Vue éclatée Fischer mrp216517b
Découvrez la vue éclatée complète Fischer mrp216517b, un guide indispensable pour identifier facilement toutes les pièces détachées de votre appareil. Que vous soyez à la recherche d'une pièce en particulier ou simplement pour vous aider à la réparation, notre présentation détaillée vous aide à comprendre chaque composant de votre . Optimisez la maintenance et la réparation de votre appareil grâce à des schémas précis et des références adaptées. Trouvez rapidement les pièces qu'il vous faut pour prolonger la durée de vie de votre Fischer mrp216517b et éviter les pannes imprévues.
Assistant réparation
Powered by ChatGPT
Liste des pièces détachées
1 HANDLE, Upper used on All
Position : 1
1 HANDLE, Upper used on Push Models (except MR216517B)
Position : 1
1 DECK, 21” Mower Includes painted deck with decals
Position : 1
1 ASSEMBLY, Right Wheel Arm (Consists of items 2, 3, 4, 5A & 6)
Position : 1
2 BALL BEARING, 9/16” I.D.
Position : 1
2 WHEEL, 8 x 1.75 Plastic used on 2002 Model Year and Earlier
Position : 1
1 BELT, Poly-Vee
Position : 1
1 NUT, 5/16-24 Hex Lock, GR C
Position : 1
ASSEMBLY, Bag Adapter & Cover Includes items 2 thru 9; used on European
Position : 1
1 GRASS BAG, Slider Type (Black)
Position : 1
1 DECAL, Blade Control
Position : 1
2 LATCH, Frame Attachment
Position : 1
1 SCREEN, Fastener Assembly
Position : 1
1 PLUG, Chute Adapter
Position : 1
1 HANDLE, Middle- 1990 used on All
Position : 2
1 HANDLE, Middle- 1990 used on All
Position : 2
10 NUT, 5/16-18 Hex Flange Lock, GR5
Position : 2
2 BOLT, 5/16-18 Hex Washer Face Shoulder
Position : 2
3 SCREW, #10-32 x 3/8” Hex Washer Self-Tap (Torx)
Position : 2
2 WHEEL, 8 x 1.75 Plastic used on 2003 Model Year and Later
Position : 2
1 LINK, Differential
Position : 2
1 WASHER, Cone
Position : 2
1 ADAPTER, Grass Bag
Position : 2
1 ASSEMBLY, Slider
Position : 2
1 DECAL, Blade Control (Euro)
Position : 2
1 RING, Bottom
Position : 2
1 BLADE, 21” Quad Edge Ninja
Position : 2
1 HANDLE, Lower Left Hand used on All
Position : 3
1 HANDLE, Lower Left Hand used on All
Position : 3
9 BOLT, 5/16-18 x 1/2” Short Neck Carriage GR5
Position : 3
2 LATCH, Height
Position : 3
2 LATCH, Height Adjusting (Long)
Position : 3
2 NUT, 7/16-20 Hex Center Lock Jam
Position : 3
2 NUT, 7/16-20 Hex Center Lock Jam
Position : 3
1 ARM, Clutch Idler
Position : 3
1 PULLEY, Poly-Vee Belt
Position : 3
1 COVER, Bag Adapter
Position : 3
1 CONNECTOR, Grass Bag (weldment)
Position : 3
1 DECAL, Speed Select used on Self-Propelled models
Position : 3
2 ROD, Tine
Position : 3
3 NUT, 5/16-24 Hex, GR5 only 1 shown
Position : 3
1 HANDLE, Lower Right Hand used on All
Position : 4
1 HANDLE, Lower Right Hand used on All
Position : 4
1 BOLT, 5/16-18 x 1-1/8” Short Neck Carriage
