Vue éclatée tondeuse snapper SNAPPER snb7-2006-snapper
Découvrez la vue éclatée complète tondeuse snapper SNAPPER snb7-2006-snapper, un guide indispensable pour identifier facilement toutes les pièces détachées de votre appareil. Que vous soyez à la recherche d'une pièce en particulier ou simplement pour vous aider à la réparation, notre présentation détaillée vous aide à comprendre chaque composant de votre tondeuse snapper. Optimisez la maintenance et la réparation de votre appareil grâce à des schémas précis et des références adaptées. Trouvez rapidement les pièces qu'il vous faut pour prolonger la durée de vie de votre tondeuse snapper SNAPPER snb7-2006-snapper et éviter les pannes imprévues.
Assistant réparation
Powered by ChatGPT
Liste des pièces détachées
1 HANDLE, Upper
Position : 1
1 WELDMENT, Deck, 21” Non-Adjust Air finish: red painted but w/o decals
Position : 1
1 WELDMENT, Deck, 21”, S.P., HV, Core Model finish: red painted but w/o decals
Position : 1
2 WHEEL, 8 x 1.75” Plastic
Position : 1
1 BELT, Poly-V
Position : 1
4 NUT, 5/16-18 Hex Lock or
Position : 1
1 ASSEMBLY, Bag Adapter/Cover (Includes items 2 thru 9)
Position : 1
1 BAG ASSEMBLY (Door) includes items 2, 3 &
Position : 1
1 DECAL, Easy Speed, Control Panel
Position : 1
1 SCREEN, Fastener Assembly
Position : 1
2 LATCH, Frame Attachment
Position : 1
1 HANDLE, Middle
Position : 2
5 NUT, 5/16-18 Hex Flange Lock, GR
Position : 2
1 BOLT, 5/16-18 x 3/4” Hex Washer Face Shoulder per wheel arm assembly
Position : 2
4 NUT, 7/16-20 Hex Center Lock Jam
Position : 2
1 WASHER, 44 x .78 x .025 Curved
Position : 2
1 WASHER, Cone
Position : 2
1 ADAPTER, Grass Bag Euro 21” see Grass Bag Accessory page
Position : 2
1 GRASS BAG (Door w/Gray Letters)
Position : 2
1 DECAL, SNAPPER, Steel Decks
Position : 2
1 RING, Bottom (21.77” Inside Diameter)
Position : 2
1 HANDLE, Lower LH (Adjustable)
Position : 3
3 BOLT, 5/16-18 x 1/2”, Short Neck Carriage, GR
Position : 3
1 LATCH, Height per wheel arm assembly
Position : 3
2 BUSHING, Axle
Position : 3
1 LINK, Differential
Position : 3
1 PULLEY, Poly-V Belt (3.5” O.D.)
Position : 3
1 COVER, Bag Adapter
Position : 3
1 CONNECTOR, Grass Bag (weldment)
Position : 3
1 DECAL, 2006 Year of Mfg.
Position : 3
1 BLADE, 21” Quad Edge Ninja
Position : 3
3 NUT, 5/16-24 Hex, GR5 only 1 shown
Position : 3
2 ROD, Tine
Position : 3
1 HANDLE, Lower RH (Adjustable)
Position : 4
2 PLUG, Hole, Polyethylene
Position : 4
1 GRIP, Height Latch per wheel arm assembly
Position : 4
1 WASHER, 5/16” Internal Tooth Lock
Position : 4
2 WASHER, 44 x .78 x .025 Curved
Position : 4
1 HINGE, Chute Cover
Position : 4
1 ASSEMBLY, Bag Wire (12” Wide)
Position : 4
1 DECAL,Euro Community (CE)
Position : 4
