Vue éclatée Fischer e281323bve
Découvrez la vue éclatée complète Fischer e281323bve, un guide indispensable pour identifier facilement toutes les pièces détachées de votre appareil. Que vous soyez à la recherche d'une pièce en particulier ou simplement pour vous aider à la réparation, notre présentation détaillée vous aide à comprendre chaque composant de votre . Optimisez la maintenance et la réparation de votre appareil grâce à des schémas précis et des références adaptées. Trouvez rapidement les pièces qu'il vous faut pour prolonger la durée de vie de votre Fischer e281323bve et éviter les pannes imprévues.
Assistant réparation
Powered by ChatGPT
Liste des pièces détachées
2 ASSEMBLY, Front Tire & Rim (Complete) (Includes Items 2A, 3A, 4, 5 & 6)
Position : 1
2 ASSEMBLY, Rear Tire & Rim (33” Models) (Includes 2A, 3A & 4)
Position : 1
1 ASSEMBLY, Steering Wheel (for 5/8” shaft) Includes item
Position : 1
1 WELDMENT, Main Case (Standard)
Position : 1
1 COLLAR, Lock (Includes P/N 90201 Set Screw)
Position : 1
1 ASSEMBLY, Primary Chain Case Includes Items 2 thru 13, 15,
Position : 1
1 ASSEMBLY, Smooth Clutch (Incl. items 2 thru 6) Non-Asbestos
Position : 1
1 SEAT, Operator (shown) used on 13HP & Higher Models
Position : 1
1 MUFFLER w/Heat Shield (Briggs 11 & 13HP)
Position : 1
1 WELDMENT, 5.25” O.D. Drive Disc used on 33” Deck Models
Position : 1
1 CONTROL, Throttle (23.6” long) (Briggs Engines)
Position : 1
1 COVER, Spindle
Position : 1
1 FOOT PEDAL, Blade Stop Control
Position : 1
1 BELT, Drive (73.75” AA Section) used on 33” Deck Models
Position : 1
1 ASSEMBLY, Spindle Housing (Incl. items 2 thru 13)
Position : 1
1 DECAL, Brake Operation (German)
Position : 1
1 KIT, 12 Volt Dry Charge Battery
Position : 1
1 LOGO, Steering Wheel
Position : 2
1 BALL BEARING, Axle (R.H. Fender) used on 33” Models- 13, 14 &
Position : 2
1 WELDMENT, Primary Chain Case, Right Hand
Position : 2
1 ASSEMBLY, Driven Disc Hub Was
Position : 2
1 ASSEMBLY, Fuel Tank (Includes item 3) used on 9 & 10HP Models
Position : 2
2 SCREW, 1/4-20 x 5/8” Hex Washer Head Self-Tap Was
Position : 2
2 SET SCREW, HRSS, 3/8-16 x 3/8”
Position : 2
2 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap Was
Position : 2
1 DECK, 25” Replacement (Painted deck with decals)
Position : 2
1 SPRING, Latching
Position : 2
1 NUT, 3/4-16 Hex Jam, GR
Position : 2
2 RING, 1.85” Internal Retaining
Position : 2
1 DECAL, Brake Operation (French)
Position : 2
1 SOLENOID, Super-Trombetta replaces
Position : 2
1 SOLENOID, Super-Trombetta
Position : 2
1 PIN, 1/4 x 1-1/2" Roll
Position : 3
1 FENDER, Left Hand (Standard)
Position : 3
1 GASKET, Primary Chain Case
Position : 3
1 DISC, Driven (rubber tire bonded to rim)
Position : 3
1 CAP, Fuel Tank
Position : 3
2 SET SCREW, 5/16-18 x 3/4” Socket Head, GR8
Position : 3
1 KEY,1/4” Square x 2” Long
Position : 3
1 PLATE, Throttle Control
Position : 3
1 DEFLECTOR, Discharge (Incl. items 4, 5, 6, 7 & 10) used on 25” Deck Models
Position : 3
2 ADJUSTER, Chain (5/16-18 thread)
Position : 3
1 SPRING, Pedal
Position : 3
2 WASHER, 49/64” I.D. x 1-1/2” O.D. Flat