Position : 4
2 GRIP, Latch
Position : 4
1 NUT, 1/4-20 Hex
Position : 4
2 BUSHING, Axle
Position : 4
2 BUSHING, Axle
Position : 4
2 PULLEY, Idler
Position : 4
2 WASHER, Spring only 1 shown
Position : 4
1 HINGE, Chute Cover
Position : 4
1 WIRE, Bag Adapter
Position : 4
1 DECAL, Speed Select (Euro) used on Self-Propelled models
Position : 4
1 SUPPORT, Wheel
Position : 4
3 WASHER, 5/16” Split Lock only 1 shown
Position : 4
1 BAIL, Blade Control used on All
Position : 5
1 BAIL, Blade Control used on All
Position : 5
3 SCREW, 3/8-16 x 1” Self-Tap (engine mounting screws)
Position : 5
6 NUT, 5/16-18 Hex Flange Lock, GR5
Position : 5
6 WASHER, 7/16 x 1” O.D. Flat Qty. of (2) for Push; Qty. of (1) for Self-
Position : 5
4 WASHER, 7/16 x 1” O.D. Flat
Position : 5
1 SCREW, 1/4-28 x 1-3/8” Hex Head Cap GR5
Position : 5
1 ASSEMBLY, Right Housing (Includes items 6, 7, 8, 9, 10 & 30)
Position : 5
5 BOLT, 1/4-20 x 1/2” Short Neck Carriage GR5
Position : 5
1 ADAPTER, Bag
Position : 5
1 DECAL, Danger, Cut Finger
Position : 5
1 TRAY, Tine
Position : 5
3 SPRING only 1 shown
Position : 5
1 CLIP, Blade Control used on All
Position : 6
1 CLIP, Blade Control used on All
Position : 6
1 SCREW, 3/8-24 x 1-3/4 Hex Head Cap GR5
Position : 6
2 RETAINER, 5/16” Bolt (Black)
Position : 6
1 ASSEMBLY, Wheel Arm, Right Rear (Round used on Push models (Incl. items 3, 10, 14,
Position : 6
2 PLUG, Wheel
Position : 6
2 PLUG, Wheel
Position : 6
1 NUT, 1/4-28 Hex Top Lock
Position : 6
1 HOUSING, Right Side
Position : 6
5 WASHER, 1/4” Internal Tooth Lock
Position : 6
1 ASSEMBLY, Grass Bag Adapter (Includes items 7 thru 14)
Position : 6
1 DECAL, Warning (Euro)
Position : 6
6 KIT, Tine Thatching Spring
Position : 6
1 CABLE, Blade Control (49-1/4” long) used on All
Position : 7
1 CABLE, Blade Control (49-1/4” long) used on MR216517B & MRP216517B
Position : 7
2 WASHER, 3/8” I.D. Cone
Position : 7
2 NUT, 5/16-18 Hex Flange Lock
Position : 7
1 ASSEMBLY, Wheel Arm, Left Rear (Square used on Push models (Incl. items 3, 11, 14,
Position : 7
2 BUSHING, 3/8” Plastic
Position : 7
3 SCREW, 5/16-24 x 1-1/8” Rib Neck, GR5
Position : 7
5 NUT, 1/4-20 Hex
Position : 7
1 ADAPTER, Bag
Position : 7
1 DECAL, Shift Warning used on Self-Propelled models
Position : 7
1 BUSHING, Wheel Adjuster
Position : 7
1 HANDLE, Wheel Drive used on Self-Propelled
Position : 8
1 HANDLE, Wheel Drive used on Self-Propelled
Position : 8
1 WELDMENT, Front Wheel Bracket
Position : 8
1 ASSEMBLY, Wheel Arm, Right Rear used on Self-Propelled models (Incl. items 1,
Position : 8
1 SHAFT, Hex Drive
Position : 8
2 SEAL, 5/8” Internal Dia.
Position : 8
1 STOP, Cover
Position : 8
1 BRACKET, Rope Pulley
Position : 8
1 DECAL, SNAPPER, 3.87 Dia. (Push)
Position : 8
