Exploderad vy lt 75155 SNAPPER lt75155
Upptäck den fullständiga exploderade vyn lt 75155 SNAPPER lt75155 – en oumbärlig guide för att identifiera reservdelar. Vår presentation hjälper dig förstå varje komponent i din lt 75155. Hitta snabbt delarna till din lt 75155 SNAPPER lt75155.
Reparationsassistent
Powered by ChatGPT
Lista över reservdelar
2 REAR TIRE ASSY, 16/650
Position: 1
1 COVER, Steering Wheel
Position: 1
1 BATTERY CABLE, Negative
Position: 1
1 DECAL, Operating Instructions
Position: 1
2 NUT, 5/16-18
Position: 1
1 BAGGER COVER
Position: 1
2 FRONT TIRE ASSY, 13/500
Position: 2
1 STEERING WHEEL
Position: 2
1 MUFFLER
Position: 2
1 MUFFLER
Position: 2
2 WINGNUT, 1/4-20
Position: 2
1 DECAL, Nose
Position: 2
1 DECAL, Parking Brake
Position: 2
1 BOLT, 5/16-18 x 2.0
Position: 2
4 HUB CAP
Position: 3
1 DASHBOARD
Position: 3
2 *GASKET
Position: 3
1 BOOT, Battery, Positive
Position: 3
2 DECAL, Snapper 15.5 HP 15.5HP MODELS ONLY
Position: 3
2 DECAL, Snapper 17.5 HP 17.5HP MODELS ONLY
Position: 3
1 DECAL, Ignition Switch
Position: 3
2 E-RING, .750D x .050T
Position: 4
1 SHAFT, Shaft
Position: 4
1 ADAPTOR, Muffler
Position: 4
1 ADAPTOR, Muffler
Position: 4
1 BATTERY CABLE, Positive
Position: 4
1 DECAL, Stripe, LH
Position: 4
1 DECAL, Cutting Height
Position: 4
4 WASHER, FLAT 1.862 x .765 x 16GA
Position: 5
1 BELLOWS, Steering
Position: 5
1 FOOTREST, Plastic
Position: 5
1 HEAT SHIELD ASSEMBLY
Position: 5
1 HEAT SHIELD ASSEMBLY
Position: 5
1 DECAL, Stripe, RH
Position: 5
1 DECAL, Roll Release
Position: 5
1 BELT GUIDE
Position: 5
4 SCREW, Self Tap
Position: 5
2 WASHER, Flat, .81 x .550 x 16GA
Position: 6
1 BODY, Plastic
Position: 6
1 ELECTRIC CLUTCH
Position: 6
1 DECAL, Steering Wheel Insert
Position: 6
1 DECAL, Discharge Tube
Position: 6
4 WASHER, Flat, .75-1.3-.07FLT
Position: 7
1 FOOTREST SLEEVE
Position: 7
1 BATTERY COVER
Position: 7
1 IDLER STUD
Position: 7
2 Bolt, Carriage 1/4-20 x .63
Position: 7
1 DECAL, Bagger Cover
Position: 7
1 DECAL, Hot Surface
Position: 7
2 PIN, Cotter 1/8" x 1-1/4"
Position: 8
1 FOOTREST, Plastic
Position: 8
2 CAPSCREW, 5/16-18 x 3/4
Position: 8
2 SCREW, 1/4-14 x 3/8
Position: 8
1 DECAL, Deck Width
Position: 8
1 DECAL, Throttle Control
Position: 8
19 BOLT, Carriage 5/16-18 x 5/8
Position: 8
1 IDLER PULLEY
Position: 8
2 BOLT, Shoulder, 3/8-16 x 1.00
Position: 8
2 CAPSCREW, 3/8-16 x 1 1/4
Position: 8
1 NUT, 5/16-18 Hex Flange Lock
Position: 9
2 BOLT, Shoulder, 5/16-18 x 4.35
Position: 9
1 WIRE HARNESS
Position: 9
1 DECAL, Fire Hazard
Position: 9
13 NUT, Hex Flange, 5/16-18
Position: 9
1 BLADE, 33"
Position: 9
2 NUT, 3/8-16
Position: 9
1 BEARING, Upper Steering
Position: 10
18 CAPSCREW, 5/16-18 x 3/4
Position: 10
4 BOLT, 3/8-16 x 1-1/4
Position: 10
1 SWITCH, Limit