Position : 3
2 BEARING, Spindle
Position : 3
1 DECAL, Brake Operation (Dutch)
Position : 3
1 HARNESS, Starter Wiring (Briggs Engines)
Position : 3
1 HARNESS, Starter Wiring (Briggs, AC)
Position : 3
1 HARNESS, Starter Wiring (Kohler Engines)
Position : 3
2 BALL BEARING, Flange (3/4” I.D.) per front tire ass'y.
Position : 4
1 VALVE STEM, Snap In (per rear tire ass'y)
Position : 4
1 LATCH, Parking Brake
Position : 4
1 WASHER, Thrust
Position : 4
2 WASHER, 5/8” Belleville
Position : 4
1 THRUST WASHER
Position : 4
1 HOSE, Fuel (1/4” I.D. x 8-1/2” long) used on Briggs 8-14HP
Position : 4
1 MUFFLER (Kohler 14 & 15HP)
Position : 4
1 DECAL, Danger, (Cut Finger) International Symbol
Position : 4
2 NUT, 5/16-24 Hex Was
Position : 4
1 SHOULDER BOLT, 3/8-24 w/Nylon Patch, GR5
Position : 4
1 PULLEY, Deck
Position : 4
1 WELDMENT, Spindle Housing Was
Position : 4
1 HARNESS, Ignition Wiring (Briggs Engines)
Position : 4
1 HARNESS, Ignition Wiring (14.5 B&S)
Position : 4
1 HARNESS, Ignition Wiring (15HP Kohler Engines)
Position : 4
1 VALVE STEM, Snap In per front tire ass'y.
Position : 5
1 CLAMP, R. H. (for 2” Hose) (used on 8, 10 & 13 HP) (per rear tire ass'y)
Position : 5
1 CABLE, Clutch/Brake (54.32” long) used on 25”, 28” & 30” Models
Position : 5
1 BRACKET, Drive Support
Position : 5
1 PLATE, Differential
Position : 5
2 BEARING, .625 x 1.37 x .435
Position : 5
1 PLATE, Drive Disc
Position : 5
1 FILTER, Fuel (In-Line)
Position : 5
1 GASKET, Exhaust
Position : 5
1 HINGE, Deflector
Position : 5
1 NUT, 3/8-24 Hex Nyloc
Position : 5
1 SHOULDER BOLT, 3/8-24 x 9/16”
Position : 5
1 PULLEY, Hub (Powdered Metal)
Position : 5
1 LUBE FITTING, 3/16” Press-In
Position : 5
1 DECAL, European Noise Control (100 dB)
Position : 5
1 HOLDER, Fuse (Includes Fuse)
Position : 5
1 LUBE Fitting per front tire ass'y.
Position : 6
3 BOLT, 1/2-20 x 3/4” Lug, GR5 (per rear tire ass'y)
Position : 6
2 WASHER, 3/8” Flat SAE
Position : 6
2 BOLT, 5/16-18 x 3/4” Hex Flange Lock, GR5
Position : 6
4 SPACER, Pinion
Position : 6
1 WELDMENT, Sprocket & Shaft
Position : 6
4 NUT, 5/16-18 Hex Flange Lock, GR5 Was
Position : 6
4 CLAMP, Fuel Line replaces 12222 clamp
Position : 6
2 SPACER, .33 x .63 x .156
Position : 6
1 SPRING, Hinge
Position : 6
1 WASHER, 3/8” Flat SAE
Position : 6
1 WASHER, Flat 13/32" ID x 1.25" x 1/8" Thick ZP Was
Position : 6
2 NUT, 3/8-16 Hex Nyloc
Position : 6
1 SPINDLE, Shaft (10.237" Long)
Position : 6
1 DECAL Safety Instructions (French/German)
Position : 6
1 INTERLOCK MODULE, Briggs Was
Position : 6
1 INTERLOCK MODULE, Briggs & Kohler Was
Position : 6
2 WASHER, .77 x 1.13 x .06 Flat per front tire ass'y.
Position : 7
1 BOOT, Right Hand (8 & 10 HP) (per rear tire ass'y)
Position : 7
1 PAD, Pedal
Position : 7
2 CAP, Bumper
Position : 7
4 GEAR, Differential Pinion (12T 12P)
Position : 7
1 KEY,#5 Woodruff
Position : 7
1 ASSEMBLY, Brake Lever (Includes brake pad & rivet)
Position : 7
1 BRACKET, Fuel Tank (Rear)
Position : 7
1 NUT, 1/4-20 Hex Flange Lock Was
Position : 7
1 PIN, Hinge
Position : 7
1 PIVOT, Leveling
Position : 7