1 AXLE, Wheel
Position : 8
1 GRIP, Wheel Drive Handle used on Self-Propelled
Position : 9
1 GRIP, Wheel Drive Handle used on Self-Propelled
Position : 9
1 HUB, Blade Drive 25mm
Position : 9
1 AXLE
Position : 9
1 ASSEMBLY, Wheel Arm, Left Rear used on Self-Propelled models (Incl. items 1,
Position : 9
1 PULLEY, Poly-V, 2” O.D. Non Commercial Models
Position : 9
2 BEARING, Tapered- (Differential Housing)
Position : 9
1 MOLDING, Trim
Position : 9
1 SCREW, 5/16-18 x 1-1/4” Pan Head Machine
Position : 9
1 DECAL, Warning
Position : 9
1 WHEEL, 7.00 x 1.50 Gage
Position : 9
1 CABLE, Clutch Pull (Z-Bend, 38-5/8” long) used on Self-Propelled
Position : 10
1 CABLE, Clutch Pull (Z-Bend, 38-5/8” long) used on Self-Propelled
Position : 10
1 KEY, Hi-Pro #HP506 (Briggs engine)
Position : 10
1 ARM, Round Axle End, Right Rear (Round hole) used on Push models
Position : 10
1 WASHER, 3/8” Flat
Position : 10
1 BEARING, Ball, .437 I.D. x 1.125 O.D. x .375
Position : 10
1 BUSHING, Flange
Position : 10
1 DECAL, Operator Safety
Position : 10
10 NUT, 1/4-20 Hex Top Lock only 9 shown
Position : 10
1 COVER, Vinyl used on Self-Propelled
Position : 11
1 COVER, Vinyl used on Self-Propelled
Position : 11
1 SCREW, 5/16-18 x 5/16” Hex Socket Set
Position : 11
1 ARM, Square Axle End, Left Rear (Square hole) used on Push models
Position : 11
1 SPRING, Torsion
Position : 11
1 PLUG, Housing
Position : 11
1 SPACER, .316 I.D. x .375 O.D. x .310 thick
Position : 11
1 PULLEY, Plastic
Position : 11
1 DECAL, Caution Symbols
Position : 11
4 WASHER, 1/4” Flat
Position : 11
1 SPRING, Clutch used on Self-Propelled
Position : 12
1 SPRING, Clutch used on Self-Propelled
Position : 12
1 PULLEY, Engine Drive (25mm x 2-1/8” O.D.)
Position : 12
1 ARM, Wheel, Right Rear used on Self-Propelled models
Position : 12
1 STUD, Idler (3/8-24 thread)
Position : 12
1 GEAR, Input
Position : 12
1 NUT, 5/16-18 Hex Large Flange Center Lock
Position : 12
1 NUT, 5/16-18 Hex Flange Lock GR5
Position : 12
1 DECAL, SNAPPER (Deck) silver letters, black background
Position : 12
2 SPRING, Compression
Position : 12
1 SECTOR, Speed used on Self-Propelled
Position : 13
1 BOLT, 5/16-18 x 2-1/4” Hex Flange Lock used on Euro models
Position : 13
1 ARM, Wheel, Left Rear used on Self-Propelled models
Position : 13
1 HOLDER, Bearing (Inner Half)
Position : 13
1 AXLE, Short
Position : 13
1 RETAINER, 5/16” Bolt
Position : 13
2 WASHER, 15/32” Flat
Position : 13
1 DECAL, SNAPPER silver letters, black background
Position : 13
2 BOLT, 1/4-20 x 1-1/4” Hex, GR5
Position : 13
1 BOLT, 5/16-18 x 1” Square Neck Carriage GR 5 used on All
Position : 14
1 WIRE TIE, 1.29” Long (Black) used on All
Position : 14
2 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR5 (only one shown)
