Vue éclatée autoportee snapper SNAPPER lt75175-snapper
Découvrez la vue éclatée complète autoportee snapper SNAPPER lt75175-snapper, un guide indispensable pour identifier facilement toutes les pièces détachées de votre appareil. Que vous soyez à la recherche d'une pièce en particulier ou simplement pour vous aider à la réparation, notre présentation détaillée vous aide à comprendre chaque composant de votre autoportee snapper. Optimisez la maintenance et la réparation de votre appareil grâce à des schémas précis et des références adaptées. Trouvez rapidement les pièces qu'il vous faut pour prolonger la durée de vie de votre autoportee snapper SNAPPER lt75175-snapper et éviter les pannes imprévues.
Assistant réparation
Powered by ChatGPT
Liste des pièces détachées
2 REAR TIRE ASSY, 16X6.50-8
Position : 1
1 COVER, Steering Wheel
Position : 1
1 BATTERY CABLE, Negative, 17" - Black
Position : 1
1 DECAL, Operating Instructions
Position : 1
2 NUT, 5/16-18
Position : 1
1 BAGGER COVER
Position : 1
2 FRONT TIRE ASSY, 13X5.00-6
Position : 2
1 STEERING WHEEL
Position : 2
1 MUFFLER
Position : 2
2 WINGNUT, 1/4-20
Position : 2
1 DECAL, Nose, Snapper
Position : 2
1 DECAL, Parking Brake
Position : 2
1 BOLT, 5/16-18 x 2.0
Position : 2
4 HUB CAP
Position : 3
1 DASHBOARD
Position : 3
2 * GASKET
Position : 3
1 BOOT, Battery, Positive
Position : 3
2 DECAL, Snapper 15.5 HP (15.5HP Models Only)
Position : 3
2 DECAL, Snapper 17.5 HP (17.5HP Models Only)
Position : 3
1 DECAL, Ignition Switch
Position : 3
2 E-RING, .750D x .050T
Position : 4
1 SHAFT, Shaft
Position : 4
1 BATTERY CABLE, Positive, 12" - Red
Position : 4
1 DECAL, Stripe, LH
Position : 4
1 DECAL, Cutting Height
Position : 4
4 WASHER, FLAT 1.862 x .765
Position : 5
1 BELLOWS, Steering
Position : 5
1 HEAT SHIELD ASSEMBLY
Position : 5
1 DECAL, Stripe, RH
Position : 5
1 DECAL, Roll Release
Position : 5
1 BELT GUIDE
Position : 5
4 SCREW, Self Tap
Position : 5
2 WASHER, Flat, .81 x .550
Position : 6
1 BODY, Plastic
Position : 6
1 ELECTRIC CLUTCH
Position : 6
1 DECAL, Steering Wheel Insert
Position : 6
1 DECAL, Discharge Tube
Position : 6
4 WASHER, Flat, .75-1.3
Position : 7
1 FOOTREST SLEEVE
Position : 7
1 BATTERY COVER
Position : 7
1 IDLER STUD
Position : 7
2 Bolt, Carriage 1/4-20 x .63
Position : 7
1 DECAL, Bagger Cover
Position : 7
1 DECAL, Hot Surface
Position : 7
1 SPINDLE ASSY
Position : 7
2 PIN, Cotter 1/8" x 1-1/4"
Position : 8
1 FOOTREST, Plastic
Position : 8
2 CAPSCREW, 5/16-18 x 3/4
Position : 8
2 SCREW, 1/4-14 x 3/8
Position : 8
1 DECAL, Deck Width
Position : 8
1 DECAL, Throttle Control
Position : 8
19 BOLT, Carriage 5/16-18 x 5/8
Position : 8
1 IDLER PULLEY
Position : 8
2 CAPSCREW, 3/8-16 x 1 1/4
Position : 8
1 NUT, Hex Flange Lock, 5/16-18