1 NUT, 3/8-24 Hex, GR B Was
Position : 7
2 IDLER PULLEY, 4” Idler
Position : 7
1 WASHER, .77 x 1.13 x .06 Flat
Position : 7
1 DECAL, Euro Community (CE)
Position : 7
1 HARNESS (Deck Interlock Wiring)
Position : 7
1 HUB CAP per front tire ass'y.
Position : 8
1 SEAL (per rear tire ass'y)
Position : 8
1 BUSHING, Nylon
Position : 8
6 NUT, 5/16-18 Hex Flange Lock, GR5 Was
Position : 8
1 WASHER, Thrust
Position : 8
1 CHAIN CASE HALF, Primary
Position : 8
1 RING, 3/8” External Retaining
Position : 8
2 SCREW, 5/16-18 x 1/2” Pan Head Self-Tap (Torx #T-40)
Position : 8
1 HEAT SHIELD, Muffler
Position : 8
1 NUT, 5/16-18 Hex Flange Lock, GR5 Was
Position : 8
1 WELDMENT, Rear Lift Arm
Position : 8
2 WASHER, 1/2” Flat SAE
Position : 8
2 SCREW, 3/8-16 x 1-1/2” Hex Head Cap, GR5
Position : 8
1 WASHER, Spindle
Position : 8
1 DECAL, Deflector French/German
Position : 8
1 FELT SEAL per front tire ass'y.
Position : 9
1 HUB, Rear Wheel R. H. (Weldment) (per right rear tire ass'y)
Position : 9
1 WELDMENT, Clutch Pedal
Position : 9
1 NUT, 5/16-24 Flange Lock (Large)
Position : 9
1 ASSEMBLY, Drive Hex Tube
Position : 9
2 BEARING, Needle
Position : 9
1 NUT, 1/4-28 Hex Top Lock
Position : 9
2 WASHER, 1/4” Split Lock
Position : 9
1 NUT 1/4-20 Hex Flange Lock Was
Position : 9
1 SCREW, 3/8-24 x 1-3/4” Hex Head Cap, GR5
Position : 9
1 BRACKET, Fixed Idler used on 33” Deck Models only
Position : 9
1 HOLDER, Blade
Position : 9
1 DECAL, Battery Storage
Position : 9
1 COVER, Battery Cable
Position : 9
1 CAP, Dust per front tire ass'y.
Position : 10
1 CAP, Hub (per rear tire ass'y)
Position : 10
4 BEARING, Nylon
Position : 10
1 SHIFT LINK, Long
Position : 10
1 WASHER, Nylon
Position : 10
2 THRUST WASHER, Nylon
Position : 10
1 WASHER, .28 x .63 x .06 Flat, GR5
Position : 10
2 SPACER, .33 x .63 x .156
Position : 10
2 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap
Position : 10
2 PUSH NUT, 1/4”
Position : 10
2 WASHER, 13/32 x 1-1/4” Flat
Position : 10
1 NUT, 1/4-20 Hex Flange Lock, GR5
Position : 10
1 BRACE, Fixed Idler Bracket used on 33” Deck Models only
Position : 10
1 SPACER, Blade Centering
Position : 10
1 DECAL Safety Instructions (English/Dutch)
Position : 10
1 WIRE, Positive (Red, 17” long)
Position : 10
1 COTTER PIN, 5/32 x 1” per front tire ass'y.
Position : 11
1 CAP, Hub, L. H. (Long Axle) (per left rear tire ass'y)
Position : 11
1 WELDMENT, Steering Shaft
Position : 11
1 WELDMENT, Shift Arm
Position : 11
1 GEAR, 11 Tooth, 10 Pitch
Position : 11
1 WELDMENT, Hub & Sprocket
Position : 11
1 SPACER, Brake Arm Pivot
Position : 11
1 VALVE, Fuel Shut-Off (Accessory) Was
Position : 11
1 SCREW, 1/4-20 x 3/4” Hex Head Cap, GR5
Position : 11
3 BOLT, 3/8-16 x 3/4” Hex Flange Lock Was
Position : 11
1 LEVER, Height of Cut
Position : 11
1 CABLE ASSEMBLY, No Reverse in Mow
Position : 11
5 SCREW, 5/16-18 x 1/2” Hex Washer Self-Tap
Position : 11
1 NUT, 5/8-18 Hex Center Lock Jam
Position : 11
1 DECAL, Deck/Chute International Warning
Position : 11
1 SWITCH, Ignition, 4 Terminal, Indak
Position : 11
1 SWITCH, Ignition-Afterfire Solenoid
Position : 11
