Explosionszeichnung commande de vélo électrique HOMELITE Homelite 410
Entdecken Sie die vollständige Explosionszeichnung commande de vélo électrique HOMELITE Homelite 410 – ein unverzichtbarer Leitfaden zur Identifizierung aller Ersatzteile. Unsere Darstellung hilft Ihnen, jede Komponente Ihres commande de vélo électrique zu verstehen. Finden Sie schnell die benötigten Teile für Ihr commande de vélo électrique HOMELITE Homelite 410.
Reparatur-Assistent
Powered by ChatGPT
Ersatzteilliste
3 SCREW- Pan hd. (8-32 x 3/8")
Position: 1
1 COVER- Clutch
Position: 2
1 GROMMET (Hi-Lo)
Position: 2
1 SHIELD- Sawdust
Position: 2
1 SPIDER- Clutch
Position: 3
1 GASKET- Carburetor
Position: 3
1 RIVET- Pan hd.
Position: 3
1 STUD- Shoulder
Position: 4
1 NUT- Hex (1/4-20)
Position: 4
1 SCREW- Hex Sems (10-24 x 17/8")
Position: 5
1 PIN- Guide bar adj.
Position: 5
1 WASHER- Thrust
Position: 6
1 SCREW- Guide bar adj.
Position: 6
1 BUSHING
Position: 7
2 NUT-(3/8-16)
Position: 8
1 BEARING- Needle
Position: 9
1 LABEL- Warning
Position: 9
1 PLATE- Guide bar (outer) 410 only
Position: 9
1 PLATE- Guide bar (inner)
Position: 10
1 WASHER- Thrust
Position: 11
1 SCREW- Hex Sems hd. (10-24 x 1/2")
Position: 11
3 SCREW- Fil. hd. (10-24 x 7/8")
Position: 12
1 CLAMP- Wire
Position: 12
1 WORM- Oil pump
Position: 13
1 PANEL- Rear
Position: 13
1 GROMMET
Position: 13
1 SPRING- Clip
Position: 14
2 SCREW- (4-40 x 1/4")
Position: 15
1 BUTTON
Position: 15
4 SCREW- Threaded rolling plastite (#10 x 5/8")
Position: 16
1 GASKET
Position: 17
1 SEAL- Felt
Position: 18
1 RING- Retaining
Position: 18
1 SUPPORT- Filter cover
Position: 19
1 LABEL- Ansi
Position: 19
1 GASKET
Position: 20
1 SCREW- (#10 x 5/8")
Position: 20
1 CLAMP
Position: 21
2 SCREW- Plastite (6 x 3/8")
Position: 21
1 TUBING 5" (manual delivery)
Position: 22
2 SCREW- (10-24 x 1 1/4")
Position: 22
1 TUBING- 6 3/4" (auto oil pick-up)
Position: 23
1 RETAINER- Choke
Position: 23
1 COVER- Cylinder (410 only)
Position: 23
1 ROD- Choke
Position: 24
1 GASKET
Position: 25
1 BOOT- Throttle rod
Position: 25
1 RING- Retaining
Position: 26
2 RING- Retaining
Position: 27
2 GASKET FILTER & SUPPORT
Position: 27
1 BUSHING
Position: 27
2 PISTON- Ring
Position: 28
2 WASHER- Flat
Position: 28
1 NEEDLE- Bearing (after lot #E286)
Position: 29
4 SCREW- Hex Sems (10-24 x 5/8")
Position: 29
1 PIN- Dowel
Position: 30
2 GASKET- Fuel & Oil Cap
Position: 30
4 REED
Position: 31
2 BEAD- Chain
Position: 31
1 CONNECTOR- Carburetor
Position: 32
2 RETAINER- Filler cap
Position: 32
1 WASHER- Retaining
Position: 32
1 RETAINER- Reed valve
Position: 33
6 PIN- Isolator
Position: 33
4 SCREW- Washer hd. (8-32 x 5/8")
Position: 34