Position : 9
1 WIRE HARNESS
Position : 9
1 DECAL, Fire Hazard
Position : 9
13 NUT, Hex Flange, 5/16-18
Position : 9
1 BLADE, 33"
Position : 9
2 NUT, 3/8-16
Position : 9
1 BEARING, Upper Steering
Position : 10
19 CAPSCREW, 5/16-18 x 3/4
Position : 10
4 BOLT, 3/8-16 x 1-1/4
Position : 10
1 SWITCH, Limit
Position : 10
1 DECAL, Sever Hazard
Position : 10
9 NUT, Hex Flange Centerlock 5/16-18
Position : 10
1 PULLEY, 33" Input
Position : 10
2 SCREW, Flat Head 10-3/4
Position : 10
2 SPRING, Seat
Position : 11
2 SCREW, Hex Head 5/16-18 x 5/8
Position : 11
3 TIE STRAP
Position : 11
1 DECAL, Brake/Clutch
Position : 11
2 NUT, Flange, 5/16-18
Position : 11
4 BOLT, Carriage, 5/16-18 x 5/8
Position : 12
1 CAPSCREW, Hex, 7/16-20 x 2-1/2, G5
Position : 12
1 SOLENOID, 3 Pole
Position : 12
1 DECAL, Speed Control
Position : 12
2 RING, Retaining
Position : 12
1 BAG
Position : 12
4 NUT, Hex Flange, 5/16-18
Position : 13
2 STACK PULLEY
Position : 13
3 NUT, Nylock 1/4-20
Position : 13
1 DECAL, Draw Bar Load
Position : 13
1 ROD DEFLECTOR
Position : 13
1 TOLERANCE RING
Position : 13
6 SCREW, Shoulder #10-24
Position : 14
1 BAFFLE, Engine
Position : 14
1 CABLE, Battery 8GA 18" - Red
Position : 14
2 ROD, Lift Link
Position : 14
2 WASHER, Spindle
Position : 14
1 SCREW, 1/4-20 x 1.25
Position : 14
2 BOLT, Shoulder 5/16-18 x 5/8
Position : 15
2 BOLT, Carriage, 1/4 - 20 x
Position : 15
2 SCREW, Shoulder #10-24
Position : 15
1 SWITCH, Ignition
Position : 15
2 ADJUSTING NUT
Position : 15
1 NUT, Hex Flange Lock, 1/4-20
Position : 15
1 GEAR, Pinion
Position : 16
4 NUT, Hex Flange Centerlock 5/16-18
Position : 16
4 NUT, Centerlock, 1/4-20
Position : 16
2 SCREW, Torx Head 5/16-18 x 5/8
Position : 16
1 NUT, Ignition Switch
Position : 16
1 LIFT ROD, Fixed
Position : 16
1 NUT, Flange 3/8-16
Position : 16
1 GRIP
Position : 16
2 ROLLER
Position : 17
2 WASHER, Flat, 3/4
Position : 17
5 SCREW, 5/16-18 x 1/2
Position : 17
1 LOCKWASHER, Spring 7/16
Position : 17
1 CAP, Ignition Switch
Position : 17
1 SPRING, Deflector
Position : 17
1 NUT, Hex, Jam, 3/4F GR8
Position : 17
2 COTTER PIN
Position : 17
1 BEARING, Lower Steering
Position : 18
4 SCREW, 5/16-18 x 0.50
Position : 18
3 PIN, Cotter
Position : 18
4 SCREW, Thread Forming, 1/4-20 x
Position : 18
1 KEY, Ignition
Position : 18
1 PUSH CAP
Position : 18
10 BOLT, Hex 3/8-16 x 3/4
Position : 18
1 SEAT
Position : 19
1 IDLER PULLEY, Backside
Position : 19
2 SWITCH, Seat
Position : 19
1 REAR DISCHARGE CHUTE
Position : 19
4 NUT, Hex Flange, 3/8-16
Position : 19
2 BOLT, Carriage, 3/8-16 x 5/8
Position : 19
2 BOLT, Shoulder, .31-18 x 1 1/4
Position : 20
4 BOLT, Shoulder, 5/16-18 x 1.50
Position : 20
1 NUT, Adjusting
Position : 20
1 SWITCH, PTO
Position : 20
1 CHUTE EXTENSION, Upper
Position : 20