1 TUBE, Inner (For 4.10/3.50 x 4 Tire) per front tire ass'y.
Position : 12
1 HUB, Rear Wheel L. H. (Weldment) (per left rear tire ass'y)
Position : 12
4 BUSHING, Tie Rod
Position : 12
1 CROSS BRACE
Position : 12
1 CHAIN, 46 Pitch (#35 Endless)
Position : 12
1 CHAIN, 46 Pitch (#35 Endless)
Position : 12
1 SCREW, 1/4-28 x 1” Hex Head Cap, (Washer Face) GR5
Position : 12
2 BOLT, 5/16-18 x 1/2” Hex Flange Nyloc
Position : 12
1 MUFFLER GUARD, Kohler
Position : 12
2 SCREW, 1/4-20 x 3-1/2” Hex Head w/Free Spinning Washer
Position : 12
1 NUT, 3/8-24 Hex Center Lock
Position : 12
1 CLIP, Cable
Position : 12
1 HANDLE, Blade Engagement (Flip)
Position : 12
2 SCREW, 1/2-20 x 1-1/4” Hex Head Cap, GR5
Position : 12
1 DECAL, Clutch Brake
Position : 12
1 WASHER, 5/8” Internal Tooth Lock Was
Position : 12
1 NUT, 5/16-24 Hex Lock, GR C Was 11201 (per rear tire ass'y)
Position : 13
1 TIE ROD, Left Hand (7.41” long)
Position : 13
1 SHFT LINK, Short (5/16-24 thread)
Position : 13
1 SPROCKET, 34T, 3/8P
Position : 13
10 SCREW, #10-24 x 1/2" Hex Washer Self-Tap (Torx) Was
Position : 13
1 SPRING, Torsional Brake Return
Position : 13
1 BRACKET, Muffler Guard (Kohler)
Position : 13
2 WASHER, 5/16” Flat Was
Position : 13
1 SPRING, Lever
Position : 13
1 BOLT, 1/4-20 x 3/4” Square Neck Carriage, GR5 Was
Position : 13
2 RING, 2” External Retaining
Position : 13
2 NUT, 1/2-20 Hex, GR5 or B
Position : 13
1 DECAL, Battery Caution, Multi-Language
Position : 13
1 NUT, 5/8-32 Hex
Position : 13
1 AXLE BOLT, Left Hand (per left rear tire ass'y)
Position : 14
1 KING PIN Weldment, Left Hand
Position : 14
1 NUT, 5/16-18 Hex, GR 5 or B Was
Position : 14
1 RING, 1-3/16” External Retaining
Position : 14
1 PLUG, 1/2” Cup Insert
Position : 14
1 SPRING, Clutch & Brake
Position : 14
1 HOSE, Fuel (1/4” I.D. x 3-1/2” long)
Position : 14
1 SCREW, 1/4-20 x 1” Hex Head Cap, GR5 Was
Position : 14
1 BOLT, 1/4-20 x 1/2” Hex Flange Lock
Position : 14
2 RING, Rear Lift Arm (Blue)
Position : 14
3 PIN, 3/32 x 3/4” Cotter Was
Position : 14
1 DECAL, Patent Numbers
Position : 14
1 IGNITION KEY, Pair
Position : 14
1 WHEEL BOLT, Right Hand (per right rear tire ass'y)
Position : 15
1 TIE ROD, Right Hand (7.41” long)
Position : 15
1 WELDMENT, Arm, Shift Handle
Position : 15
1 SPACER, Differential Case
Position : 15
1 ROLLER, 1-3/8 Long
Position : 15
1 LIFT, Yoke
Position : 15
2 BRACKET, Seat
Position : 15
2 SCREW, 1/4-20 x 5/8” Hex Head w/Free Spinning Washer Was
Position : 15
1 KIT, Air Lift used on 25”, 28” & 33” Decks
Position : 15
1 GUIDE, Belt
Position : 15
1 SPRING, Extension, 4” x 1/2” Diameter
Position : 15
1 DECAL Deflector Caution (English/Dutch)
Position : 15
3 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap Was
Position : 15
1 KING PIN Weldment, Right Hand
Position : 16
1 SPRING, Shift Detent
Position : 16
2 BOOT CLAMP (for 2” Hose)
Position : 16
1 RING, 1/2” External Retaining (Heavy Duty)
Position : 16
2 BEARING, Yoke
Position : 16
4 BOLT, 5/16-18 x 1” Square Neck Carriage, GR5
Position : 16
2 AIR-LIFT (33” Models)
Position : 16
2 SPRING, Assist
Position : 16
