Vue éclatée slt 100 Simplicity slt-100
Découvrez la vue éclatée complète slt 100 Simplicity slt-100, un guide indispensable pour identifier facilement toutes les pièces détachées de votre appareil. Que vous soyez à la recherche d'une pièce en particulier ou simplement pour vous aider à la réparation, notre présentation détaillée vous aide à comprendre chaque composant de votre slt 100. Optimisez la maintenance et la réparation de votre appareil grâce à des schémas précis et des références adaptées. Trouvez rapidement les pièces qu'il vous faut pour prolonger la durée de vie de votre slt 100 Simplicity slt-100 et éviter les pannes imprévues.
Assistant réparation
Powered by ChatGPT
Liste des pièces détachées
1 SWITCH ASSEMBLY, Ignition, 6-Pole (Includes Ref. Nos. 2, 3, 4 & 5)
Position : 1
1 SEAT, Hi Back, Steel Pan
Position : 1
1 ROD, Lift Handle
Position : 1
8 WASHER, 3/4
Position : 1
4 WASHER, Flat (Use on 22 Gross HP Models only)
Position : 1
1 VALVE, Shut Off Oil Drain
Position : 2
1 WASHER, 5/8
Position : 2
4 WASHER, Plain, 5/16
Position : 2
1 GRIP
Position : 2
2 WHEEL & TIRE ASSEMBLY, Front
Position : 2
1 SEAL, Short
Position : 3
1 SEAL, Long (Single)
Position : 3
1 LOCKWASHER, Internal Tooth, 5/8 (Not used on 2014 & newer models)
Position : 3
1 LATCH, Seat
Position : 3
1 CAPSCREW, Hex Head 5/16-18 x 1 G5
Position : 3
1 TIRE, Turf 15 X 6.00 - 6 Saver TL
Position : 3
1 NUT, Hex, Flange, 5/8-32
Position : 4
4 CAPSCREW, Hex Head Flange Dog Point, 5/16-18 x
Position : 4
1 WASHER, 5/16
Position : 4
1 TUBE, Tire, Front
Position : 4
4 CAPSCREW, Hex Washer Head Taptite 5/16-18 x 5/8
Position : 5
1 COVER, Ignition
Position : 5
4 SPACER, 0.32 ID x 1-1/2 OD
Position : 5
1 SPRING, Torsion
Position : 5
1 WHEEL & BUSHINGS ASSEMBLY, Front
Position : 5
1 IGNITION KEY (Set of 2)
Position : 6
1 SUPPORT, Seat
Position : 6
2 VALVE STEM & CAP
Position : 6
1 MUFFLER (Twin)
Position : 7
1 SWITCH, Headlights, 2 Terminal
Position : 7
2 BOLT, Carriage, 5/16-18 x 3/4
Position : 7
1 SPACER, Pivot Powdered Metal
Position : 7
4 BEARING
Position : 7
1 PLUG, Hole, Square
Position : 8
1 PIVOT, Seat
Position : 8
1 NUT, Hex Flange 5/16-18, Whiz Lock Small
Position : 8
1 FITTING, Grease, 1/4-28 Thread
Position : 8
1 PIPE, Exhaust R.H. (Twin)
Position : 9
1 PLUG, Hour Meter (Kohler and B&S Single)
Position : 9
4 BOLT, Carriage, 5/16-18 x 3/4
Position : 9
4 WASHER, Special Yellow
Position : 9
1 PIPE, Exhaust L.H. (Twin)
Position : 10
1 METER, Hour, LCD (B&S V-Twin Only)
Position : 10
4 NUT, Hex Flange, ESNA, 5/16-18
Position : 10
4 RING, Retaining
Position : 10
4 RING, Retaining (Use on 22 Gross HP Models only)