3 WASHER, 5/16” Split Lock only 1 shown
Position : 4
1 SUPPORT, Wheel
Position : 4
1 BAIL, OPC Control
Position : 5
1 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR 5 or
Position : 5
4 PLUG, Wheel
Position : 5
1 SCREW, 5/16-18 x 1/2” Pan Head Self-Tap (Torx)
Position : 5
1 ASSEMBLY, Right Housing (Incl. items 6, 7, 8, 9, 10 & 30)
Position : 5
5 BOLT, 1/4-20 x 1/2” Short Neck Carriage, GR
Position : 5
1 PLUG, Chute Adapter
Position : 5
1 DECAL, Warning (Deck)
Position : 5
3 SPRING only 1 shown
Position : 5
1 TRAY, Tine
Position : 5
1 CLIP, Zone Control
Position : 6
1 RETAINER, 5/16” Bolt
Position : 6
4 RETAINER, 5/16” Bolt
Position : 6
2 WHEEL, 10 x 1.75” Plastic
Position : 6
1 ASSEMBLY, Idler Arm, Bushing & Spacer
Position : 6
1 HOUSING, Right Side
Position : 6
2 WASHER, 1/4” Internal Tooth Lock
Position : 6
1 ADAPTER, Grass Bag Euro 21”
Position : 6
1 DECAL, Spart Plug International Symbol
Position : 6
6 KIT, Tine Thatching Spring was
Position : 6
1 CABLE, Zone Control (52-63/64” Long)
Position : 7
1 SCREW, 3/8-24 x 2” Hex Head Cap, GR
Position : 7
4 NUT, 5/16-18 Hex Flange Lock, GR 5 or
Position : 7
1 ARM, Clutch Idler
Position : 7
3 SCREW, 5/16-24 x 1-1/8” Rib Neck, GR
Position : 7
2 NUT, 1/4-20 Hex or
Position : 7
2 DECAL, Warning (Euro)
Position : 7
1 BUSHING, Wheel Adjuster
Position : 7
1 HANDLE, Clutch
Position : 8
2 WASHER, Cone
Position : 8
1 AXLE, 21”
Position : 8
4 BUSHING, Flange, .381 x .625 x .62
Position : 8
1 SEAL, 5/8” Internal Diameter
Position : 8
1 STOP, Cover
Position : 8
2 RETAINER, 5/16” Bolt
Position : 8
1 DECAL, Caution, Symbols
Position : 8
1 AXLE, Wheel
Position : 8
1 GRIP, International Symbol
Position : 9
1 BLADE, 21” Air Lift
Position : 9
1 BEARING, 9/16” I.D. per Rear Wheel Arm
Position : 9
1 SPACER, Idler Arm
Position : 9
1 BEARING, Tapered- (Differential Housing)
Position : 9
1 TRIM, Moulding
Position : 9
1 DECAL, Noise, 98 dB
Position : 9
1 WHEEL, 7.00 x 1.50 Gage
Position : 9
1 CABLE, Clutch Control (41-1/4” Long)
Position : 10
1 BLADE, 21” Ninja (Quad Edge) used on ERP2167519BV &
Position : 10
3 SCREW, #10-32 x 3/8” Hex washer Self-Tap per Rear Wheel Arm
Position : 10
1 NUT, 1/4-28 Hex Top Lock
Position : 10
1 BALL BEARING, 7/16 I.D., 1/1/8” O.D. was
Position : 10
2 BOLT, 5/16-18 x 1-1/8” Short Neck Carriage, GR
Position : 10
2 NUT, 5/16-18 Hex Large Flange Center Lock
Position : 10
1 DECAL, Speed Shift
Position : 10
10 NUT, 1/4-20 Hex Top Lock was 7090761 (only 9 shown)
Position : 10
1 COVER, Vinyl
Position : 11
1 COVER, Belt
Position : 11
1 LATCH, Height Adjusting (long) per Rear Wheel Arm
Position : 11
1 PULLEY, Idler, V21
Position : 11
1 PLUG, Transmission Housing
Position : 11
1 SPACER, .316 I.D. x .375 O.D. x .310 thick
Position : 11