Position : 14
2 BOLT, 5/16-18 x 1” Shoulder
Position : 14
1 BEARING, Ball, .38 I.D. Spherical O.D.
Position : 14
1 GEAR, Differential (46 tooth)
Position : 14
1 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR5
Position : 14
4 RIVET
Position : 14
1 DECAL, Euro Community (CE)
Position : 14
2 NUT, 1/4-20 Hex, GR5
Position : 14
1 SPRING, Speed Control used on Self-Propelled
Position : 15
1 SPRING, Speed Control used on Self-Propelled
Position : 15
2 RETAINER, 5/16” Bolt (only one shown)
Position : 15
2 RETAINER, 5/16” Bolt
Position : 15
1 O-RING
Position : 15
2 PLATE, 46T Gear
Position : 15
1 CHUTE, Side
Position : 15
1 DECAL, SNAPPER (Commercial) gold letters/red border/black background
Position : 15
2 CAP, Vinyl
Position : 15
1 WASHER, 3/8” Flat used on Self-Propelled
Position : 16
1 WASHER, 3/8” Flat used on Self-Propelled
Position : 16
3 NUT, 5/16-18 Hex Flange Lock, GR5
Position : 16
1 NUT, 3/8-24 Hex Center Lock GR5 or B
Position : 16
2 WASHER, Thrust, 3/4” I.D.
Position : 16
2 WASHER, 5/16” Flat
Position : 16
1 DECAL, Spark Plug International Symbol
Position : 16
2 BOLT, 1/4-20 x 2-1/2” Square Neck Carriage only 1 shown
Position : 16
1 GRIP, Speed Control Handle used on Self-Propelled
Position : 17
4 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap used on Euro models
Position : 17
1 BRACKET, Right Rear Wheel
Position : 17
1 HOLDER, Bearing (Outer Half)
Position : 17
4 SCREW, #10-32 x 1-1/2” Hex Head Cap GR5 only 1 shown
Position : 17
2 WING-NUT, 5/16-18 Nyloc
Position : 17
1 DECAL, Deck Warning
Position : 17
6 BOLT, 5/16-18 x 1” Square Neck Carriage, GR5 only 1 shown
Position : 17
1 DECAL, Speed Select used on Self-Propelled
Position : 18
1 WASHER, 7/16” Flat
Position : 18
1 BRACKET, Left Rear Wheel
Position : 18
1 CLIP, Transfer Rod 1/4”
Position : 18
1 GASKET, Housing
Position : 18
1 COVER, 21” Deck
Position : 18
1 DECAL, Ninja
Position : 18
2 BOLT, 1/4-20 x 3/4” Square Neck Carriage, GR5
Position : 18
1 GUIDE, Lower V-Belt used on Self-Propelled
Position : 19
1 GUIDE, Lower V-Belt used on Self-Propelled
Position : 19
1 DECAL, Operator Safety used on Euro models
Position : 19
1 AXLE Rear axle on Push Models; Front axle on All
Position : 19
1 ROD, Transfer used on Non-Euro models
Position : 19
3 WASHER, 5/16” Internal/External Tooth Lock only 1 shown
Position : 19
2 NUT, 5/16-18 Hex Large Flange Center Lock
Position : 19
1 DECAL, Patent Numbers
Position : 19
6 WASHER, Reinforcing only 1 shown
Position : 19
1 ROD, Transfer used on Self-Propelled
Position : 20
1 ROD, Transfer used on Self-Propelled
Position : 20
2 PLUG, Hole Polyethylene
Position : 20
1 GUARD, Rear Foot used on Push models
Position : 20
1 BELT, Engine Drive 3L (Stretch) used on Self-Propelled
Position : 20
1 BRACKET, Differential
Position : 20
1 DECAL, Primer (European)
Position : 20
6 WASHER, 5/16” Split Lock only 1 shown
Position : 20
1 CLIP, Transfer Rod 1/4” used on Self-Propelled
Position : 21
1 CLIP, Transfer Rod 1/4” used on Self-Propelled
Position : 21
1 GUARD, Rear Foot used on Self-Propelled models (except
Position : 21
1 PLATE, Thrust
Position : 21
4 SCREW, 1/4-20 x 1-1/4” Hex Washer Self-Tap only 1 shown
Position : 21
1 DECAL, Air Filter (European)
Position : 21
6 NUT, 5/16-18 Hex, GR5 only 1 shown
Position : 21
1 TEE-NUT, 5/16-18 used on Self-Propelled
Position : 22
1 TEE-NUT, 5/16-18 used on Self-Propelled