Position: 10
1 DECAL, Sever Hazard
Position: 10
9 NUT, Hex Flange Centerlock 5/16-18
Position: 10
1 PULLEY, 33" Input
Position: 10
2 SCREW, Flat Head 10-3/4
Position: 10
2 SPRING, Seat
Position: 11
2 SCREW, Hex Head 5/16-18 x 5/8
Position: 11
3 TIE STRAP
Position: 11
2 KNOB
Position: 11
2 NUT, Flange, 5/16-18
Position: 11
4 BOLT, Carriage, 5/16-18 x 5/8
Position: 12
1 CAPSCREW, Hex, 7/16-20 x 2-1/2
Position: 12
1 SOLENOID, 3 Pole
Position: 12
1 DECAL, Speed Control
Position: 12
2 RING, Retaining
Position: 12
1 BAG
Position: 12
4 NUT, Hex Flange, 5/16-18
Position: 13
1 STACK PULLEY
Position: 13
2 STACK PULLEY
Position: 13
3 NUT, Nylock 1/4-20
Position: 13
1 DECAL, Draw Bar Load
Position: 13
1 ROD DEFLECTOR
Position: 13
1 TOLERANCE RING
Position: 13
1 HANDLE, Bagger
Position: 13
6 SCREW, Shoulder #10-24
Position: 14
1 BAFFLE, Engine
Position: 14
1 CABLE, Battery 8GA 18.00L - Red
Position: 14
1 DECAL, Noise Level
Position: 14
2 ROD, Lift Link
Position: 14
2 WASHER, Spindle
Position: 14
1 SCREW, 1/4-20 x 1.25
Position: 14
2 BOLT, Shoulder 5/16-18 x 5/8
Position: 15
2 BOLT, Carriage, 1/4 - 20 x
Position: 15
2 SCREW, Shoulder #10-24
Position: 15
1 SWITCH, Ignition
Position: 15
2 ADJUSTING NUT
Position: 15
1 GEAR, Pinion
Position: 16
4 NUT, Hex Flange Centerlock 5/16-18
Position: 16
4 NUT, 1/4 - 20 Centerlock
Position: 16
2 SCREW, Torx Head 5/16-18 x 5/8
Position: 16
1 NUT, Ignition Switch
Position: 16
1 LIFT ROD, Fixed
Position: 16
1 NUT, Flange 3/8-16
Position: 16
1 GRIP
Position: 16
2 ROLLER
Position: 17
2 WASHER, Flat, 3/4
Position: 17
5 SCREW, 5/16-18 x 0.50
Position: 17
1 LOCKWASHER, Spring 7/16
Position: 17
1 CAP, Ignition Switch
Position: 17
1 SPRING, Deflector
Position: 17
1 NUT, Hex, Jam, 3/4F GR8
Position: 17
2 COTTER PIN
Position: 17
1 BEARING, Lower Steering
Position: 18
4 SCREW, 5/16-18 x 0.50
Position: 18
3 PIN, COTTER
Position: 18
1 SCREW, Hex 1/4-20 x 5/8
Position: 18
4 SCREW, Thread Forming, 1/4-20 x
Position: 18
1 KEYS, With Plasic Cover
Position: 18
1 PUSH CAP
Position: 18
10 BOLT, Hex 3/8-16 x 0.75
Position: 18
1 SEAT
Position: 19
1 IDLER PULLEY, Backside
Position: 19
1 LOCK, SCREW
Position: 19
2 SWITCH, Seat
Position: 19
1 REAR DISCHARGE CHUTE
Position: 19
4 NUT, Hex Flange, 3/8-16
Position: 19
2 BOLT, Carriage, 3/8-16 x 5/8
Position: 19
2 BOLT, Shoulder, .31-18 x 1 1/4
Position: 20
4 BOLT, Shoulder, 5/16-18 x 1.50
Position: 20
1 NUT, Adjusting
Position: 20
1 SWITCH, PTO
Position: 20
1 CHUTE EXTENSION, Upper
Position: 20
6 NUT, Centerlock, 3/8-16
Position: 20
2 WASHER, 0.406 x 1 1/4
Position: 20
2 NUT, Hex Flange Centerlock 5/16-18
Position: 21
1 IDLER PULLEY, Fixed
Position: 21
1 NUT, Flange, 5/16-18
Position: 21
1 BUZZER, Bag Full Indicator (BEFORE SERIAL NO. 2013421412)
