Exploded view lt 75155 SNAPPER lt75155
Discover the complete exploded view lt 75155 SNAPPER lt75155, an essential guide to easily identify all spare parts of your appliance. Whether you are looking for a specific part or need help with the repair, our detailed presentation helps you understand each component of your lt 75155. Quickly find the parts you need to extend the life of your lt 75155 SNAPPER lt75155 and avoid unexpected breakdowns.
Repair Assistant
Powered by ChatGPT
Spare Parts List
2 REAR TIRE ASSY, 16/650
Position: 1
1 COVER, Steering Wheel
Position: 1
1 BATTERY CABLE, Negative
Position: 1
1 DECAL, Operating Instructions
Position: 1
2 NUT, 5/16-18
Position: 1
1 BAGGER COVER
Position: 1
2 FRONT TIRE ASSY, 13/500
Position: 2
1 STEERING WHEEL
Position: 2
1 MUFFLER
Position: 2
1 MUFFLER
Position: 2
2 WINGNUT, 1/4-20
Position: 2
1 DECAL, Nose
Position: 2
1 DECAL, Parking Brake
Position: 2
1 BOLT, 5/16-18 x 2.0
Position: 2
4 HUB CAP
Position: 3
1 DASHBOARD
Position: 3
2 *GASKET
Position: 3
1 BOOT, Battery, Positive
Position: 3
2 DECAL, Snapper 15.5 HP 15.5HP MODELS ONLY
Position: 3
2 DECAL, Snapper 17.5 HP 17.5HP MODELS ONLY
Position: 3
1 DECAL, Ignition Switch
Position: 3
2 E-RING, .750D x .050T
Position: 4
1 SHAFT, Shaft
Position: 4
1 ADAPTOR, Muffler
Position: 4
1 ADAPTOR, Muffler
Position: 4
1 BATTERY CABLE, Positive
Position: 4
1 DECAL, Stripe, LH
Position: 4
1 DECAL, Cutting Height
Position: 4
4 WASHER, FLAT 1.862 x .765 x 16GA
Position: 5
1 BELLOWS, Steering
Position: 5
1 FOOTREST, Plastic
Position: 5
1 HEAT SHIELD ASSEMBLY
Position: 5
1 HEAT SHIELD ASSEMBLY
Position: 5
1 DECAL, Stripe, RH
Position: 5
1 DECAL, Roll Release
Position: 5
1 BELT GUIDE
Position: 5
4 SCREW, Self Tap
Position: 5
2 WASHER, Flat, .81 x .550 x 16GA
Position: 6
1 BODY, Plastic
Position: 6
1 ELECTRIC CLUTCH
Position: 6
1 DECAL, Steering Wheel Insert
Position: 6
1 DECAL, Discharge Tube
Position: 6
4 WASHER, Flat, .75-1.3-.07FLT
Position: 7
1 FOOTREST SLEEVE
Position: 7
1 BATTERY COVER
Position: 7
1 IDLER STUD
Position: 7
2 Bolt, Carriage 1/4-20 x .63
Position: 7
1 DECAL, Bagger Cover
Position: 7
1 DECAL, Hot Surface
Position: 7
2 PIN, Cotter 1/8" x 1-1/4"
Position: 8
1 FOOTREST, Plastic
Position: 8
2 CAPSCREW, 5/16-18 x 3/4
Position: 8
2 SCREW, 1/4-14 x 3/8
Position: 8
1 DECAL, Deck Width
Position: 8
1 DECAL, Throttle Control
Position: 8
19 BOLT, Carriage 5/16-18 x 5/8
Position: 8
1 IDLER PULLEY
Position: 8
2 BOLT, Shoulder, 3/8-16 x 1.00
Position: 8
2 CAPSCREW, 3/8-16 x 1 1/4
Position: 8
1 NUT, 5/16-18 Hex Flange Lock
Position: 9
2 BOLT, Shoulder, 5/16-18 x 4.35
Position: 9
1 WIRE HARNESS
Position: 9
1 DECAL, Fire Hazard
Position: 9
13 NUT, Hex Flange, 5/16-18
Position: 9
1 BLADE, 33"
Position: 9
2 NUT, 3/8-16
Position: 9