Position : 10
1 WASHER, Plain, 1/4 (6 Total for Export)
Position : 11
2 BOLT, Shoulder, 5/16-18 G5
Position : 11
4 CAP, Hub
Position : 11
4 CAP, Hub (Use on 22 Gross HP Models only)
Position : 11
1 MUFFLER (Single)
Position : 12
1 NUT, Hex, ESNA, 1/4-20
Position : 12
2 SPRING, Compression
Position : 12
2 KEY, 3/16 x 3/16 x
Position : 12
2 KEY, 3/16 x 3/16 x 2 (Use on 22 Gross HP Models only)
Position : 12
1 PIPE, Exhaust (Single)
Position : 13
1 BOLT, Carriage, 1/4-20 x 7/8
Position : 13
4 WASHER, Spring Black
Position : 13
2 WASHER
Position : 13
4 CAPSCREW, Hex Washer Head Taptite 1/4-20 x 1/2
Position : 14
1 NUT, Push On
Position : 14
2 COVER, Spring
Position : 14
2 CABLE, Lift w/Pin
Position : 14
2 CABLE, Lift w/Pin (Used on 46" & 52" Decks only)
Position : 14
2 SPACER, 3/4 ID x 1-1/4 OD x 1-5/8
Position : 14
1 CLIP, Speed Wire
Position : 15
1 HOLD DOWN, Battery
Position : 15
1 POD, LH Cup Holder
Position : 15
2 WHEEL & TIRE ASSEMBLY, Rear 20"
Position : 15
2 WHEEL & TIRE ASSEMBLY, Rear 20" (Use on 20 Gross HP Model only)
Position : 15
2 WHEEL & TIRE ASSEMBLY, Rear 22" (Use on Model 2690840)
Position : 15
1 CONTROL, Throttle Double (Single)
Position : 16
1 CONTROL, Throttle, Choke-A-Matic (Twin)
Position : 16
1 SWITCH, Push Button (NC)
Position : 16
1 ELBOW FITTING
Position : 16
1 ROD, Lift
Position : 16
1 TIRE, Turf 20 X 8.00 - 8 Saver TL
Position : 16
2 TIRE, 20 x 830-8, 2 Ply, K358 (Use 7101560)
Position : 16
2 TIRE, 22 x 10.00-8, 2 Ply, K358
Position : 16
2 CLAMP, Hose
Position : 17
3 TIE, Self Locking 7-5/16
Position : 17
1 BUSHING
Position : 17
1 TUBE, Tire, Rear (Use on 20" Tire)
Position : 17
2 TUBE, Tire, Rear (Use on 22" Tire)
Position : 17
1 HOSE, Fuel, Low Perm, 1/4ID x 1/2OD x 55.5 Lg
Position : 18
1 HOSE, Fuel, Low Perm, 1/4ID x 1/2OD x 49.5 Lg Use on engine model number 331777-
Position : 18
1 OUTLET, 12 Volt DC Power
Position : 18
1 TANK, Fuel
Position : 18
1 WHEEL, Hub
Position : 18
2 CLIP, Hose
Position : 19
1 PLUG, Hole Models W/O 12V Adapter
Position : 19
1 CAP, Gas
Position : 19
4 WASHER, Flat, 3/4 x 1-1/4 (Use on 22 Gross HP Models only)
Position : 19
3 CAPSCREW, Hex Washer Head Taptite 3/8-16 x 1 (Single)
Position : 20
1 SWITCH, Push Button (NO/NC) (18.5 Gross HP & 20 Gross HP Models)
Position : 20
1 SWITCH, Push Button (NO/NC) (22 Gross HP Models)
Position : 20
1 PAD, Footrest L.H.
Position : 20
1 LOCKWASHER, External Tooth 3/8
Position : 21
4 NUT, Hex, Flange Whizlock, 5/16-18
Position : 21
2/4 CLIP, Hair Pin
Position : 21
1 WASHER, 3/8
Position : 22
4 CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 5/8
Position : 22