1 WELDMENT, Idler Arm
Position : 16
1 DECAL, 28 Inch (Hi-Vac)
Position : 16
1 SWITCH, Operator Presence Control (OPC) Traction (NC/NO)
Position : 16
1 WELDMENT, Front Axle, Narrow used on 25”, 28” & 30” Models
Position : 17
1 ASSEMBLY, Speed Adjustment Latch Includes Spring, Part Number
Position : 17
1 BOOT, Oil Seal (Short Axle)
Position : 17
1 FENDER, Left Hand (1.628” I. D. Hole) used on 25” & 28” Deck Models
Position : 17
2 NUT, 5/16-24 Hex Center Lock Was
Position : 17
2 NUT, 5/16-18 Hex Flange Top Lock
Position : 17
2 WASHER, .28 x .63 x .06 Flat, GR5
Position : 17
6 SCREW, 5/16-24 x 11/16” Oval Head Machine
Position : 17
1 BRACE, Top
Position : 17
1 SPACER, .39 x 1.0 x .31 Nylon
Position : 17
1 DECAL, 33 Inch (Hi-Vac)
Position : 17
5 NUT, 1/4-20 Hex, GR5 or B
Position : 17
1 HARNESS WIRE, Operator Presence Control (OPC)
Position : 17
4 NUT, 1/4-20 Hex Was
Position : 17
2 FOOT PAD, Short
Position : 18
1 WELDMENT, Shift Handle
Position : 18
1 PLUG, 1/2” Cup Insert
Position : 18
1 COLLAR, Lock (Incl. P/N 90776 Set Screw, 1/4-20 x 1/4”) used with ball bearing, item
Position : 18
2 SCREW, 5/16-24 x 1” Hex Head Cap, GR5
Position : 18
6 WASHER, 5/16” Internal Tooth Lock
Position : 18
1 ROD, Leveling (3/4-24 thread)
Position : 18
1 GRIP, Handle
Position : 18
1 DECAL, Back-Up Recoil (33” Kohler Engine Models)
Position : 18
2 WASHER,1/4” Internal Tooth Lock
Position : 18
1 SPRING, Parking Brake Latch
Position : 19
2 HAIR PIN, 3/32 x 1-1/2”
Position : 19
1 CASE, Transmission
Position : 19
1 BEARING, Left Hand Fender (Includes item 20) used on 25” & 28” Models- 8,
Position : 19
1 SCREW, 3/8-16 x 5/8” Hex Washer Self-Tap
Position : 19
6 NUT, 5/16-24 Hex Was
Position : 19
1 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
Position : 19
2 WASHER, 3/8” Flat Was
Position : 19
1 DECAL, OHV (33” Kohler Engine Models)
Position : 19
2 SCREW, 1/4-20 x 5/8” Hex Head Cap. GR5 Was
Position : 19
2 SCREW, 1/4-20 x 5/8” Hex Head Cap. GR 5 Was
Position : 19
2 SCREW, 1/4-20 x 5/8” Hex Head Cap, GR5 Was
Position : 19
2 WASHER, .66 x 1.31 x .09 Flat
Position : 20
1 GRIP, Shift Handle
Position : 20
1 GASKET, Transmission Case
Position : 20
1 FITTING, Lube, 45 Degree, 3/16” w/Hex
Position : 20
1 COLLAR, Yoke
Position : 20
2 SCREW, 1/2-20 x 1” Hex Head Cap, GR5
Position : 20
1 ASSEMBLY, Clutch Plate
Position : 20
1 DRUM, Brake Spindle
Position : 20
1 DECAL, SNAPPER
Position : 20
1 WIRE, Negative, Black (15” long)
Position : 20
2 BUSHING, Nylon
Position : 21
2 WING, Rear
Position : 21
1 FENDER, Right Hand (2.498” Dia. Hole) 33” Deck Ball Bearing
Position : 21
1 TIE ROD (5/16-24 thread- both ends)
Position : 21
2 FENDER WASHER, 5/16”
Position : 21
2 WASHER, 1/2” Internal Tooth Lock
Position : 21
1 RAIL, Deck Lift, Right Hand Was
Position : 21
1 PIN, 1/4 x 1-5/8” Clevis
Position : 21
1 DECAL, Brake Operation (Italian)
Position : 21
1 HARNESS, Operator Presence Control (OPC) Wire
Position : 21
2 NUT, 1/4-20 Hex, GR 5 or B attaches to starter terminal
Position : 21
1 HARNESS, Operator Presence Control (OPC) Wire
Position : 21
