Vue éclatée Fischer i8245e
Découvrez la vue éclatée complète Fischer i8245e, un guide indispensable pour identifier facilement toutes les pièces détachées de votre appareil. Que vous soyez à la recherche d'une pièce en particulier ou simplement pour vous aider à la réparation, notre présentation détaillée vous aide à comprendre chaque composant de votre . Optimisez la maintenance et la réparation de votre appareil grâce à des schémas précis et des références adaptées. Trouvez rapidement les pièces qu'il vous faut pour prolonger la durée de vie de votre Fischer i8245e et éviter les pannes imprévues.
Assistant réparation
Powered by ChatGPT
Liste des pièces détachées
2 NUT, 5/16-18 Hex Nyloc
Position : 1
1 PUSH NUT, Pal. .375 Dia. Stud Cap
Position : 1
1 END PLATE, RH- Auger Housing- Red
Position : 1
1 CHUTE, Discharge A Chute/Deflector Assembly
Position : 1
1 PULLEY, Auger Input
Position : 1
3 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap or
Position : 1
4 SCREW, 5/16-24 x 3/4” Hex Head Cap, GR 5 or
Position : 1
4 SCREW, 5/16-24 x 1-1/4” Hex Head Cap, GR
Position : 1
2 KLIK- PIN, .310 ID x 1-3/4” Long
Position : 1
1 DECAL, Dashboard- RH used on Domestic Models
Position : 1
1 DECAL, Dashboard- RH- Euro
Position : 1
1 STRAP, Ground (not shown) B&S #
Position : 1
1 BRACKET, Snow Stick- Lower
Position : 2
1 KNOB, Spinner
Position : 2
1 WELDMENT, Auger Housing - 22” - Red
Position : 2
1 WELDMENT, Auger Housing - 24” - Red
Position : 2
1 SCREW, 5/16-24 x 3/4” Hex Head Cap, GR
Position : 2
2 SET SCREW, 5/16-18 x 1/2” Square Head Cup Point or
Position : 2
1 BRACKET, Bushing
Position : 2
1 WASHER, 5/16” Flat
Position : 2
1 VALVE STEM AND CAP per tire assembly
Position : 2
1 DECAL, Shift Pattern
Position : 2
1 CLAMP, Regulator (not shown) B&S #
Position : 2
4 SCREW, 5/16-18 x 3/4” Hex Head Cap or
Position : 3
3 BUSHING, .376 x .437 x .20
Position : 3
3 RETAINER NUT, 5/16-18
Position : 3
1 DEFLECTOR, Chute
Position : 3
2 KEY, 3/16 x 3/4” Woodruff or
Position : 3
1 NUT, 3/8-16 Hex, GR 5 or B
Position : 3
1 WIRE, Belt Stop replaced by 7100117 &
Position : 3
1 TUBE, Tire per tire assembly (optional)
Position : 3
1 DECAL, Dashboard- LH used on Domestic Models
Position : 3
1 DECAL, Dashboard- LH- Euro
Position : 3
1 BRACKET, Regulator (not shown) B&S #
Position : 3
1 CLUTCH CABLE, Auger Drive- RH parts number is stamped on
Position : 4
1 ROD, Chute, Upper
Position : 4
1 END PLATE, LH- Auger Housing- Red
Position : 4
1 WING KNOB, 5/16-18
Position : 4
1 SET SCREW, 3/8-16 x 1/2” Square Head
Position : 4
1 WASHER, 3/8” Split Lock or
Position : 4
3 LOCKWASHER, 5/16” Exterior Tooth or
Position : 4
3 LOCKWASHER, 5/16” Exterior Tooth or
Position : 4
1 RIM, 6 x 3.25 (Weldment) per tire assembly
Position : 4
1 DECAL, Dash Front - SNAPPER
Position : 4
1 SCREW, Hex Head B&S #
Position : 4
1 HANDLE, Upper, Right Hand
Position : 5
1 CLIP, .093 Dia. Hair Pin
Position : 5
1 BLADE, Scraper- 22” replaces
Position : 5
1 BLADE, Scraper- 24” replaces
Position : 5
1 WIRE PIN
Position : 5
1 WELDMENT, Impeller
Position : 5
1 ASSEMBLY, Shift Arm w/Bushing includes weldment (1666213) &
