUT, 1/4-20 HEX SERR. FLANGE
Position : 12
4 WASHER, 3/8 SAE
Position : 13
4 WASHER, 3/8 GD.9 FLAT
Position : 13
1 LEVER, THROTTLE CONTROL, HEAVY-DUTY
Position : 13
4 WASHER, 5/16 F436 FLAT (QTY: 8 - S/N: 2016905168 & Below)
Position : 13
4 WASHER, 3/8 SAE (S/N: 2016905169 & Above)
Position : 13
2 GREASE FITTING, 1/4-28 STRAIGHT
Position : 13
2 DECAL, PINCH POINT (Qty: 1 for models with 52" mower deck)
Position : 13
1 DECAL, PINCH POINT, CE
Position : 13
2 BUSHING, FLANGE
Position : 13
2 SPACER, .52 X 1.00 X .56, CZ
Position : 13
3 *PULLEY, FLAT IDLER, 6-3/4" *If not present, order 5025158 - washer and
Position : 13
3 PULLEY, FLAT IDLER, 6-3/4"
Position : 13
1 BATTERY CABLE, POSITIVE, 22 (Kawasaki and Briggs & Stratton Commercial
Position : 13
6 WASHER-3/8 FENDER
Position : 14
1 SEAT BELT, RETRACTING - ASSM
Position : 14
1 KNOB-INT THR .312-18 4-ARM 2.12WD 1.06LG
Position : 14
6 WASHER, 5/16 SAE
Position : 14
1 PULLEY, IDLER 5"OD .500ID, .75W STL
Position : 14
4 PAD, CONTROL SYSTEM
Position : 14
2 SPACER, .34 X 1.54 X .25 - UHMW
Position : 14
1 DECAL, MANUAL AVAIL IN SPANISH
Position : 14
1 DECAL, FIRE ANSI EXPORT
Position : 14
1 DUST FILTER, CANISTER (SV)
Position : 14
1 SPACER, .52 X 1.00 X 3.50
Position : 14
1 SPACER, .52 X 1.25 X .70, CZ
Position : 14
4 SHIELD, PULLEY BEARING
Position : 14
2 IDLER MOUNT
Position : 14
4 5/16 PUSH-ON NUT RETAINER, STL, CZ
Position : 14
1 BREAKER-CIRCUIT 12VOLT 20AMPS W/TAB
Position : 14
4 NUT, 3/8-16 HEX NYLOCK FLANGE
Position : 15
2 SCREW, 1/2-13 X 1.00, SHCS
Position : 15
1 SAFETY WALK, FLOOR REST, 6.00 X 16.00
Position : 15
2 TIE,SELF-LOCKING, 6"
Position : 15
1 SPACER, .52 X 1.00 X .22, CZ
Position : 15
2 PLATE, CONTROL SYSTEM ARM - HT
Position : 15
2 NUT, 1/4-20 HEX SERR. FLANGE
Position : 15
6 NUT, 1/4-20 HEX NYLOCK FLANGE
Position : 15
2 SPACER, .52 X 1.00 X 3.42
Position : 15
2 NUT, 1/4-20 HEX NYLOCK FLANGE
Position : 15
1 DECAL, CAUTION, FOLDING ROLL BAR (SV)
Position : 15
1 DECAL, DANGER DISCHARGE ANSI EXPORT
Position : 15
1 ASSEMBLY, REMOTE VENT - NO VALVE (SV)
Position : 15
1 CHUTE,DISCHARGE,RUBBER 29.00-4 HOLE,BENT
Position : 15
1 CHUTE, DISCHARGE, BEND RUBBER (SV)
Position : 15
3 IDLER MOUNT
Position : 15
26 NUT, 5/16-18 HEX NYLOCK FLANGE
Position : 15
3 CLAMP, VINYL INSULATED
Position : 15
1 SAFETY WALK, FLOOR PLATE, S50X, 10X16
Position : 16
1 CABLE, THROTTLE, 47" (Briggs & Stratton Model 541777 Vanguard Engine
Position : 16
2 SPACER, IDLER ARM, 1/2"
Position : 16
4 NUT, 1/4-20 HEX NYLOCK FLANGE
Position : 16
2 PIVOT, CONTROL SYSTEM
Position : 16
2 NUT, 5/16-18 HEX SERRATED FLANGE (SMALL)
Position : 16
4 BUSHING, FLANGE
Position : 16
1 DECAL, PARKING BRAKE SYMBOLS
Position : 16
1 GROMMET (SV)
Position : 16