1 HAIR PIN 2-1/4”
Position : 22
1 BUSHING, Pilot Was
Position : 22
1 GEAR, 63 Tooth 10 Pitch
Position : 22
1 ARM, Yoke
Position : 22
2 NUT, 1/2-20 Hex Jam
Position : 22
1 RAIL, Deck Lift, Left Hand
Position : 22
1 BAND, Brake (Formed)
Position : 22
1 DECAL, Brake Operation (Spanish)
Position : 22
2 RETAINER, 1/4” Bolt
Position : 22
1 NUT, 1/4-20 Hex, GR5 or B
Position : 22
1 FOAM COVER, Steering Shaft
Position : 23
1 BRACKET, Switch
Position : 23
1 AXLE, Long Was
Position : 23
1 BOOT, Rear Axle, Thick Flange
Position : 23
2 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap Was
Position : 23
2 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR5
Position : 23
1 DETENT, Height Adjust
Position : 23
1 DECAL, Height of Cut
Position : 23
2 CABLE TIE, 7”
Position : 23
2 NUT, 1/4-20 Hex Center Lock, GR 5 or B
Position : 23
1 PIN, 3/16 x 1” Cotter
Position : 24
1 PIN, 3/32 x 3/4” Cotter Was
Position : 24
1 SPACER, Differential Case
Position : 24
1 THRUST WASHER
Position : 24
1 STUD, Clutch Link (3/8-24 thread)
Position : 24
4 SCREW, 1/4-20 x 5/8” Hex Head w/Free Spinning Washer Was
Position : 24
2 SCREW, 3/8-16 x 1” Hex Washer Self-Tap
Position : 24
4 WASHER, 1/4” Flat Was
Position : 24
1 DECAL, Service Parts, Euro
Position : 24
2 NUT, 1/4-20 Hex Center Lock, GR5 or B
Position : 24
2 WASHER, 3/8” Flat Was
Position : 25
1 PIN, 1/4 x 1-3/4” Tapered Clevis
Position : 25
1 ASSEMBLY, Short Axle, 23T (Includes Gear) Use only with Long Axle P/N
Position : 25
1 WASHER, 3/8” Internal Tooth Lock
Position : 25
3 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR5 Was
Position : 25
1 SPACER, Detent
Position : 25
1 EYE-BOLT, 1/4-20 x 4”
Position : 25
1 DECAL, Caution, Fuel Leakage (English)
Position : 25
1 CABLE TIE, 3.19” long
Position : 25
1 SWITCH, Seat (Normally Closed)
Position : 25
1 PIN, 3/16 x 1-1/2” Cotter Was
Position : 26
1 BUSHING, 3/4 x 1.62 Flange (Nylon)
Position : 26
4 BOLT, 5/16-24 x 1-5/8” Hex Special Lock (Vibresist)
Position : 26
1 NUT, 5/8-18 Hex Nyloc
Position : 26
1 NUT, 3/8-24 Hex, GR5 or B
Position : 26
1 COVER, 25” Mulcher
Position : 26
3 SCREW, 3/8-16 x 5/8” Hex Washer Self-Tap
Position : 26
1 SPRING, Torsion, Flip Handle
Position : 26
1 DECAL, Caution, Fuel Leakage (Dutch)
Position : 26
1 SWITCH, Seat (NC) used on 11 & 13HP Engines
Position : 26
1 SWITCH, Seat (NC)
Position : 26
2 PIN, 5/32 x 1” Cotter Was
Position : 27
2 WASHER, Thrust
Position : 27
2 O-RING, 5/16"
Position : 27
1 BRACKET, Slide
Position : 27
9 NUT, 3/8-16 Hex Flange Lock Was
Position : 27
1 GRIP, Height Adjustment Lever
Position : 27
1 PIN, 3/16 x 1” Clevis
Position : 27
1 DECAL, Caution, Fuel Leakage (German)
Position : 27
1 RING, 1/2” External Retaining (Heavy Duty)
Position : 28
2 BUSHING, 3/4 x I.O. Flange (Nylon)
Position : 28
2 WASHER, 5/16” Belleville
Position : 28
2 O-RING, 1/2 x 5/8”
Position : 28
1 PIN, 3/32 x 3/4” Cotter Was
Position : 28
3 NUT, 3/8-24 Hex Nyloc
Position : 28
2 RING, Front Lift Arm (Red)
Position : 28
1 WELDMENT, Blade Engagement Handle
Position : 28
1 DECAL, Caution, Fuel Leakage (French)
Position : 28