Position : 5
1 TIRE, 15 x 5.00-6, 2 Ply, Carlisle Snow Hog per tire assembly
Position : 5
2 BOLT, 5/16-18 x 3/4” Hex Head Cap B&S #
Position : 5
1 GRIP, Clutch, RH
Position : 6
1 SPLICE, Chute Handle
Position : 6
2 BEARING, Auger
Position : 6
1 CHUTE RING
Position : 6
1 OIL SEAL
Position : 6
1 BUSHING, Spacer, .380 ID x .750 OD x 1.030 Long
Position : 6
1 HOSE, Oil Drain
Position : 6
2 ASSY, Tire and Wheel, 15 x 5.00-6 Carlisle Sno Hog includes items 2, 4
Position : 6
1 DECAL - Danger, Auger used on Domestic Models
Position : 6
1 DECAL, CE- Auger Warning used on European Models
Position : 6
1 CLIP, Speed B&S #
Position : 6
2 GRIP, Foam, Black
Position : 7
1 SPRING PIN, .156 x 1.000
Position : 7
1 RETAINER, Bearing
Position : 7
3 RETAINER, Spout
Position : 7
1 BUSHING
Position : 7
1 WASHER, 3/8” SAE Flat or
Position : 7
3 NUT, 5/16-18 Hex Flange Lock- small
Position : 7
1 DECAL, Stripe- SNAPPER (5hp, 22”)
Position : 7
1 DECAL, Stripe- SNAPPER (8hp, 24”) not shown; similar to above decal
Position : 7
1 DECAL, Stripe- SNAPPER (7.5hp, 22”) not shown; similar to above decal
Position : 7
1 DECAL, Stripe- SNAPPER (8.5hp, 24”) not shown; similar to above decal
Position : 7
3 HAIR PIN
Position : 8
1 ROD, Chute Lower
Position : 8
1 BALL BEARING
Position : 8
6 SCREW, #10-24 x 5/8” Hex Washer Self-Tap
Position : 8
1 PIN, Drive-Loc, 3/16 x 1-1/2”
Position : 8
1 SCREW, 3/8-16 x 2” Hex Head Cap, GR 5 or
Position : 8
1 NUT, 5/16-18 Hex Flange Lock
Position : 8
1 DECAL, Danger, Chute/Deflector
Position : 8
1 DECAL, Chute Warning
Position : 8
1 ROD, Shift, Lower
Position : 9
2 SKID SHOE, Reversible- Red or
Position : 9
3 BOLT, 5/16-18 x 5/8” Square Neck Carriage, GR
Position : 9
1 COLLAR, Thrust
Position : 9
4 SCREW, 5/16-18 x 5/8” Hex Head Cap, GR
Position : 9
1 ROD, Idler
Position : 9
2 NUT, 1/4-20 2B Hex
Position : 10
1 BRACKET, Universal Gear
Position : 10
4 WASHER, 3/8” Split Lock or
Position : 10
3 NUT, 5/16-18 Hex Flange Lock
Position : 10
1 SHAFT, Rolled Worm
Position : 10
2 BALL BEARING, .669 ID x .574 OD
Position : 10
2 ROLL PIN, 3/16 x 3/4” or
Position : 10
2 ROLL PIN, 3/16 x 3/4” or
Position : 10
1 DECAL, Lube- Controls
Position : 10
3 LOCKWASHER, 1/4” Spring
Position : 11
3 WASHER, .250 (.27 ID x .62 OD)
Position : 11
12 BOLT, 1/4-20 x 1/2” Short Square Neck Carriage, GR 5 or
Position : 11
1 BOLT, 5/16-18 x 3/4” Square Neck Carriage, GR
Position : 11
1 WASHER, Thrust (.562 ID x 1.000 OD x .030/.032 Thick)
Position : 11
2 RETAINER, Bearing
Position : 11
1 WELDMENT, Intermediate Frame- Red
Position : 11
1 DECAL, Sound
Position : 11
2 BOLT, 1/4-20 x 2” Short Square Neck Carriage, GR
Position : 12
2 RETAINER, 1/4” Bolt
Position : 12
3 SCREW, 5/16-18 x 5/8 Hex Head Cap, GR 5 or
Position : 12
2 WASHER, .34 x .69 x .08 Flat
Position : 12
1 FLANGE, Bushing
Position : 12
4 LOCKWASHER, 5/16” Spring or
Position : 12
6 SPEED NUT, 1/4-20 U-Type
Position : 12
6 SPEED NUT, 1/4-20 U-Type or
Position : 12
1 DECAL, Euro Community (CE)
Position : 12
1 ROD, Upper, Shift
Position : 13
2 BOLT, 1/4-20 x 5/8” Short Square Neck Carriage