Position : 22
1 SPACER, Blade Hub
Position : 22
1 RING, Split (Black) used on Self-Propelled models
Position : 22
2 RING, 5/8” External Retaining used on Self-Propelled
Position : 22
1 SPACER, Axle Gear
Position : 22
1 DECAL, Deck/Chute (European)
Position : 22
2 NUT, 1/2” Push
Position : 22
1 BUSHING, Differential used on Self-Propelled
Position : 23
1 BUSHING, Differential used on Self-Propelled
Position : 23
1 WELDMENT, Fender used on Euro models
Position : 23
1 SUPPORT, Foot Guard used on Self-Propelled models
Position : 23
1 BALL BEARING, 3/4” I.D. used on Self-Propelled
Position : 23
1 AXLE, Long
Position : 23
1 DECAL, 2003 Year of Manufacture shown
Position : 23
4 BEARING, Nyliner
Position : 23
2 BOLT, 5/16-18 x 3/4” Hex Flange Lock GR5 used on All
Position : 24
2 BOLT, 5/16-18 x 3/4” Hex Flange Lock GR5 used on All
Position : 24
3 PLUG, 5/16” Square Hole used on Push models; (only one shown)
Position : 24
1 BOLT, 1/4-20 x 1/2” Short Neck Carriage GR5 used on Self-Propelled models
Position : 24
4 SCREW, #10-32 x 1/4” Self-Tap Machine
Position : 24
4 GEAR, Pinion (12 tooth)
Position : 24
1 DECAL, Chute/Deflector Warning
Position : 24
1 SCREW, 5/16-18 x 1/4” Set
Position : 24
1 SCREW, 5/16-24 x 1” Hex Head Cap GR5 used on All
Position : 25
1 SCREW, 5/16-24 x 1” Hex Head Cap GR5 used on All
Position : 25
3 PLUG, 5/16” Round Hole qty. 3 on Push, qty. 2 on Self-Propelled (only
Position : 25
1 WASHER, 1/4” Internal Tooth Lock
Position : 25
1 SHIELD, Hex Shaft used on Self-Propelled Euro
Position : 25
4 SPACER, Pinion Gear
Position : 25
1 DECAL, Noise (European)
Position : 25
2 WASHER, 1/2” Flat
Position : 25
1 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR5 used on All
Position : 26
1 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR5 used on All
Position : 26
1 WASHER, 5/16” Flat used on Euro models
Position : 26
BALL JOINT, 1/4-28 used on Self-Propelled Euro
Position : 26
4 SHAFT, Pinion
Position : 26
1 DECAL, OPEI
Position : 26
1 DECAL, Adjustment
Position : 26
10 NUT, 5/16-18 Hex Flange Lock GR5 used on All
Position : 27
10 NUT, 5/16-18 Hex Flange Lock GR5 used on All
Position : 27
2 WASHER, 7/16” Flat used on Euro models
Position : 27
1 NUT, 1/4-28 Hex GR5 used on Self-Propelled Euro
Position : 27
4 NUT, #10-32 Hex Nyloc only 1 shown
Position : 27
1 DECAL, Caution Tag not used in 2003 model year
Position : 27
1 DECAL, Thatcherizer
Position : 27
1 BRACKET, Speed Control Rod used on Self-Propelled
Position : 28
1 NUT, 5/16-24 Hex Center Lock GR5 used on All
Position : 28
1 COVER, Belt used on Euro models
Position : 28
1 LINK, Transfer used on Self-Propelled Euro
Position : 28
1 ASSEMBLY, Left Housing (Includes items 8, 9 & 29)
Position : 28
2 WIRE TIE, 1.29” Long (Black) used on All
Position : 29
1 CLIP, Cable/Wiring used on All
Position : 29
1 SCREW, 5/16-18 x 1/2” Hex Head Cap, GR5 used on Euro models
Position : 29
1 WASHER, 3/4” Shim
Position : 29
1 HOUSING, Left
Position : 29
4 SCREW, 5/16-18 x 1-7/8” Curved Head GR2 used on All
Position : 30
4 SCREW, 5/16-18 x 1-7/8” Curved Head GR2 used on All
Position : 30
1 BUSHING used on Euro models
Position : 30
3 WASHER, 3/8” Internal Tooth Lock
Position : 30
3 GASKET, 5/8” O. D.
Position : 30
4 T-KNOB, 5/16-18 (BLACK) used on All
Position : 31
4 T-KNOB, 5/16-18 (BLACK) used on All
Position : 31
1 WASHER, 3/8” Flat
Position : 31