6 NUT, Centerlock, 3/8-16
Position : 20
2 WASHER, 0.406 x 1 1/4
Position : 20
2 NUT, Hex Flange Centerlock 5/16-18
Position : 21
1 IDLER PULLEY, Fixed
Position : 21
1 NUT, Flange, 5/16-18
Position : 21
1 BUZZER, Bag Full Indicator
Position : 21
1 RUBBER STRAP
Position : 21
1 BELT, 33" Blade Drive
Position : 21
2 NUT, 5/16-18
Position : 21
1 WASHER, Flat, 1-1.3 16G
Position : 22
8 CAPSCREW, 5/16-18 x 3/4
Position : 22
1 * TRANSMISSION, Hydro Gear
Position : 22
1 SWITCH, BAG FULL
Position : 22
1 PIN
Position : 22
1 BAFFLE, Rubber
Position : 22
2 WASHER, .328 x 1.062 x .062 Z
Position : 23
6 SCREW, Hex 1/4-20 x 5/8
Position : 23
1 BAGGER SWITCH
Position : 23
1 BOLT, Carriage 1/4-20 x 5/8
Position : 23
2 NUT, Hex Jam, 1/2-20
Position : 23
1 SWITCH, Bag Full
Position : 23
2 BOLT, Hex Head, 5/16-24 x 2-3/4, G5
Position : 24
2 BOLT, Carriage 5/16-18 x 5/8
Position : 24
2 PIN, Threaded Shoulder, 3/8-16 x 1-1/2
Position : 24
2 WASHER, Flat, 5/16
Position : 24
1 FUSE, 15 Amp
Position : 24
2 WASHER, 1/2" Internal Tooth Lock
Position : 24
1 PIN
Position : 24
2 NUT, Centerlock 3/8-16
Position : 25
2 CLAMP, Hose, Yellow
Position : 25
2 NUT, Hex Flange 3/8-16
Position : 25
1 NUT, Hex Flange Lock, 1/4-20
Position : 25
1 HARNESS, Buzzer Connector
Position : 25
3 BOLT, Carriage, 5/16-18 x 3/4
Position : 25
1 NUT, Hex Center Lock Jam, 5/8-18
Position : 25
3 BOLT, Carriage, 1/4-20 x 5/8
Position : 25
2 NUT, 5/16-24
Position : 26
1 FUEL LINE
Position : 26
1 WASHER, 1.75 x 1.04 x 0.15
Position : 26
1 SERVICE KIT, Buzzer and Harness (Includes Ref Nos. 21 and 25)
Position : 26
1 WASHER, Flat, 5/16 x
Position : 26
2 NUT, Hex, 1/4-20
Position : 26
2 WASHER, Flat, .39-1. 14G
Position : 27
1 FUEL CAP
Position : 27
1 PEDAL, Clutch and Brake
Position : 27
4 BOLT, Shoulder, 3/8-16 x 1.10
Position : 27
6 SCREW, Oval Head, 5/16 - 24 x 21/32
Position : 27
13 CAPSCREW, 5/16-18 x 3/4
Position : 28
1 TANK, Fuel 1.6 Gallon.
Position : 28
1 ROD, Parking Brake
Position : 28
3 SCREW, 1/4-20 x 1/2
Position : 28
4 NUT, Hex Flange, 3/8-16
Position : 28
6 WASHER, 5/16" Internal Tooth Lock
Position : 28
1 E-RING, Retainer
Position : 29
1 KNOB, Parking Brake
Position : 29
1 MULCH COVER
Position : 29
6 NUT, Hex, 5/16 -
Position : 29
1 WASHER, .26 X.75 X 16GA
Position : 29
2 BUMPER, Rubber
Position : 30
2 BOLT, Carriage, 1/4-20 x 0.63
Position : 30
2 KEY, Square
Position : 30
4 SCREW, 10-24 x 1/2
Position : 30
6 WASHER, 1/2 x 7/8
Position : 30
1 NUT, Hex Flange 5/16-18
Position : 30
1 WINGNUT
Position : 30
1 SCREW, Thread Forming, 1/4-20 x
Position : 31
2 NUT, Keps Lock 1/4-20
Position : 31
1 NUT, Adjusting
Position : 31
1 HEAT SHIELD
Position : 31
2 WASHER, 1/2 x 1-1/2
Position : 31
1 HOLDER, Blade
Position : 31
2 SCREW, Self Tapping, 5/16-18 x 1.13