Position: 21
1 BUZZER, Bag Full Indicator (AFTER SERIAL NO. 2013421413)
Position: 21
1 RUBBER STRAP
Position: 21
1 BELT, 33" Blade Drive
Position: 21
1 WASHER, 1-1.3 16G FLT
Position: 22
8 CAPSCREW, 5/16-18 x 3/4
Position: 22
1 TRANSMISSION, Hydro Gear
Position: 22
1 SWITCH, BAG FULL
Position: 22
1 PIN
Position: 22
2 BOLT, 1/2-20 x 1.25
Position: 22
1 BAFFLE, Rubber
Position: 22
2 WASHER, .328 x 1.062 x .062 Z
Position: 23
6 SCREW, Hex 1/4-20 x 5/8
Position: 23
1 GUIDE, Belt Short
Position: 23
1 BAGGER SWITCH
Position: 23
1 BOLT, Carriage 1/4-20 x 0.63
Position: 23
2 NUT, Hex Jam, 1/2-20
Position: 23
1 SWITCH, Bag Full
Position: 23
2 BOLT, Hex Head, 5/16-24 x 2-3/4
Position: 24
2 BOLT, Carriage 5/16-18 x 5/8
Position: 24
2 PIN, Threaded Shoulder, 3/8-16 x 1-1/2
Position: 24
2 WASHER, Flat, 5/16
Position: 24
1 FUSE, 15 Amp
Position: 24
1 NUT, Hex Flange Lock, 1/4-20
Position: 24
2 WASHER, 1/2" Internal Tooth Lock
Position: 24
1 PIN
Position: 24
2 NUT, Centerlock 3/8-16
Position: 25
2 CLAMP, Hose, Yellow
Position: 25
2 NUT, Hex Flange 3/8-16
Position: 25
1 NUT, Hex Flange Lock, 1/4-20
Position: 25
1 HARNESS, Buzzer Connector (AFTER SERIAL NO. 2013421413)
Position: 25
3 BOLT, Carriage, 5/16-18 x 3/4
Position: 25
1 NUT, 5/8-18 Hex Center Lock Jam
Position: 25
3 BOLT, Carriage, .25-20 x 0.63
Position: 25
2 NUT, 5/16-24
Position: 26
1 FUEL LINE
Position: 26
1 WASHER, 1.75 x 1.04 x 0.15
Position: 26
1 SERVICE KIT, Buzzer and Harness (Includes Ref Nos. 21 and 25)
Position: 26
2 NUT, Hex, 1/4-20
Position: 26
2 WASHER, .39-1. 14G FLT
Position: 27
1 FUEL CAP
Position: 27
1 PEDAL, Clutch and Brake
Position: 27
1 BRACKET, Muffler Support
Position: 27
4 BOLT, Shoulder, 3/8-16 x 1.10
Position: 27
6 SCREW, Oval Head, 5/16 - 24 x 21/32
Position: 27
13 CAPSCREW, 5/16-18 x 3/4
Position: 28
1 TANK, Fuel 1.6 Gallon.
Position: 28
1 ROD, Parking Brake
Position: 28
3 SCREW, .1/4-20 x .50
Position: 28
4 NUT, Hex Flange, 3/8-16
Position: 28
6 WASHER, 5/16" Internal Tooth Lock
Position: 28
1 E-RING, Retainer
Position: 29
1 KNOB, Parking Brake
Position: 29
1 DEFLECTOR, Muffler
Position: 29
1 MULCH COVER
Position: 29
6 NUT, Hex, 5/16 -
Position: 29
1 WASHER, .26 X.75 X 16GA
Position: 29
2 BUMPER, Rubber
Position: 30
2 BOLT, Carriage, 1/4-20 x 0.63
Position: 30
2 KEY, Square
Position: 30
4 SCREW, 10-24 x 1/2
Position: 30
6 WASHER, .51-.87
Position: 30
1 NUT, Hex Flange 5/16-18
Position: 30
1 WINGNUT
Position: 30
1 SCREW, Thread Forming, 1/4-20 x
Position: 31
2 NUT, Keps Lock 1/4-20
Position: 31
1 NUT, Adjusting
Position: 31
1 HEAT SHIELD
Position: 31
2 WASHER, .51-1.5
Position: 31
2 SCREW, Self Tapping, 5/16-18 x 1.13
Position: 31
1 WASHER, Flat, .34, 1.20 11G
Position: 32
2 WASHER, Flat, .81 X .550 X 16GA