Position : 13
12 NUT, 1/4-20 Hex Flange Lock Large
Position : 13
1 NUT, 5/16-24 Hex Center Lock, GR B
Position : 13
2 OIL SEAL
Position : 13
7 NUT, 5/16-18 Hex, GR B or 5 or
Position : 13
2 BUSHING, 1.00 long
Position : 13
1 DECAL, 2005 Year of Manufacture
Position : 13
2 BLOCK, Pivot
Position : 14
2 GEAR, Universal
Position : 14
4 BOLT, 3/8-16 x 3/4” Square Neck Carriage or
Position : 14
6 NUT 1/4-20 Hex replaces
Position : 14
1 HEX SHAFT
Position : 14
1 SUPPORT, Tie Bar
Position : 14
1 WELDMENT, Shift Rod Pivot
Position : 15
1 WASHER, 3/8” Flat- Black
Position : 15
4 WASHER, 3/8” Flat or
Position : 15
1 GEAR CASE, LH- Intermediate
Position : 15
1 RING, External Retaining (for 3/4 Dia Shaft)
Position : 15
2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap
Position : 15
1 SPRING, Compression
Position : 16
1 SPRING PIN, .125 x .750
Position : 16
4 NUT, 3/8-16 Hex Nyloc
Position : 16
1 GASKET, Gear Case
Position : 16
3 SCREW, 5/16-18 x 3/4” Hex Head Cap or
Position : 16
4 JAM NUT, 3/8-16 Hex Center Lock
Position : 16
1 COTTER PIN, .125 x 1.00
Position : 17
1 WORM SHAFT
Position : 17
6 SCREW, 5/16-18 x 1” Hex Washer Self-Tap
Position : 17
2 BUSHING
Position : 17
1 DRIVEN DISC or
Position : 17
3 WASHER, 3/8” Flat or
Position : 17
4 WASHER, 3/8” SAE Flat or 7090122 or
Position : 17
2 BUSHING, .500 ID x .750 OD x .25
Position : 18
2 NUT, 1/4-20 Hex Flange Lock
Position : 18
2 CAP, Bearing, Red
Position : 18
1 SHAFT, Auger, 22”/24”
Position : 18
1 HUB, Friction Disc
Position : 18
2 ROD, Belt Guide
Position : 18
1 WASHER, 1/2” Flat (.531 ID x 1.250 OD x .08 Thick)
Position : 19
1 ROLL PIN, 1/8 x 3/4”
Position : 19
3 WASHER, 5/16” Split Lock or
Position : 19
1 GEAR, Worm
Position : 19
2 COLLAR, Thrust
Position : 19
4 NUT, 3/8-16 Hex Nyloc Heavy Thin
Position : 19
1 WELDMENT, Shift Rod
Position : 20
1 WORM
Position : 20
5 BOLT, 1/4-20 x 7/16” Short Square Neck Carriage, GR
Position : 20
1 GEAR CASE, RH- Intermediate
Position : 20
1 PIN, Slide
Position : 20
1 SUPPORT, Frame
Position : 20
1 SCREW, 1/4-20 x 2-1/4” Hex Flange Lock
Position : 21
1 WASHER, .44 x .78 x .025 Curved
Position : 21
5 NUT, 1/4-20 Hex Flange Lock
Position : 21
1 PIPE PLUG, 1/8-27 NPTF 3/4 Taper x .31 Long Hex Drive
Position : 21
2 SET SCREW, 1/4-20 x 1/2 w/Patch Lock or
Position : 21
4 SCREW, 5/16-18 x 1/2” Hex Washer Self-Tap or
Position : 21
4 SCREW, 5/16-18 x 1/2” Hex Washer Self-Tap or
Position : 21
2 WASHER, .250 (.27 ID x .62 OD)
Position : 22
1 BRACKET, Worm
Position : 22
6 SCREW, 1/4-20 x 7/8” Hex Head Cap, GR
Position : 22
1 COLLAR, Set, 1.251 ID x 2.00 OD x .50 Long
Position : 22
1 SUPPORT, Pivot
Position : 22
1 KNOB, Tapered - 3/8-16 Internal Thread- Red
Position : 23
1 NUT, 5/16-18 Hex Flange Lock
Position : 23
1 FITTING, Grease
Position : 23
1 SPROCKET #35, 12 Tooth
Position : 23
2 WASHER, 5/16” Flat
Position : 23
1 WELDMENT, Dash
Position : 24
1 SCREW, 5/16-18 x 5/8” Hex Head Cap, GR
Position : 24
1 WELDMENT, 22” Auger, RH
Position : 24
1 WASHER, 1/4 ID x 5/8 OD x .134/.109 Flat or
Position : 24
3 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 or