2 RING, 5/8” External Retaining
Position : 29
14 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
Position : 29
1 WASHER, 5/16” External Tooth Lock
Position : 29
1 SPACER, Nylon
Position : 29
2 SLIDE HALF
Position : 29
3 SCREW, 3/8-24 x 3-3/4” Hex Head Cap, GR5
Position : 29
1 ARM, Front Lift
Position : 29
1 SPRNG, Blade Handle
Position : 29
1 DECAL, Caution, Fuel Leakage (Italian)
Position : 29
2 PIN, 1/8 x 3/4” Cotter Was
Position : 30
2 SCREW, #10-32 x 1/4” Hex Washer Self-Tap
Position : 30
1 WASHER, .34 x .69 x .08 Flat
Position : 30
1 WASHER, Shim or quantity as required
Position : 30
1 BOLT, 5/16-18 Shoulder
Position : 30
3 WHEEL, Gage
Position : 30
1 WELDMENT, Front Lift Arm
Position : 30
1 ROD, Idler Control
Position : 30
1 DECAL, Caution, Fuel Leakage (Spanish)
Position : 30
6 WASHER, .77 x 1.13 x .06 Flat
Position : 31
4 WASHER, 5/16” Flat Was
Position : 31
1 SCREW, 5/16-24 x 2-5/8” Hex Head Cap
Position : 31
6 WASHER, Shim .625 x .875
Position : 31
1 WASHER, 5/16” Split Lock
Position : 31
3 SPACER
Position : 31
1 PIN, 1/8 x 3/4” Cotter Was
Position : 31
1 SCREW, #10-32 x 1” Hex Washer Head Self-Tap
Position : 31
1 DECAL, Safety Instructions (Spanish/Italian)
Position : 31
1 COVER, Steering Shaft
Position : 32
1 CLIP, Wire
Position : 32
11 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
Position : 32
1 BALL BEARING, Left Hand Fender for 33” Deck Models
Position : 32
1 NUT, 5/16-18 Hex, GR 5 or B Was
Position : 32
1 BRACKET, Gage Wheel (Front)
Position : 32
1 ROD, Deck Support (Front Lift Arm to Front End)
Position : 32
1 SWITCH, Deck Interlock (NO)
Position : 32
1 DECAL, No Mow in Reverse (Euro)
Position : 32
1 HOLDER, Bottle (Wire)
Position : 33
1 WASHER, 5/16” Internal Tooth Lock
Position : 33
13 SCREW, 1/4-20 x 5/8” Hex Washer Head Self-Tap Was
Position : 33
GREASE, Transmission (Use 2 oz. Maximum)
Position : 33
2 BRACKET, Gage Wheel (Rear)
Position : 33
1 RING, .438 External Retaining
Position : 33
1 MOUNT, Handle/Switch
Position : 33
1 DECAL, Engine, B&S E10 Powerbuilt
Position : 33
2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap (Torx)
Position : 34
4 SCREW, 5/16-18 x 1-1/2” Hex Washer Self-Tap Was
Position : 34
1 SPACER, Short Axle
Position : 34
1 ASSEMBLY, Leaf Spring
Position : 34
6 BOLT, 5/16-18 x 1/2” Short Neck Carriage, GR5
Position : 34
2 SCREW, 5/16-18 x 1/2” Hex Washer Self-Tap
Position : 34
2 SCREW, 1/4-20 x 5/8” Hex Washer Head Self-Tap Was
Position : 34
1 BOTTLE, Water
Position : 35
4 SCREW, 5/16-24 x 1-3/4” Hex Head Cap, GR5
Position : 35
GREASE, Transmission (24 oz. Required)
Position : 35
8 NUT, 5/16-18 Hex Flange Lock, GR5 Was
Position : 35
2 SPACER, Deck Lift
Position : 35
1 PIN, 3/32 x 1/2” Cotter Was
Position : 35
1 CABLE, Brake (29” long)
Position : 36
4 RETAINER, 5/16” Bolt
Position : 36
2 NUT, 5/16-18 Wing Was
Position : 36
1 BOLT, #10-24 x 1” Flat Head Square Neck
Position : 36
1 NUT, 1/4-20 Hex Top Lock Was
Position : 36
2 CONNECTOR, Cable
Position : 37
1 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR5 Was
Position : 37
1 BLADE, 25” Mulcher