Position: 32
1 BOLT, Hex, 5/16-18 x 2-1/2
Position: 32
6 HAIRPIN
Position: 32
2 SCREW, 1/2-20 x 1-1/4" Hex Head Cap, GR5
Position: 32
1 WASHER, Flat 1.862 x .765 x 16GA
Position: 32
1 WASHER,Flat 1.862 x .765 x 16GA
Position: 32
1 SCREW, Thread Formning, 10-16 x
Position: 33
1 RING, Foam
Position: 33
4 BOLT, Hex-Head 5/16-18 x
Position: 33
3 WHEELS, Anti Scalp
Position: 33
2 NUT, 1/2-20 Hex
Position: 33
1 HAIRPIN
Position: 33
2 BOLT, Hex 3/8-16 x 1-1/2
Position: 34
4 NUT, Flange Lock 1/4-20
Position: 34
4 NUT, Hex Flange Lock, 5/16-18
Position: 34
3 SCREW, 3/8-24 x 3/4" Hex Head Cap, GR5
Position: 34
1 WASHER 25/32 x 1.5 x .132
Position: 34
1 THROTTLE CONTROL
Position: 35
1 GRIP, Seat Adjustment Lever
Position: 35
3 NUT, Flange Lock, 3/8-16
Position: 35
3 SPACER, 3" Long
Position: 35
1 SPRING, Extension PTO
Position: 35
2 WASHER, .39-1.14
Position: 35
2 SCREW, Self Tap, #8 x 3/8
Position: 36
1 HEAT SHIELD (Used with Service Kit 885280 or After Serial No. 2013421413)
Position: 36
2 WASHER, Flat, 3/4
Position: 36
3 NUT, Hex Nyloc, 3/8-24
Position: 36
4 BOLT, Carriage, 3/8-16 x 5/8
Position: 36
1 LATCH, Spring
Position: 36
1 TINNERMAN CLIP
Position: 37
3 WASHER, Flat 3/8
Position: 37
2 CAPSCREW, 5/16-18 x 3/4
Position: 37
1 FLOORMAT, RH
Position: 38
2 WASHER, Flat, 5/16
Position: 38
2 WASHER, .391 x 0.62 x.03
Position: 38
1 FLOORMAT, LH
Position: 39
4 WASHER, 0.641 x 1.38
Position: 39
1 BOLT, 1/4-20 x 1.0
Position: 39
1 HANDLE, Bagger
Position: 39
3 PIN, Cotter, 3/4
Position: 40
1 NUT, Keps Lock 1/4-20
Position: 40
2 SCREW, 1/4 - 20 x 5/8
Position: 40
1 RETAINER, Spring
Position: 41
5 HAIR PIN, .56D-.092T
Position: 41
1 BRACE
Position: 41
2 SCREW, Thread Forming, 10-24
Position: 42
1 BELT, Drive, 33"
Position: 42
2 CAPSCREW, Hex Hd., 3/8-16 x 1-1/4
Position: 42
1 SPRING, Extension
Position: 43
2 NUT, 3/8-16
Position: 43
1 Spring, Brake Extension
Position: 44
2 BOLT, Carriage 1/4-20 x 0.63
Position: 46
1 PAD, Hydro Pedal
Position: 47
1 ROD, Shift Link
Position: 48
1 LEVER, Lift Deck
Position: 49
1 GRIP, .50 Black
Position: 50
1 PIN, Front Hanger
Position: 51
4 NUT, Hex Flange 5/16-18
Position: 52
1 ROD, Roll Release
Position: 53
1 ROD, Battery
Position: 54
1 ROD, Clutch Hydro
Position: 55
1 SCREW, Self Tap 5/16-18 x 7/8
Position: 56
1 SPRING, Extension
Position: 57
2 SPACHER
Position: 58
6 WASHER, Flat, 1-1/4
Position: 59
1 PEDAL PAD, Hydro Reverse (BEFORE SERIAL NO. 2013421412)
Position: 60
1 PEDAL PAD, Hydro Reverse (AFTER SERIAL NO. 2013421413)
Position: 60
1 SERVICE KIT, Lifter Assembly (Not Illustrated, Includes Ref. Nos. 8 and 49)
Position: 61
LT75RD-CE
Position: 7800352
LT75RD-CE, FR
Position: 7800353
LT75RD-CE
Position: 7800356
LT75RD-CE, FR
Position: 7800357