Exploderad vy commande de vélo électrique HOMELITE Homelite 410
Upptäck den fullständiga exploderade vyn commande de vélo électrique HOMELITE Homelite 410 – en oumbärlig guide för att identifiera reservdelar. Vår presentation hjälper dig förstå varje komponent i din commande de vélo électrique. Hitta snabbt delarna till din commande de vélo électrique HOMELITE Homelite 410.
Reparationsassistent
Powered by ChatGPT
Lista över reservdelar
3 SCREW- Pan hd. (8-32 x 3/8")
Position: 1
1 COVER- Clutch
Position: 2
1 GROMMET (Hi-Lo)
Position: 2
1 SHIELD- Sawdust
Position: 2
1 SPIDER- Clutch
Position: 3
1 GASKET- Carburetor
Position: 3
1 RIVET- Pan hd.
Position: 3
1 STUD- Shoulder
Position: 4
1 NUT- Hex (1/4-20)
Position: 4
1 SCREW- Hex Sems (10-24 x 17/8")
Position: 5
1 PIN- Guide bar adj.
Position: 5
1 WASHER- Thrust
Position: 6
1 SCREW- Guide bar adj.
Position: 6
1 BUSHING
Position: 7
2 NUT-(3/8-16)
Position: 8
1 BEARING- Needle
Position: 9
1 LABEL- Warning
Position: 9
1 PLATE- Guide bar (outer) 410 only
Position: 9
1 PLATE- Guide bar (inner)
Position: 10
1 WASHER- Thrust
Position: 11
1 SCREW- Hex Sems hd. (10-24 x 1/2")
Position: 11
3 SCREW- Fil. hd. (10-24 x 7/8")
Position: 12
1 CLAMP- Wire
Position: 12
1 WORM- Oil pump
Position: 13
1 PANEL- Rear
Position: 13
1 GROMMET
Position: 13
1 SPRING- Clip
Position: 14
2 SCREW- (4-40 x 1/4")
Position: 15
1 BUTTON
Position: 15
4 SCREW- Threaded rolling plastite (#10 x 5/8")
Position: 16
1 GASKET
Position: 17
1 SEAL- Felt
Position: 18
1 RING- Retaining
Position: 18
1 SUPPORT- Filter cover
Position: 19
1 LABEL- Ansi
Position: 19
1 GASKET
Position: 20
1 SCREW- (#10 x 5/8")
Position: 20
1 CLAMP
Position: 21
2 SCREW- Plastite (6 x 3/8")
Position: 21
1 TUBING 5" (manual delivery)
Position: 22
2 SCREW- (10-24 x 1 1/4")
Position: 22
1 TUBING- 6 3/4" (auto oil pick-up)
Position: 23
1 RETAINER- Choke
Position: 23
1 COVER- Cylinder (410 only)
Position: 23
1 ROD- Choke
Position: 24
1 GASKET
Position: 25
1 BOOT- Throttle rod
Position: 25
1 RING- Retaining
Position: 26
2 RING- Retaining
Position: 27
2 GASKET FILTER & SUPPORT
Position: 27
1 BUSHING
Position: 27
2 PISTON- Ring
Position: 28
2 WASHER- Flat
Position: 28
1 NEEDLE- Bearing (after lot #E286)
Position: 29
4 SCREW- Hex Sems (10-24 x 5/8")
Position: 29
1 PIN- Dowel
Position: 30
2 GASKET- Fuel & Oil Cap
Position: 30
4 REED
Position: 31
2 BEAD- Chain
Position: 31
1 CONNECTOR- Carburetor
Position: 32
2 RETAINER- Filler cap
Position: 32
1 WASHER- Retaining
Position: 32
1 RETAINER- Reed valve
Position: 33
6 PIN- Isolator
Position: 33
4 SCREW- Washer hd. (8-32 x 5/8")
Position: 34
1 BODY- Muffler
Position: 34