Position : 37
1 NUT, #10-24 Hex Nyloc
Position : 37
1 BUSHING, Flange .27 x .35 x .4
Position : 37
1 SCREW, 1/4-20 x 3/4” Hex Head Cap, GR5
Position : 38
4 SCREW, 5/16-18 x 3/4” Hex Washer Self-Tap
Position : 38
1 BLADE, 25”
Position : 38
1 ANCHOR
Position : 38
1 SPRING, Rectangular Wire Die, Blue
Position : 38
1 NUT, 1/4-20 Hex Center Lock, GR5 or B
Position : 39
2 SWIVEL, Adjustable
Position : 39
1 BLADE, Ninja, 25”
Position : 39
2 SCREW, 5/16-24 x 3/4” Hex Head Cap, GR5
Position : 39
1 RESTRICTOR, Belt
Position : 39
1 COVER, Switch
Position : 40
2 WASHER, 5/16” Internal Tooth Lock
Position : 40
1 COVER, Battery
Position : 41
7 FASTENER, 1/4” Ratchet
Position : 42
1 SHOULDER BOLT, 5/16-18
Position : 43
1 LEVER, Over-Ride
Position : 44
1 WASHER, .47 x .92 x .065 Flat
Position : 45
1 NUT, 5/16-18 Hex Nyloc
Position : 46
1 OIL DRAIN, Short
Position : 47
1 ASSEMBLY, Oil Valve
Position : 48
1 PLATE, Engine (Kohler Engine) used on E331523KVE Model
Position : 49
7 WASHER, .32 x .58 x .08 Split Lock
Position : 50
1 WASHER, .32 x .58 x .08 Split Lock
Position : 50
1 BOLT, M8-1.25 x 25mm, Self-Tap (Kohler)
Position : 51
4 SCREW, 5/16-24 x 1” Hex Head Cap, GR5
Position : 52
7 NUT, 5/16-24 Hex, GR5
Position : 53
1 NUT, 5/16-24 Hex, GR5
Position : 53
1 TUBE CLAMP
Position : 54
1 SCREW, 5/16-24 x 2-1/2” Hex Head Cap, GR5
Position : 55
2 PLUG, 1/2” Cup Insert
Position : 7011024
1 BUSHING, Tie Rod
Position : 7013321
2 BUSHING, Tie Rod
Position : 7013321
2 KNOB, Seat Adjusting (5/16-18 thread)
Position : 7023191
2 KNOB, Seat Adjusting, 5/16-18 thread
Position : 7023735
2 SPACER, Pivot
Position : 7028395
1 SWITCH, Seat (NC)
Position : 7029211
1 KIT, Tire Chains (16 x 4.50-8 Tires) Was 60358 (All Rear Engine
Position : 7060049
1 KIT, Drive Disc Puller used on All RER Aluminum
Position : 7060325
1 KIT, Tire Chains (16 x 6.50-8 Tires) used on All Rear Engine Riders
Position : 7060357
1 KIT, Wheel Weight (8” Wheels) used on All Rear Engine Riders
Position : 7060517
1 KIT, Dump Cart used on All Rear Engine Riders
Position : 7060697
1 KIT, Gage Wheel used on All 33” Deck Rear
Position : 7060737
1 KIT, Single Bag Catcher used on All 25” Deck Rear
Position : 7060941
1 KIT, Single Bag Catcher used on All 28” & 33” Deck Rear
Position : 7060943
1 KIT, Bag-N-Wagon used on All 28” & 33” Deck Rear
Position : 7060947
1 KIT, 28” Thatcherizer used on All series 7 & Newer
Position : 7060948
1 KIT, 36” Dozer Blade used on All Rear Engine Riders
Position : 7060959
1 KIT, Wagon Cover used on All 28” & 33” Deck Rear
Position : 7060964
1 KIT, Ninja Recycling Cover used on All 25” Deck Rear
Position : 7061049
1 KIT, Ninja Recycling Cover used on All 28” Deck Rear
Position : 7061253
1 KIT, Ninja Recycling Cover used on All 33” Deck Rear
Position : 7061255
1 KIT, Twin Bag Catcher used on All 28” & 33” Deck Rear
Position : 7063281
1 KIT, Front Weight Was 61190 (used on All series
Position : 7072416
2 NUT, 5/16-18 Hex Large Flange Center Lock
Position : 7090951
4 BOLT, 5/16-18 x 1/2” Hex Flange Nyloc
Position : 7091038
2 PIN, 5/32 x 1” Cotter
Position : 7091516