1 DECAL, Throttle Control, B&S
Position : 11
4 WASHER, 1/4” Flat was
Position : 11
1 SPRING, Clutch- 21S
Position : 12
1 PULLEY, Engine (25mm I. D. x 2-1/8” O.D.)
Position : 12
1 BOLT, 5/16-18 x 1” Hex Washer Face Shoulder per wheel arm assembly
Position : 12
1 SCREW, 1/4-28 x 1-3/8” Hex Head Cap, GR
Position : 12
1 GEAR, Input
Position : 12
3 NUT, 5/16-18 Hex Large Flange Center Lock
Position : 12
2 DECAL, Deck/Chute International Warning
Position : 12
2 SPRING, Compression
Position : 12
1 BRACKET, Shift
Position : 13
1 SCREW, 5/16-18 x 1/2” Hex Socket Head
Position : 13
1 ASSY, Wheel Arm, Right Rear (S.P.) Incl. 4, 6, 9, 10, 11, 15 &
Position : 13
1 COTTER PIN, 3/32 x 1/2”
Position : 13
1 AXLE, Short
Position : 13
3 RETAINER, 5/16” Bolt
Position : 13
1 DECAL, OPC Bail (International Symbol)
Position : 13
2 BOLT, 1/4-20 x 1-1/4” Hex, GR
Position : 13
2 TIE, Wire, 1.29 long, black
Position : 14
1 KEY, Woodruff #HP-506 Hi-Pro Used on EP217019BV &
Position : 14
1 ASSY, Wheel Arm Left Rear Long SP21S Incl. 4, 6, 9, 10, 11, 16 &
Position : 14
1 SPRING, Clutch- 21S See also HANDLES &
Position : 14
1 GEAR, Differential (46 Tooth)
Position : 14
1 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR 5 or
Position : 14
1 DECAL, Ninja, Mulching System
Position : 14
2 NUT, 1/4-20 Hex, GR 5 was
Position : 14
1 BRACKET, Bell Crank
Position : 15
1 HUB, Blade Drive 25mm I.D.
Position : 15
1 ARM, Wheel, Right Rear
Position : 15
1 SPRING, Idler- Torsion
Position : 15
2 PLATE, 46T Gear
Position : 15
1 SIDE CHUTE, 21”
Position : 15
1 DECAL, Hi Vac, Cutting Deck
Position : 15
2 CAP, Vinyl
Position : 15
1 SPACER, .33 x .63 x .156
Position : 16
3 SCREW, 3/8-16 x 1” Self-Tapping engine mount bolts
Position : 16
1 ARM, Wheel, Left Rear
Position : 16
1 STUD, Idler (3/8-24 thread)
Position : 16
2 WASHER, Thrust, 3/4” I.D.
Position : 16
1 COVER, 21” Deck
Position : 16
2 BOLT, 1/4-20 x 2-1/2” Square Neck Carriage only 1 shown
Position : 16
1 BELL CRANK
Position : 17
4 SCREW, 5/16-24 x 21/32” Oval Head Machine
Position : 17
1 HOLDER, Bearing (Inner Half)
Position : 17
4 SCREW, #10-32 x 1-1/2” Hex Head Cap GR
Position : 17
6 BOLT, 5/16-18 x 1” Square Neck Carriage, GR 5 was 7090383 (only 1 shown)
Position : 17
1 CONTROL PANEL (w/o Electrical Switch Hole)
Position : 18
2 AIR LIFT
Position : 18
3 WASHER, 3/8” Internal Tooth Lock
Position : 18
1 GASKET, Housing
Position : 18
2 BOLT, 1/4-20 x 3/4” Square Neck Carriage, GR 5 was
Position : 18
4 SCREW, 1/4-20 x 1/2” Pan Head Self-Tap (Torx)
Position : 19
4 WASHER, 5/16” Internal Tooth Lock
Position : 19
2 NUT, 3/8-24 Hex
Position : 19
3 WASHER, 5/16” Internal/External Tooth Lock
Position : 19
6 WASHER, Reinforcing only 1 shown
Position : 19