1 BEARING, Upper Steering
Position: 10
18 CAPSCREW, 5/16-18 x 3/4
Position: 10
4 BOLT, 3/8-16 x 1-1/4
Position: 10
1 SWITCH, Limit
Position: 10
1 DECAL, Sever Hazard
Position: 10
9 NUT, Hex Flange Centerlock 5/16-18
Position: 10
1 PULLEY, 33" Input
Position: 10
2 SCREW, Flat Head 10-3/4
Position: 10
2 SPRING, Seat
Position: 11
2 SCREW, Hex Head 5/16-18 x 5/8
Position: 11
3 TIE STRAP
Position: 11
2 KNOB
Position: 11
2 NUT, Flange, 5/16-18
Position: 11
4 BOLT, Carriage, 5/16-18 x 5/8
Position: 12
1 CAPSCREW, Hex, 7/16-20 x 2-1/2
Position: 12
1 SOLENOID, 3 Pole
Position: 12
1 DECAL, Speed Control
Position: 12
2 RING, Retaining
Position: 12
1 BAG
Position: 12
4 NUT, Hex Flange, 5/16-18
Position: 13
1 STACK PULLEY
Position: 13
2 STACK PULLEY
Position: 13
3 NUT, Nylock 1/4-20
Position: 13
1 DECAL, Draw Bar Load
Position: 13
1 ROD DEFLECTOR
Position: 13
1 TOLERANCE RING
Position: 13
1 HANDLE, Bagger
Position: 13
6 SCREW, Shoulder #10-24
Position: 14
1 BAFFLE, Engine
Position: 14
1 CABLE, Battery 8GA 18.00L - Red
Position: 14
1 DECAL, Noise Level
Position: 14
2 ROD, Lift Link
Position: 14
2 WASHER, Spindle
Position: 14
1 SCREW, 1/4-20 x 1.25
Position: 14
2 BOLT, Shoulder 5/16-18 x 5/8
Position: 15
2 BOLT, Carriage, 1/4 - 20 x
Position: 15
2 SCREW, Shoulder #10-24
Position: 15
1 SWITCH, Ignition
Position: 15
2 ADJUSTING NUT
Position: 15
1 GEAR, Pinion
Position: 16
4 NUT, Hex Flange Centerlock 5/16-18
Position: 16
4 NUT, 1/4 - 20 Centerlock
Position: 16
2 SCREW, Torx Head 5/16-18 x 5/8
Position: 16
1 NUT, Ignition Switch
Position: 16
1 LIFT ROD, Fixed
Position: 16
1 NUT, Flange 3/8-16
Position: 16
1 GRIP
Position: 16
2 ROLLER
Position: 17
2 WASHER, Flat, 3/4
Position: 17
5 SCREW, 5/16-18 x 0.50
Position: 17
1 LOCKWASHER, Spring 7/16
Position: 17
1 CAP, Ignition Switch
Position: 17
1 SPRING, Deflector
Position: 17
1 NUT, Hex, Jam, 3/4F GR8
Position: 17
2 COTTER PIN
Position: 17
1 BEARING, Lower Steering
Position: 18
4 SCREW, 5/16-18 x 0.50
Position: 18
3 PIN, COTTER
Position: 18
1 SCREW, Hex 1/4-20 x 5/8
Position: 18
4 SCREW, Thread Forming, 1/4-20 x
Position: 18
1 KEYS, With Plasic Cover
Position: 18
1 PUSH CAP
Position: 18
10 BOLT, Hex 3/8-16 x 0.75
Position: 18
1 SEAT
Position: 19
1 IDLER PULLEY, Backside
Position: 19
1 LOCK, SCREW
Position: 19
2 SWITCH, Seat
Position: 19
1 REAR DISCHARGE CHUTE
Position: 19
4 NUT, Hex Flange, 3/8-16
Position: 19
2 BOLT, Carriage, 3/8-16 x 5/8
Position: 19
2 BOLT, Shoulder, .31-18 x 1 1/4
Position: 20
4 BOLT, Shoulder, 5/16-18 x 1.50
Position: 20
1 NUT, Adjusting
Position: 20
1 SWITCH, PTO
Position: 20
1 CHUTE EXTENSION, Upper
Position: 20
6 NUT, Centerlock, 3/8-16
Position: 20
2 WASHER, 0.406 x 1 1/4
Position: 20
2 NUT, Hex Flange Centerlock 5/16-18
Position: 21
1 IDLER PULLEY, Fixed
Position: 21