Position : 24
3 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 or 1922127 (HHCS, 5/16-18 x 1-
Position : 24
1 HANDLE, Lower
Position : 25
1 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
Position : 25
1 WELDMENT, 22” Auger, LH
Position : 25
1 LOCKWASHER, 1/4” Spring
Position : 25
1 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 or
Position : 25
1 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 or 1922127 (HHCS, 5/16-18 x 1-
Position : 25
2 SCREW, 5/16-18 x 2” Hex Head Cap, GR
Position : 25
2 WING KNOB, 5/16-18
Position : 26
2 COTTER PIN, 1/4” Self Locking replaces
Position : 26
1 SCREW, 1/4-20 x 3/4” Hex Head Cap, GR 5 or
Position : 26
1 COVER, Bottom- Red
Position : 26
2 WASHER, 5/16” Internal Tooth Lock
Position : 27
2 SHEAR PIN, .248 ID x 1-3/4” Long
Position : 27
1 COLLAR, Set, .756 ID x 1.249 OD x .50
Position : 27
9 SCREW, 1/4-20 x 5/8” Hex Washer Self-Tap
Position : 27
4 NUT, 5/16-18 Hex Flange Nyloc
Position : 28
4 WASHER
Position : 28
2 SET SCREW, 5/16-18 x 1/2” Square Head Cup Point or
Position : 28
1 WASHER, 7/16” Flat
Position : 28
2 WASHER, .312 (.34 ID x .75 OD) or
Position : 29
2 RING, External Retaining (for .75 dia. Shaft)
Position : 29
1 WELDMENT, Axle & Sprocket
Position : 29
1 COTTER PIN, 1/8 x 3/4”
Position : 29
1 ASSEMBLY, Rod w/Pin includes items 31, 47, 54, 55 &
Position : 30
1 KEY, #605 Woodruff
Position : 30
1 CHAIN, Roller, #35, 25.5” Long
Position : 30
1 WELDMENT, Idler Arm
Position : 30
1 WELDMENT, Idler Arm
Position : 30
1 SPRING, Compression
Position : 31
1 TUBE, Low Density Polyethylene Extruded
Position : 31
1 BUSHING
Position : 31
1 BOLT, 3/8-16 x 1-1/4” Short Square Neck Carriage
Position : 31
1 PUSH NUT
Position : 32
12 FLAT WASHER, .268 ID x .591 OD x .063 Thick
Position : 32
1 PULLEY, Traction
Position : 32
1 SPACER, .377 ID x .75 OD x .312 Long
Position : 32
1 ROD, Hold Down
Position : 33
6 WASHER, 1/4” Split Lock
Position : 33
2 NUT, 5/16-18 Large Head Center Lock or
Position : 33
1 PULLEY, Idler
Position : 33
1 SCREW, 1/4-20 x 2” Hex Head Cap, GR
Position : 34
2 SPACER, .328 ID x .562 OD x .144/.149 Thick
Position : 34
1 BELT, V Groove, 4L Section; 36.00” nom. effective length Auger Drive
Position : 34
1 BELT, V Groove, 4L Sect.; 36.00” nom. effective length Auger Drive
Position : 34
1 GRIP, Clutch, LH
Position : 35
1 ASSY, Pivot Plate/Hub w/Bearing includes weldment (1726779),
Position : 35
1 BELT, V Groove, 3L Section; 35.25” effective length Traction Drive
Position : 35
1 V-BELT, 3L, 31.64 effective length Traction Drive
Position : 35
2 NUT, 1/4-20 Hex Centerlock
Position : 36
2 SCREW, 5/16-18 x 5/8 Hex Head Cap, GR 5 or
Position : 36
1 SPRING, Extension
Position : 36
2 SPACER, Handle
Position : 37
1 WASHER
Position : 37
1 PAD, Brake
Position : 37
1 HANDLE, Upper, Left Hand
Position : 38
1 KEY, Hi-Pro, #HP-506 or
Position : 38
2 RIVET, Blind
Position : 38
2 SCREW, 1/4-20 x 1-1/2” Hex Head Cap
Position : 39
1 DRIVE DISC, w/ Spindle
Position : 39
1 ASSEMBLY, Idler Arm w/Brake Pad includes idler arm weldment
Position : 39