2 WASHER, .33 x .88 x .09 Flat
Position : 20
4 NUT, 5/16-24 Hex, GR
Position : 20
1 WASHER, .390 I.D. Flat
Position : 20
1 BRACKET, Differential
Position : 20
6 WASHER, 5/16” Split Lock only 1 shown
Position : 20
1 SCREW, 5/16-18 x 7/8” Hex Head Cap, GR
Position : 21
1 FENDER (Weldment), EP21S
Position : 21
1 BALL BEARING, Spherical O.D., .38 I.D.
Position : 21
4 SCREW, 1/4-20 x 1” Hex washer Self-Tap or
Position : 21
6 NUT, 5/16-18 Hex, GR 5 was 7090196 (only 1 shown)
Position : 21
1 TEENUT 5/16-18
Position : 22
6 SCREW, 1/4-20 x 1/2” Hex Flange Self-Tap
Position : 22
1 O-RING, V21
Position : 22
1 SPACER, Axle Gear
Position : 22
2 NUT, 1/2” Push
Position : 22
1 BUSHING, Differential, .328 x .625 x .41
Position : 23
1 DECAL, Caution Symbols (International)
Position : 23
1 HOLDER, Bearing (Outer Half)
Position : 23
1 ASSEMBLY, Long Axle
Position : 23
4 BEARING, Nyliner
Position : 23
2 BOLT, 5/16-18 x 3/4” Hex Flange Lock GR
Position : 24
1 BOLT, 5/16-18 x 2-1/4” Hex Flange Lock
Position : 24
2 SCREW, 1/4-20 x 1/2” Hex Flange Self-Tap or
Position : 24
4 GEAR, Pinion (12 tooth)
Position : 24
1 SCREW, 5/16-18 x 1/4” Set
Position : 24
2 NUT, 5/16-18 Hex Flange Lock, GR 5 or
Position : 25
1 BUSHING, .388 x .625 x 1.62 Flanged matl: powdered metal
Position : 25
1 NUT, 3/8-24 Hex Center Lock, GR
Position : 25
4 SPACER, Pinion Gear
Position : 25
2 WASHER, 1/2” Flat
Position : 25
1 NUT, 5/16-18 Hex Center Lock
Position : 26
2 WASHER, 7/16” Flat
Position : 26
1 GUIDE, Thrust Plate (3/8-24 thread)
Position : 26
4 SHAFT, Pinion
Position : 26
1 DECAL, Adjustment
Position : 26
1 LEVER, Shift
Position : 27
1 COVER, Belt- IP21S
Position : 27
1 THRUST PLATE, Short
Position : 27
4 NUT, #10-32 Hex Nyloc
Position : 27
1 DECAL, Thatcherizer
Position : 27
1 NUT, 5/16-24 Hex Center Lock GR
Position : 28
1 SCREW, 5/16-18 x 1/2” Hex Head Cap, GR
Position : 28
1 WASHER, 3/8” Flat
Position : 28
1 ASSY, Left Housing (Phantom)
Position : 28
1 CLIP, Wiring Harness
Position : 29
1 WASHER, 5/16” Flat
Position : 29
1 SHIELD- Hex Shaft
Position : 29
1 HOUSING, Left
Position : 29
4 SCREW, 5/16-18 x 1-7/8” Curved Head GR 2 or
Position : 30
2 RETAINING RING, .625 External
Position : 30
3 GASKET, 5/8” O. D.
Position : 30
4 KNOB, 5/16-18 Wing (Black)
Position : 31
1 COTTER PIN, .06 x .50 YZ or
Position : 31
2 SCREW, 1/4-20 x 1-1/2 Hex Head Cap GR
Position : 32
2 WASHER, .28 x .63 x .06 Flat
Position : 32
5 WASHER, 1/4” Internal Tooth Lock
Position : 33
1 LINK, Transfer (1/4-28 thread)
Position : 33
3 NUT, 1/4-20 Hex or
Position : 34
2 NUT, 1/4-28 Hex See also HANDLES &
Position : 34
1 SCREW, 1/4-20 x 2” Hex Head Cap, GR
Position : 35
1 BALL JOINT, 1/4-28 See also HANDLES &
Position : 35
2 BUSHING, .27 x .35 x .4 Flange