1 NUT, Flange, 5/16-18
Position: 21
1 BUZZER, Bag Full Indicator (BEFORE SERIAL NO. 2013421412)
Position: 21
1 BUZZER, Bag Full Indicator (AFTER SERIAL NO. 2013421413)
Position: 21
1 RUBBER STRAP
Position: 21
1 BELT, 33" Blade Drive
Position: 21
1 WASHER, 1-1.3 16G FLT
Position: 22
8 CAPSCREW, 5/16-18 x 3/4
Position: 22
1 TRANSMISSION, Hydro Gear
Position: 22
1 SWITCH, BAG FULL
Position: 22
1 PIN
Position: 22
2 BOLT, 1/2-20 x 1.25
Position: 22
1 BAFFLE, Rubber
Position: 22
2 WASHER, .328 x 1.062 x .062 Z
Position: 23
6 SCREW, Hex 1/4-20 x 5/8
Position: 23
1 GUIDE, Belt Short
Position: 23
1 BAGGER SWITCH
Position: 23
1 BOLT, Carriage 1/4-20 x 0.63
Position: 23
2 NUT, Hex Jam, 1/2-20
Position: 23
1 SWITCH, Bag Full
Position: 23
2 BOLT, Hex Head, 5/16-24 x 2-3/4
Position: 24
2 BOLT, Carriage 5/16-18 x 5/8
Position: 24
2 PIN, Threaded Shoulder, 3/8-16 x 1-1/2
Position: 24
2 WASHER, Flat, 5/16
Position: 24
1 FUSE, 15 Amp
Position: 24
1 NUT, Hex Flange Lock, 1/4-20
Position: 24
2 WASHER, 1/2" Internal Tooth Lock
Position: 24
1 PIN
Position: 24
2 NUT, Centerlock 3/8-16
Position: 25
2 CLAMP, Hose, Yellow
Position: 25
2 NUT, Hex Flange 3/8-16
Position: 25
1 NUT, Hex Flange Lock, 1/4-20
Position: 25
1 HARNESS, Buzzer Connector (AFTER SERIAL NO. 2013421413)
Position: 25
3 BOLT, Carriage, 5/16-18 x 3/4
Position: 25
1 NUT, 5/8-18 Hex Center Lock Jam
Position: 25
3 BOLT, Carriage, .25-20 x 0.63
Position: 25
2 NUT, 5/16-24
Position: 26
1 FUEL LINE
Position: 26
1 WASHER, 1.75 x 1.04 x 0.15
Position: 26
1 SERVICE KIT, Buzzer and Harness (Includes Ref Nos. 21 and 25)
Position: 26
2 NUT, Hex, 1/4-20
Position: 26
2 WASHER, .39-1. 14G FLT
Position: 27
1 FUEL CAP
Position: 27
1 PEDAL, Clutch and Brake
Position: 27
1 BRACKET, Muffler Support
Position: 27
4 BOLT, Shoulder, 3/8-16 x 1.10
Position: 27
6 SCREW, Oval Head, 5/16 - 24 x 21/32
Position: 27
13 CAPSCREW, 5/16-18 x 3/4
Position: 28
1 TANK, Fuel 1.6 Gallon.
Position: 28
1 ROD, Parking Brake
Position: 28
3 SCREW, .1/4-20 x .50
Position: 28
4 NUT, Hex Flange, 3/8-16
Position: 28
6 WASHER, 5/16" Internal Tooth Lock
Position: 28
1 E-RING, Retainer
Position: 29
1 KNOB, Parking Brake
Position: 29
1 DEFLECTOR, Muffler
Position: 29
1 MULCH COVER
Position: 29
6 NUT, Hex, 5/16 -
Position: 29
1 WASHER, .26 X.75 X 16GA
Position: 29
2 BUMPER, Rubber
Position: 30
2 BOLT, Carriage, 1/4-20 x 0.63
Position: 30
2 KEY, Square
Position: 30
4 SCREW, 10-24 x 1/2
Position: 30
6 WASHER, .51-.87
Position: 30
1 NUT, Hex Flange 5/16-18
Position: 30
1 WINGNUT
Position: 30
1 SCREW, Thread Forming, 1/4-20 x
Position: 31
2 NUT, Keps Lock 1/4-20
Position: 31
1 NUT, Adjusting
Position: 31
1 HEAT SHIELD
Position: 31
2 WASHER, .51-1.5
Position: 31
2 SCREW, Self Tapping, 5/16-18 x 1.13
Position: 31
1 WASHER, Flat, .34, 1.20 11G