1 PULLEY, DEEP V-IDLER, 6.25"OD X 1/2"ID
Position : 16
1 FUSE, ATO 15 AMP (SV)
Position : 16
2 PAD, FRICTION - 1.25 X 4.00
Position : 17
2 NUT, 1/2-13 HEX NYLON LOCK
Position : 17
2 BEARING, BALL, AXLE
Position : 17
1 WRENCH, SPANNER, CZ
Position : 17
4 BOLT, 3/8-16 X 3/4, PLT W/PATCH
Position : 17
3 NUT, 3/8-16 HEX NYLOCK FLANGE
Position : 17
4 SHIELD, PULLEY BEARING, CZ
Position : 17
1 GROMMET, 1-1/2" ID FOR 1/4" METAL
Position : 17
2 WASHER, 3/8 SAE
Position : 18
4 BOLT,HEX FLG,SER GD5 3/8-16X1-1/4PACH CZ (Models equipped with
Position : 18
1 SPACER, .52 X .84 X 1.53, PM
Position : 18
2 NUT, 7/16-14 HEX NYLON LOCK
Position : 18
8 NUT, 1/4-20 HEX NYLOCK FLANGE
Position : 18
4 WASHER, .390 X 1.50 X .109, YZ
Position : 18
2 NUT, 3/8-16 HEX NYLOCK FLANGE
Position : 19
1 GROMMET, 7/8
Position : 19
4 NUT, 5/16-18 HEX SERRATED FLANGE (LARGE)
Position : 19
2 WASHER, 1/4 FENDER
Position : 19
4 SPACER, .52 X 1.00 X .44. CZ
Position : 19
2 CLAMP, VINYL INSULATED
Position : 19
2 SPACER, .52 X 1.25 X .70, CZ
Position : 19
1 WASHER-3/8 FENDER
Position : 19
3 PULLEY, 6.93 EOD X 25MM, SPLIT
Position : 19
17 WASHER, 5/16 SAE
Position : 19
1 RELAY, 12V, 40A (Models equipped with Briggs & Stratton Vanguard Engines
Position : 19
2 CAP, LOW PROFILE, STEEL
Position : 20
2 WASHER, 1/4 SAE
Position : 20
2 WASHER, 1/4 SAE (Qty: 4 - CE Models)
Position : 20
1 ADAPTER-OIL DRAIN (Models equipped with Kawasaki Engines Only)
Position : 20
1 NUT, 1/2-13 HEX, YZ
Position : 20
6 NUT, 5/16-18 HEX NYLOCK FLANGE
Position : 20
2 COLLAR, 1/4 SET (S/N: 2016497835 & Below)
Position : 20
1 SPACER, .52 X 1.00 X .88, CZ
Position : 20
1 BELT, 5V SEC, 162.4" EL, ARAMID, WRPD, RC
Position : 20
3 NUT, 1/2-13 HEX NYLOCK FLANGE
Position : 20
1 FIR TREE MOUNT, PACKARD
Position : 20
4 WASHER, BELLEVILLE - 1.500 X .755
Position : 21
2 NUT, 1/4-20, NYLOCK FLANGE
Position : 21
2 NUT, 1/4-20, NYLOCK FLANGE (Qty: 4 - CE Models)
Position : 21
1 HOSE, OIL DRAIN
Position : 21
1 NUT, 1/2-13 HEX NYLOCK FLANGE
Position : 21
8 NUT, 5/16-18 HEX SERRATED FLANGE (SMALL)
Position : 21
2 ROD, HYDRO LINKAGE, 7.75, CZ
Position : 21
2 PIN, HAIR, .0585 X 1-1/8, 1/4 EYE, YZ (S/N: 2016497836 & Above)
Position : 21
4 INSERT, BEARING
Position : 21
1 ROD, MOUNT, CHUTE 61, CZ
Position : 21
1 SEAT SWITCH, MILSCO, BOLT-IN (SV)
Position : 21
2 NUT, 3/4-16, HEX JAM NYLON LOCK
Position : 22
1 ASSM, SEAT PLATE W/DECALS - IS700Z, ANSI-EXP (5409985B) (SV)(Export
Position : 22
1 TIE,SELF-LOCKING, 24"
Position : 22
1 PULLEY, C-SEC, V-IDLER, 6.25"ODX3/8ID
Position : 22
2 BUSHING, FLANGE 3/8ID X 7/8 LONG
Position : 22
2 ROD, CONTROL SYSTEM, IS700, CZ
Position : 22
2 CABLE, PARKING BRAKE, 31" (787.9 MM)
Position : 22
2 SPRING-EXT, 1.00 ODX13.25LGX.177WR, BLK Qty: 1 - 52" Models