1 LEVER, Speed Control used on Self-Propelled
Position : 32
2 SCREW, 1/4-20 x 1-1/2 Hex Head Cap GR5 used on All
Position : 32
3 NUT, 3/8-24 Hex, GR B
Position : 32
4 WASHER, 5/16” Internal Tooth Lock used on All
Position : 33
3 WASHER, 1/4” Internal Tooth Lock used on All
Position : 33
1 NUT, 5/16-18 Hex GR5 or B continued on next page
Position : 33
1 NUT, 1/4-28 Hex GR5 or B used on All
Position : 34
3 NUT, 1/4-20 Hex GR5 or B used on All
Position : 34
1 WASHER, 5/16” Split Lock
Position : 34
1 FOAM GRIP, .84 I.D. x 11” long used on All
Position : 35
1 SCREW, 1/4-20 x 2” Hex Head Cap GR5 used on All except MR216517 and
Position : 35
1 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR5
Position : 35
2 BUSHING used on All
Position : 36
2 BUSHING used on All
Position : 36
1 CONNECTOR, Transfer Rod
Position : 36
1 PIN, Clutch Handle used on Self-Propelled
Position : 37
1 PIN, Clutch Handle used on Self-Propelled
Position : 37
1 WASHER, Flat 1/4" (European Models Only) used on Self-Propelled Euro
Position : 37
1 PUSH-NUT, 1/4” (for handle pin) used on Self-Propelled
Position : 38
1 PUSH-NUT, 1/4” (for handle pin) used on Self-Propelled
Position : 38
1 BUSHING
Position : 38
1 DECAL, Blade Control (Right Hand Side) used on all (except Euro)
Position : 39
1 SPRING, Wheel Drive
Position : 39
1 GUIDE, Rope used on All
Position : 40
2 GUIDE, Rope used on All except MR216517 and
Position : 40
1 GUIDE, Thrust Plate (3/8-24 thread)
Position : 40
1 CLAMP, 7/8” Double Cable used on All
Position : 41
1 FOAM GRIP, .84 I.D. x 11” long used on All
Position : 41
1 RETAINER, 3/8” Bolt
Position : 41
1 NUT, 5/16-24 Hex Center Lock GR5 used on All
Position : 42
1 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR5
Position : 42
1 DECAL, Shift Warning used on Self-Propelled
Position : 43
1 CLAMP, Casing used on All except MR216517 and
Position : 43
1 DISC, Driven (Cantilever)
Position : 43
3 NUT, 1/4-20 Hex used on All
Position : 44
4 WASHER, 5/16” Internal Tooth Lock used on All
Position : 44
1 BRACKET, Deck
Position : 44
3 WASHER, 1/4” Internal Tooth Lock used on All
Position : 45
1 SCREW, 5/16-24 x 1-1/2” Round Hd. Machine, used on All except MR216517 and
Position : 45
2 BUSHING, Flange
Position : 45
1 SCREW, 1/4-20 x 1-3/4” Hex Head Cap GR5 used on All
Position : 46
1 CLAMP, 7/8” Double Cable used on All
Position : 46
1 SPACER used on Commercial models
Position : 46
1 SCREW, 5/16-18 x 1/2” Hex Head Cap, GR5
Position : 47
1 GUIDE, Rope used on Self-Propelled
Position : 48
1 WASHER, 5/16” Internal Tooth Lock
Position : 48
1 NUT, 1/4-20 Hex GR5 or B used on Self-Propelled
Position : 49
1 WASHER, Spring
Position : 49
1 CABLE-TIE, 7” used on Self-Propelled
Position : 50
1 PIN, 3/32 x 1/2” Cotter
Position : 50
1 SCREW, 1/4-20 x 1-1/2” Hex Head Cap, GR5 used on Self-Propelled
Position : 51
2 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
Position : 51
1 SCREW, #10-32 x 5/8” Hex Head Self-Tap used on All except MR216517 and
Position : 52
3 BOLT, 5/16-18 x 1/2” Short Neck Carriage GR5
Position : 52
1 WIRE TIE, 11” Long (Black) used on Self-Propelled
Position : 53
2 NUT, 5/16-18 Hex Flange Lock, GR5
Position : 53
1 BOLT, 5/16-18 x 1” Square Neck Carriage GR5 used on MRP216517B
Position : 54
1 SPRING, Clutch
Position : 54
1 WASHER, 1/4” Internal Tooth Lock used on Self-Propelled Euro
Position : 55
KIT, Drive Disc Assembly
Position : 56