1 BODY- Muffler
Position: 34
1 STIFFNER- Connector (for units prior to Lot #C300)
Position: 35
1 PLATE- Stiffner
Position: 35
1 SEAT- Reed valve
Position: 36
3 SPACER- Muffler
Position: 36
4 WASHER- Conical
Position: 38
1 SCREW- Hex Sems (10-32 x 3/8")
Position: 38
4 SCREW- Soc hd. (10-24 x 1 1/8")
Position: 39
3 SCREW- Soc hd. (8-32 x 1/2")
Position: 39
1 ADAPTER- Carburetor
Position: 40
1 SCREEN- Spark
Position: 40
1 TUBING- 4 3/4"
Position: 42
1 TUBING- 6 3/4" (auto pick up)
Position: 42
3 SCREW- Hex hd. (12-24 x 17/8")
Position: 42
4 NUT- Centerlock (10-24)
Position: 43
1 TUBING- 4 3/4" (pulse line)
Position: 43
1 TUBING- 8 3/4" (fuel line pick up)
Position: 44
4 SCREW- Pan hd. (6-32 x 3/8")
Position: 45
1 TUBING- 5" (Man. delivery)
Position: 45
1 NUT- Lock (3/8-24)
Position: 46
2 VALVE- Check
Position: 46
2 FILTER- 11/32"
Position: 47
1 SCROLL- Air guide
Position: 48
1 TUBING- 9 3/4" (man pick up)
Position: 48
1 GROMMET
Position: 49
2 PIN- Trigger
Position: 49
1 SPRING- Compression
Position: 50
2 SCREW- Hex Sems (10-24 x 7/8")
Position: 51
1 PIN- Throttle lock
Position: 51
1 CLAMP- Wire
Position: 52
1 SCREW- Set (6-32 x 1/4")
Position: 53
1 SPRING- Flat
Position: 55
2 WASHER- Flat
Position: 56
1 LOCK- Trigger
Position: 56
2 SPRING- Starter pawl
Position: 57
1 ROTOR
Position: 58
1 SCREW- Hex hd. (10-24 x 5/8")
Position: 58
1 WASHER- Lock
Position: 59
5 SCREW- (10-24 x 1 3/4")
Position: 60
1 FITTING
Position: 62
2 BEARING- Ball
Position: 63
2 BOLT- Guide bar
Position: 64
2 FITTING
Position: 65
1 KEY- Woodruff
Position: 66
2 SCREW- Hex Sems (8-32 x 1/2")
Position: 68
1 STOP- Chain
Position: 69
2 SCREW- (10-24 x 1/2")
Position: 71
2 NUT
Position: 72
2 WASHER- Sealing
Position: 73
2 PIN- Dowel
Position: 74
1 LEAD- High tension
Position: 75
STUD- Hex hd.
Position: 17108
TOOL KIT- Carburetor repair
Position: 17789
PAINT- Rod
Position: 23475
TOOL- Needle bearing (plug)
Position: 23756
SHIM- Air gap (black)
Position: 24306
SILASTIC
Position: 24823
SCREW- Hex hd.
Position: 80627
1 SCREW
Position: 82335
GROMMET
Position: 93357
1 BEARING- Needle (prior to lot #E286) (See index #29)
Position: 93369
RING- Retaining
Position: 93972
1 BEARING- Ball (see index #63)
Position: 94621
CLIP- Spring
Position: 96200
1 BEARING- Needle (long) (see index #29) (after lot #E286)
Position: 97566
SPACER- Long bearing tool
Position: 97790
SPACER- Short bearing tool
Position: 97791
ANVIL- Bearing Installation
Position: 238464
BIT- Driver torx (isolator pin) 1/4 shank
Position: 2498201
BIT- Driver torx (isolator pin) 5/16 shank
Position: 2498202
TUBING- Rubber 10' (fuel & oil)
Position: 9311299
TUBING- Rubber 10' (pulse line)
Position: 9315799