Position : 22
1 SPACER, .52 X 1.00 X .56, CZ
Position : 22
1 SEAT SWITCH, MILSCO, TWIST-IN (SV)
Position : 22
4 WASHER, 3/4 SAE
Position : 23
1 LABEL, BRIGGS & STRATTON LOGO (Briggs & Stratton Powered Models - S/N:
Position : 23
1 SPACER, .39 X 1.00 X .63, CZ
Position : 23
2 SPRING, REVERSE RETURN
Position : 23
2 NUT, 5/16-18 HEX
Position : 23
1 PIN, HITCH, 1/2 X 2.00 OAL, YP
Position : 23
3 ASSM, SPINDLE, LOW PROFILE (Nut and Washer Sold Seperately)
Position : 23
1 WIRE HARNESS, VAN GRD, WARNER, IS600/700 (Models equipped with Briggs
Position : 23
4 BEARING, CUP (SV)
Position : 24
1 RUBBER, SEAT GUARD, IS700 CE (CE Models Only)
Position : 24
2 SPACER, .39 X 1.00 X .80, CZ (Models equipped with Kawasaki Engines Only)
Position : 24
1 SPACER, SHOULDER
Position : 24
2 GRIP, FOAM, 3/4 ID, 16 LONG
Position : 24
6 NUT, 3/8-16 HEX NYLOCK FLANGE
Position : 24
1 CLAMP, 5/16 DOUBLE, WIRE & TUBE (For stowing the spanner wrench.)
Position : 24
3 WASHER, 5/8 GRADE 8, YZ
Position : 24
1 SPRING, EXTENSION, SWIVEL. LONG HOOK (coil-to-coil measurement: 6-5/8"
Position : 24
1 SPRING, EXT, 1.5ODX12.25X.234WIRE BLK
Position : 24
1 BELT, 5V, 175.90EL, LG ARAMID, WRPD, RC
Position : 24
1 J-BOLT, 1/4-20 X 1-1/2, CZ (CE Models Only)
Position : 25
4 WASHER, 5/16 INT. TOOTH LOCK
Position : 25
1 WASHER, 3/8 GD.9 FLAT
Position : 25
2 BEARING, FLANGE
Position : 25
2 PAD, .77 X 3.50 X .25, POLYURETHANE
Position : 25
4 JOINT-BALL .500-20 THD .500ID, CLR ZINC
Position : 25
1 EYE BOLT, 3/8-16 X 5, 2.88THRD, 1EYE, CZ
Position : 25
3 TIE, SELF-LOCKING, 6"
Position : 25
2 NUT, 1/4-20 HEX SERR. FLANGE (CE Models Only)
Position : 26
1 EXTENSION, TAILPIPE, 3" - BLACK (B&S Commercial Turf & Model 49R977
Position : 26
4 WASHER, 1/2 GD9 YZ
Position : 26
2 ROD, DECK LIFT, 19.25
Position : 26
12 BOLT, 5/16-18 X 1 1/4 FLANGE
Position : 26
1 BELT, 5V, 162.40"EL, ARAMID WRPD, RC
Position : 26
3 WASHER, 1/2 SAE
Position : 26
3 SWITCH, DP NO/NC SNAP-IN
Position : 26
2 WASHER, .265 X 1.50 X .109, YZ (CE Models Only)
Position : 27
2 SCREW,SELF-TAP,#8-32 X 3/8, WASH HEX, CZ (B&S Commercial Turf & Model
Position : 27
1 EYE BOLT, 3/8-16 X 6, 3.0 THREAD
Position : 27
2 COLLAR, 3/8 SET
Position : 27
2 SPACER, .39 X .75 X .69, CZ
Position : 27
1 SPRING-EXT, .740 ODX2.025LGX.072WR, BLK
Position : 27
1 KIT, DISCHARGE CHUTE, 52", IS700Z - RED (SV)
Position : 27
1 EYE BOLT, 3/8-16 X 6, 3THRD, 1EYE, CZ
Position : 27
1 WIRE HARNESS, M49 VANGUARD, WARNER, 700 Models equipped with
Position : 27
1 SPRING-EXT, 1.25OD X 9.3LG X .142WR, BLK (coil-to-coil spring measurement:
Position : 28
2 EYE BOLT, 3/8-16 X 6, 3.0 THREAD (S/N: 2016528079 & Below)(Qty: 1 - 52"
Position : 28
2 EYE BOLT, 3/8-16 X 4, 2.13THRD, 1EYE, CZ (S/N: 2016528080 & Above)(Qty:
Position : 28
1 SAFETY WALK, 4.00 X 7.50
Position : 28
1 WASHER, 1/4 SAE
Position : 29
1 NUT, 3/8-16 HEX SERRATED FLANGE
Position : 29
2 NUT, 5/16-24 HEX NYLOCK LOCK
Position : 29
1 DECK SHELL W/DECALS, 52, IS700Z, ANSI-EXP (SV) (5410273B)(S/N:
Position : 29
1 DECK SHELL W/DECALS, 700-52, ANSI-EXP (SV) (5413038B)(S/N:
Position : 29
1 CLAMP, VINYL INSULATED
Position : 30
4 COLLAR, 5/8 SPLIT
Position : 30
1 BELT, A-SEC, 114.3"EL, ARAMID, WRPD
Position : 31
2 ROD, NEUTRAL RETURN
Position : 31
6 NUT, 5/16-24 HEX
Position : 31
2 ROD, SUSPENSION LINK, IS700
Position : 31
2 FLANGED BUSHING, 3/8IDX.63ODX.8125FL
Position : 32
4 GREASE FITTING, 1/4-28 STRAIGHT
Position : 32
2 DAMPENER, CONTROL,#(P6709/P3610)
Position : 33
2 WASHER, 5/16 F436 FLAT
Position : 33
8 BUSHING, 1.00 X 1.13 X 1.38, PLASTIC
Position : 33
2 NUT, 5/16-18 HEX NYLOCK FLANGE
Position : 34
2 SPACER, .33 X .625 X .360
Position : 34
1 RUBBER, FOOT PEDAL
Position : 34
2 WASHER-3/8 FENDER
Position : 35
4 PIVOT BLOCK, PLASTIC
Position : 35
2 NUT, 5/16-24 HEX NYLON LOCK
Position : 36
4 WASHER, 1/4 SAE
Position : 38
4 NUT, 1/2-20 HEX NYLON LOCK
Position : 45
4 NUT, 1/2-20 HEX JAM
Position : 46
Aubière Cedex
Position : 63178
IS700Z Series w/ 52" Side Discharge iCD Mower Deck (IS700ZB2852)
Position : 5901214
IS700Z Series w/ 61" Side Discharge iCD Mower Deck (IS700ZB2861)
Position : 5901215
IS700Z Series w/ 52" Side Discharge iCD Mower Deck (IS700ZKAV2352)
Position : 5901224
IS700Z Series w/ 61" Side Discharge iCD Mower Deck (IS700ZKAV2461)
Position : 5901225
IS700Z Series w/ 61" Side Discharge iCD Mower Deck (IS700ZBV2861)
Position : 5901226
IS700Z Series w/ 52" Side Discharge iCD Mower Deck ANSI-EXP (IS700ZB2852 ANSI
Position : 5901242
IS700Z Series w/ 52" Side Discharge iCD Mower Deck ANSI-EXP (IS700ZKAV2352 AN
Position : 5901243
IS700Z Series w/61" Side Discharge iCD Mower Deck (IS700ZB2761)
Position : 5901264
IS700Z Series w/ 52" Side Discharge iCD Mower Deck (IS700ZB2752)
Position : 5901265
IS700Z Series w/ 52" Side Discharge iCD Mower Deck (IS700ZB2752 ANSI-EXP)
Position : 5901266
IS700Z Series w/ 61" Side Discharge iCD Mower Deck (IS700ZBV2661)
Position : 5901308
IS700Z Series w/ 52" Rear Discharge iCD Mower Deck (IS700ZB2752RDCE)
Position : 5901310
IS700Z CAL Series w/ 52" Side Discharge iCD Mower Deck (IS700ZB2752 CAL)
Position : 5901385
IS700Z CAL Series w/ 52" Side Discharge iCD Mower Deck (IS700ZKAV2352 CAL)
Position : 5901386
IS700Z CAL Series w/61" Side Discharge iCD Mower Deck (IS700ZB2761 CAL)
Position : 5901387
IS700Z CAL Series w/ 61" Side Discharge iCD Mower Deck (IS700ZKAV2461 CAL)
Position : 5901388
IS700Z CAL Series w/ 61" Side Discharge iCD Mower Deck (IS700ZBV2661 CAL)
Position : 5901394