Position: 32
2 WASHER, Flat, .81 X .550 X 16GA
Position: 32
1 BOLT, Hex, 5/16-18 x 2-1/2
Position: 32
6 HAIRPIN
Position: 32
2 SCREW, 1/2-20 x 1-1/4" Hex Head Cap, GR5
Position: 32
1 WASHER, Flat 1.862 x .765 x 16GA
Position: 32
1 WASHER,Flat 1.862 x .765 x 16GA
Position: 32
1 SCREW, Thread Formning, 10-16 x
Position: 33
1 RING, Foam
Position: 33
4 BOLT, Hex-Head 5/16-18 x
Position: 33
3 WHEELS, Anti Scalp
Position: 33
2 NUT, 1/2-20 Hex
Position: 33
1 HAIRPIN
Position: 33
2 BOLT, Hex 3/8-16 x 1-1/2
Position: 34
4 NUT, Flange Lock 1/4-20
Position: 34
4 NUT, Hex Flange Lock, 5/16-18
Position: 34
3 SCREW, 3/8-24 x 3/4" Hex Head Cap, GR5
Position: 34
1 WASHER 25/32 x 1.5 x .132
Position: 34
1 THROTTLE CONTROL
Position: 35
1 GRIP, Seat Adjustment Lever
Position: 35
3 NUT, Flange Lock, 3/8-16
Position: 35
3 SPACER, 3" Long
Position: 35
1 SPRING, Extension PTO
Position: 35
2 WASHER, .39-1.14
Position: 35
2 SCREW, Self Tap, #8 x 3/8
Position: 36
1 HEAT SHIELD (Used with Service Kit 885280 or After Serial No. 2013421413)
Position: 36
2 WASHER, Flat, 3/4
Position: 36
3 NUT, Hex Nyloc, 3/8-24
Position: 36
4 BOLT, Carriage, 3/8-16 x 5/8
Position: 36
1 LATCH, Spring
Position: 36
1 TINNERMAN CLIP
Position: 37
3 WASHER, Flat 3/8
Position: 37
2 CAPSCREW, 5/16-18 x 3/4
Position: 37
1 FLOORMAT, RH
Position: 38
2 WASHER, Flat, 5/16
Position: 38
2 WASHER, .391 x 0.62 x.03
Position: 38
1 FLOORMAT, LH
Position: 39
4 WASHER, 0.641 x 1.38
Position: 39
1 BOLT, 1/4-20 x 1.0
Position: 39
1 HANDLE, Bagger
Position: 39
3 PIN, Cotter, 3/4
Position: 40
1 NUT, Keps Lock 1/4-20
Position: 40
2 SCREW, 1/4 - 20 x 5/8
Position: 40
1 RETAINER, Spring
Position: 41
5 HAIR PIN, .56D-.092T
Position: 41
1 BRACE
Position: 41
2 SCREW, Thread Forming, 10-24
Position: 42
1 BELT, Drive, 33"
Position: 42
2 CAPSCREW, Hex Hd., 3/8-16 x 1-1/4
Position: 42
1 SPRING, Extension
Position: 43
2 NUT, 3/8-16
Position: 43
1 Spring, Brake Extension
Position: 44
2 BOLT, Carriage 1/4-20 x 0.63
Position: 46
1 PAD, Hydro Pedal
Position: 47
1 ROD, Shift Link
Position: 48
1 LEVER, Lift Deck
Position: 49
1 GRIP, .50 Black
Position: 50
1 PIN, Front Hanger
Position: 51
4 NUT, Hex Flange 5/16-18
Position: 52
1 ROD, Roll Release
Position: 53
1 ROD, Battery
Position: 54
1 ROD, Clutch Hydro
Position: 55
1 SCREW, Self Tap 5/16-18 x 7/8
Position: 56
1 SPRING, Extension
Position: 57
2 SPACHER
Position: 58
6 WASHER, Flat, 1-1/4
Position: 59
1 PEDAL PAD, Hydro Reverse (BEFORE SERIAL NO. 2013421412)
Position: 60
1 PEDAL PAD, Hydro Reverse (AFTER SERIAL NO. 2013421413)
Position: 60
1 SERVICE KIT, Lifter Assembly (Not Illustrated, Includes Ref. Nos. 8 and 49)
Position: 61
LT75RD-CE
Position: 7800352
LT75RD-CE, FR
Position: 7800353
LT75RD-CE
Position: 7800356
LT75RD-CE, FR
Position: 7800357