Position : 31
1 WASHER, Flat, .34, 1.20 11G
Position : 32
2 WASHER, Flat, .81 X .550 X 16GA
Position : 32
1 BOLT, Hex, 5/16-18 x 2-1/2
Position : 32
1 SCREEN, Spark Arrester, Flat
Position : 32
6 HAIRPIN
Position : 32
2 CAPSCREW, Hex Head, 1/2-20 x 1-1/4, GR5
Position : 32
1 WASHER, Flat 1.862 x .765 x 16GA
Position : 32
1 SCREW, Thread Forming, 10-16 x
Position : 33
1 RING, Foam
Position : 33
4 BOLT, Hex-Head 5/16-18 x
Position : 33
1 SCREEN, Spark Arrester, Formed
Position : 33
3 WHEELS, Anti Scalp
Position : 33
1 HAIRPIN
Position : 33
2 BOLT, Hex 3/8-16 x 1-1/2 G5
Position : 34
4 NUT, Flange Lock 1/4-20
Position : 34
3 CAPSCREW, Hex Head, 3/8-24 x 3/4, GR5
Position : 34
1 WASHER, 25/32 x 1.5 x .132
Position : 34
1 THROTTLE CONTROL
Position : 35
1 GRIP, Seat Adjustment Lever
Position : 35
3 NUT, Flange Lock, 3/8-16
Position : 35
3 SPACER, 3" Long
Position : 35
1 SPRING, Extension PTO
Position : 35
2 WASHER, .39-1.14
Position : 35
2 SCREW, Self Tap, #8 x 3/8
Position : 36
1 HEAT SHIELD (Used with Service Kit 885280 or After Serial No. 2013421413)
Position : 36
3 NUT, Hex Nyloc, 3/8-24
Position : 36
4 BOLT, Carriage, 3/8-16 x 5/8
Position : 36
1 LATCH, Spring
Position : 36
1 TINNERMAN CLIP
Position : 37
5 TAPE, Reflective
Position : 37
3 WASHER, Flat 3/8
Position : 37
1 DEFLECTOR, Chute
Position : 37
2 CAPSCREW, Hex Whiz Lock Flange, 5/16-18 x 3/4
Position : 37
1 FLOORMAT, RH
Position : 38
2 WASHER, .391 x 0.62 x.03
Position : 38
1 FLOORMAT, LH
Position : 39
4 WASHER, 0.641 x 1.38
Position : 39
1 BOLT, 1/4-20 x
Position : 39
3 PIN, Cotter, 3/4
Position : 40
1 NUT, Keps Lock 1/4-20
Position : 40
2 SCREW, 1/4 - 20 x 5/8
Position : 40
1 RETAINER, Spring
Position : 41
5 HAIR PIN, .56D-.092T
Position : 41
2 SCREW, Thread Forming, 10-24
Position : 42
1 BELT, Drive, 33"
Position : 42
3 CAPSCREW, Hex Whiz Lock, 5/16-18 x 3/4
Position : 42
2 CAPSCREW, Hex Head, 3/8-16 x 1-1/4
Position : 42
1 SPRING, Extension
Position : 43
2 NUT, 3/8-16
Position : 43
1 Spring, Brake Extension
Position : 44
4 NUT, Hex Flange Serrated, 5/16-18
Position : 45
2 BOLT, Carriage 1/4-20 x 5/8
Position : 46
1 PAD, Hydro Pedal
Position : 47
1 ROD, Shift Link
Position : 48
1 LEVER, Lift Deck
Position : 49
1 GRIP, .50 Black
Position : 50
1 PIN, Front Hanger
Position : 51
4 NUT, Hex Flange 5/16-18
Position : 52
1 ROD, Roll Release
Position : 53
1 ROD, Battery
Position : 54
1 ROD, Clutch Hydro
Position : 55
1 SCREW, Self Tap 5/16-18 x 7/8
Position : 56
1 SPRING, Extension
Position : 57
2 SPACER
Position : 58
6 WASHER, Flat, 1-1/4
Position : 59
1 PEDAL PAD, Hydro Reverse
Position : 60
1 SERVICE KIT, Lifter Assembly (Not Illustrated, Includes Ref. Nos. 8 and 49)
Position : 61
1 CAPSCREW, Hex, 1/4-20 x 9/16
Position : 63