1 STIFFNER- Connector (for units prior to Lot #C300)
Position: 35
1 PLATE- Stiffner
Position: 35
1 SEAT- Reed valve
Position: 36
3 SPACER- Muffler
Position: 36
4 WASHER- Conical
Position: 38
1 SCREW- Hex Sems (10-32 x 3/8")
Position: 38
4 SCREW- Soc hd. (10-24 x 1 1/8")
Position: 39
3 SCREW- Soc hd. (8-32 x 1/2")
Position: 39
1 ADAPTER- Carburetor
Position: 40
1 SCREEN- Spark
Position: 40
1 TUBING- 4 3/4"
Position: 42
1 TUBING- 6 3/4" (auto pick up)
Position: 42
3 SCREW- Hex hd. (12-24 x 17/8")
Position: 42
4 NUT- Centerlock (10-24)
Position: 43
1 TUBING- 4 3/4" (pulse line)
Position: 43
1 TUBING- 8 3/4" (fuel line pick up)
Position: 44
4 SCREW- Pan hd. (6-32 x 3/8")
Position: 45
1 TUBING- 5" (Man. delivery)
Position: 45
1 NUT- Lock (3/8-24)
Position: 46
2 VALVE- Check
Position: 46
2 FILTER- 11/32"
Position: 47
1 SCROLL- Air guide
Position: 48
1 TUBING- 9 3/4" (man pick up)
Position: 48
1 GROMMET
Position: 49
2 PIN- Trigger
Position: 49
1 SPRING- Compression
Position: 50
2 SCREW- Hex Sems (10-24 x 7/8")
Position: 51
1 PIN- Throttle lock
Position: 51
1 CLAMP- Wire
Position: 52
1 SCREW- Set (6-32 x 1/4")
Position: 53
1 SPRING- Flat
Position: 55
2 WASHER- Flat
Position: 56
1 LOCK- Trigger
Position: 56
2 SPRING- Starter pawl
Position: 57
1 ROTOR
Position: 58
1 SCREW- Hex hd. (10-24 x 5/8")
Position: 58
1 WASHER- Lock
Position: 59
5 SCREW- (10-24 x 1 3/4")
Position: 60
1 FITTING
Position: 62
2 BEARING- Ball
Position: 63
2 BOLT- Guide bar
Position: 64
2 FITTING
Position: 65
1 KEY- Woodruff
Position: 66
2 SCREW- Hex Sems (8-32 x 1/2")
Position: 68
1 STOP- Chain
Position: 69
2 SCREW- (10-24 x 1/2")
Position: 71
2 NUT
Position: 72
2 WASHER- Sealing
Position: 73
2 PIN- Dowel
Position: 74
1 LEAD- High tension
Position: 75
STUD- Hex hd.
Position: 17108
TOOL KIT- Carburetor repair
Position: 17789
PAINT- Rod
Position: 23475
TOOL- Needle bearing (plug)
Position: 23756
SHIM- Air gap (black)
Position: 24306
SILASTIC
Position: 24823
SCREW- Hex hd.
Position: 80627
1 SCREW
Position: 82335
GROMMET
Position: 93357
1 BEARING- Needle (prior to lot #E286) (See index #29)
Position: 93369
RING- Retaining
Position: 93972
1 BEARING- Ball (see index #63)
Position: 94621
CLIP- Spring
Position: 96200
1 BEARING- Needle (long) (see index #29) (after lot #E286)
Position: 97566
SPACER- Long bearing tool
Position: 97790
SPACER- Short bearing tool
Position: 97791
ANVIL- Bearing Installation
Position: 238464
BIT- Driver torx (isolator pin) 1/4 shank
Position: 2498201
BIT- Driver torx (isolator pin) 5/16 shank
Position: 2498202
TUBING- Rubber 10' (fuel & oil)
Position: 9311299
TUBING- Rubber 10' (pulse line)
Position: 9315799