1 ASSEMBLY, Idler Arm w/Brake Pad incl. items 37, 38 &
Position : 39
2 SPACER, .268 ID x .394 x .165
Position : 40
1 ROD, Pivot
Position : 40
1 BOLT, 3/8-16 x 1-3/4 Short Square Neck Carriage, GR
Position : 40
2 SCREW, 1/4-20 x 3/4” Pan Head Torx Self-Tap
Position : 41
1 COTTER PIN, 1/8 x 3/4”
Position : 41
1 WASHER, 3/8” Flat (.41 ID x 1.00 OD x .13 Thick)
Position : 41
5 SCREW, 5/16-18 x 1-1/2” Hex Head Cap, GR
Position : 42
1 NUT, 5/16-18 Hex Nyloc Light or
Position : 42
1 PULLEY, Idler
Position : 42
1 LEVER, Pivot
Position : 43
2 WASHER, .312 (.34 ID x .75 OD) or
Position : 43
1 COVER, Belt
Position : 43
2 NUT, 1/4-20 Hex Nyloc
Position : 44
1 BELLCRANK
Position : 44
1 SPRING, Idler- Extension
Position : 44
1 SPRING, Extension, .562 O.D. x 4.250 Long
Position : 44
1 SNOW STICK
Position : 45
1 BUSHING
Position : 45
1 JAM NUT, 5/16-24 Hex
Position : 45
1 JAM NUT, 5/16-24 Hex or
Position : 45
1 NUT, #10-24 Hex Center Lock
Position : 46
1 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 or
Position : 46
1 KEY - Hi Pro .125 x .625 HP 504 SAE1035
Position : 46
1 ROD, Hand Control not shown; part of item
Position : 47
1 WASHER, Plain, .75 ID x 1.31.OD x .10
Position : 47
1 PULLEY, V Groove
Position : 47
1 HOLDER, Snostik- Upper
Position : 48
1 COTTER PIN, 3/8” Self Lock
Position : 48
2 SET SCREW, 5/16-18 x 5/16” Hex Recess, Cup Point
Position : 48
2 SET SCREW, 5/16-18 x 5/16” Hex Recess, Cup Point or
Position : 48
1 CLUTCH CABLE, Ground Drive- LH parts number is stamped on
Position : 49
1 PULLEY, 2.75 OD
Position : 49
4 BOLT, 5/16-18 x 2” Curved Head Square Neck GR
Position : 50
1 KEY, 3/16 Square x 1”
Position : 50
1 KEY, 3/16 Square x 1” or
Position : 50
1 WASHER, #10 Internal Tooth Lock
Position : 51
1 HARNESS CLIP
Position : 51
1 SCREW, #10-24 x 2” Hex Washer Head Machine, GR
Position : 52
1 NUT, 3/8-16 Hex Flange Lock Two Way
Position : 52
1 CORD, Electric Start
Position : 52
4 LOCKWASHER, Spring .312 or
Position : 53
1 MUFFLER GUARD, Domestic (Tecumseh)
Position : 53
1 GUARD, Muffler
Position : 53
1 BUSHING, .250 ID x .375 OD x .750 not shown; part of item
Position : 54
1 SCREW, #10-24 x 5/8” Hex Washer Self-Tap
Position : 54
1 MUFFLER, Deflector- B&S Briggs p/n
Position : 54
1 PIN, Clevis not shown; part of item
Position : 55
1 MUFFLER GUARD, Tecumseh Engine (Euro) not shown; Tecumseh p/n 127-
Position : 55
1 HEX SCREW, Thread Rolling M4 x 0.7 Briggs p/n
Position : 55
1 SPRING, Compression not shown; part of item
Position : 56
2 SCREW. Tecumseh Muffler not shown; Tecumseh p/n 42-
Position : 56
2 LOCK WASHER, Tecumseh Muffler not shown; Tecumseh p/n 36-
Position : 57
1 HEAT SHIELD, 7.5HP B&S Powerbuilt Muffler used on I75225 model
Position : 57
2 WASHER, Tecumseh Muffler not shown; Tecumseh p/n 36-
Position : 58
1 SCREW, 5/16-24 x 1” Hex Head Cap, GR
Position : 58
1 SCREW, 5/16-24 x 1-1/2” Hex Head Cap, GR
Position : 59
8 WASHER, 5/16” Flat
Position : 60
1 BUSHING, Differential Link
Position : 61
5 WASHER, 5/16” Split Lock
Position : 62
4 NUT, 5/16-18 Hex, GR 5 or B
Position : 63
2 WASHER, 5/16” Internal Tooth Lock
Position : 64