Position : 36
1 WASHER, 1/4” Internal Tooth Lock
Position : 36
1 PIN, 1/4 x 1-1/2”
Position : 37
1 DISC, Driven (Cantilever)
Position : 37
1 PUSH-NUT, 1/4”
Position : 38
1 BALL BEARING- 3/4” Bore
Position : 38
2 BALL JOINT, 1/4-28
Position : 39
1 SHAFT, Hex Drive
Position : 39
4 NUT, 1/4-28 Hex
Position : 40
1 PULLEY, Poly-V (2” O.D.)
Position : 40
1 FOAM GRIP, 18.75” long
Position : 41
1 BELT, Engine Drive (Stretch)
Position : 41
1 SCREW, 3/8-16 x 2” Hex Head Cap, GR
Position : 42
1 ASSEMBLY, Steel Drive Disc 7053263, Drive Disc & Bushing
Position : 42
1 NUT, 3/8-16 Hex Center Lock
Position : 43
1 BUSHING, Powdered Metal
Position : 43
4 WASHER, 5/16” Internal Tooth Lock
Position : 44
1 RETAINER, 5/16” Bolt
Position : 44
8 WASHER, 7/16” Flat
Position : 45
1 SPACER, .500 x .65 x 1.75
Position : 45
2 WASHER, Nylon
Position : 46
1 BRACKET, Deck, P21S
Position : 46
1 ROD, Speed Control (1/4-28 thread)
Position : 47
1 SPRING, Wheel Drive
Position : 47
1 GUIDE, Rope (1/4-20 thread)
Position : 48
1 BOLT, 5/16-18 x 1/2”, Short Neck Carriage, GR
Position : 48
1 NUT, 1/4-28 Hex GR 5 or B
Position : 49
1 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR 5 or
Position : 49
1 CABLE-TIE, 7”
Position : 50
2 NUT, 5/16-18 Hex Flange Lock, GR 5 or
Position : 50
1 *THROTTLE CONTROL, .48 x .61
Position : 51
1 NUT, 3/8-16 Hex, GR 5 or B
Position : 51
1 THROTTLE KNOB
Position : 52
1 KNOB, Shift
Position : 53
1 CLAMP, 7/8” Double Cable
Position : 54
1 SCREW, #8-32 x 1/2” Cross Recess Filister Head Machine
Position : 55
1 NUT, #8-32 Hex
Position : 56
1 SCREW, 5/16-18 x 1-1/4” Hex Washer Head Self-Tap
Position : 57
1 WASHER, Belleville
Position : 58
1 SCREW, 5/16-24 x 1” Hex Head Cap GR
Position : 59
1 WASHER, 11/32” Flat
Position : 60
1 COTTER PIN, 5/16 Self Lock
Position : 61
1 DECAL, Easy Speed, Control Panel
Position : 62
1 CLAMP, Casing
Position : 63
1 SCREW,#10-32 x 5/8” Self-Tap
Position : 64
1 *ASSY, Driven Disc (Cantilever) Euro
Position : 7042934
1 ASSEMBLY, Clutch Idler (incl. items 6, 10, 11 & 12)
Position : 7051913
1 ASSEMBLY, Deck Bracket (Incl. items 8, 45 & 46)
Position : 7052987
1 ASSEMBLY, Transmission (Incl. items 1 thru 30)
Position : 7059070
KIT, Snapperizer “HV” (Incl. items 1 & 2 thru 5) used on EP217019BV
Position : 7060440
32oz. *”00” Grease not shown
Position : 7061017
KIT, Recycling Cover (Incl. items 1 & 3 below) for 4HP & above engines
Position : 7061200
KIT, Recycling Plug (Incl. items 2 & 3 below) for 4HP & above engines
Position : 7061201
KIT, Thatcherizer (Incl. items 1 thru 27)
Position : 7061256
KIT, Snapperizer “F & M” (Incl. items 1& 2A thru 5) used on ERP2167519BV &
Position : 7063041
1 THROTTLE CONTROL, .48 x .61 (conduit length: 48-1/2”)
Position : 7074460