1 PAD, Footrest R.H.
Position : 22
12 PIN, Clevis
Position : 22
1 HEADLIGHT ASSEMBLY (Includes Ref. Nos. 24, 25, 26 & 27)
Position : 23
1 PULLEY & HUB ASSEMBLY, Engine
Position : 24
2 SOCKET ASSEMBLY
Position : 24
6 CAPSCREW, Hex, Washer Head, Plastite, 1/4-20 x 1/2
Position : 24
1 QUADRANT, Lift
Position : 24
1 TIE, Self Locking
Position : 25
2 BULB, 1141-12V 21CP
Position : 25
2 CAPSCREW, Taptite, 5/16-18 x 5/8
Position : 25
1 DECAL, Mower Transport Lift
Position : 25
1 RETAINER, Clutch
Position : 26
1 REFLECTOR, Headlight
Position : 26
1 POD, RH Lift Quadrant
Position : 26
1 CARRIAGE BOLT, 1/4-20 x 5/8 G5
Position : 26
1 LENS, Headlight
Position : 27
1 GRIP, Lift
Position : 27
1 NUT, Hex Flange 1/4-20 Whiz Lock Large
Position : 27
1 CLUTCH, Electric OGURA (Used on Model Year 2008 and Prior)
Position : 28
1 CLUTCH, Electric OGURA (Used on Model Year 2009 and Later)
Position : 28
1 CLIP, Speed Wire (18.5 Gross HP & 20 Gross HP Models)
Position : 28
1 CLIP, Speed Wire (22 Gross HP Models)
Position : 28
1 WASHER, Hex
Position : 29
1 NUT, Hex, Flange, 1/4-20
Position : 29
1 LOCKWASHER, Spring
Position : 30
1 CAPSCREW, Hex Head 7/16-20 x 3-1/2 G5
Position : 31
1 HARNESS, Wiring (Use with Clutch 1731275SM)
Position : 31
1 HARNESS, Wiring (Use With Clutch 1736105SM) (Used on models with 12 Volt Adapter)
Position : 31
1 HARNESS, Wiring (Use With Clutch 1736105SM) (Used on models without 12 Volt
Position : 31
1/2 WASHER, 3/8
Position : 31
1 GASKET, Exhaust
Position : 32
1 CABLE, Solenoid to Starter
Position : 32
4/1 CAPSCREW, Hex Washer Head Taptite 3/8-16 x 1-1/4
Position : 33
1 SOLENOID
Position : 33
1/2 WASHER, 5/16
Position : 33
2 CAPSCREW, Hex Socket Head 5/16-18 x 3/4 G8
Position : 34
2 SCREW, Taptite, 1/4-20 x 1/2
Position : 34
2 LOCKWASHER, Spring 5/16
Position : 35
2 LOCKWASHER, External Tooth, 5/16
Position : 35
2 NUT, Hex, 5/16-24 NF
Position : 36
2 PIVOT, Hood
Position : 37
1 CABLE, #6 x 10 Long, with 2 Ring Terminals, Battery to Solenoid
Position : 37
2 BOLT, Carriage, 5/16-18 x
Position : 38
2 NUT, Hex, Flange Whizlock, 5/16-18
Position : 38
2 NUT, Hex Flange, 5/16-18
Position : 39
1 SUPPORT, RMO Switch
Position : 39
2 BOLT, Carriage, 5/16-18 x 3/4
Position : 40
1 BOOT, Insulator
Position : 41
1 BATTERY, 12 Volt, 230 CCA
Position : 42
1 SWITCH, Push Button (NO), Reverse Pedal
Position : 43
2 NUT, Hex, Full, 1/4-20
Position : 44
2 LOCKWASHER, 1/4
Position : 45
2 WASHER, 1/4 I.D.
Position : 46
1 CABLE, Battery to Ground
Position : 47
2 CAPSCREW, Hex Head, 1/4-20 x 3/4
Position : 48
1 FUSE, Wiring Harness
Position : 49
1 SWITCH, RMO Module Only
Position : 50
2 KEY, RMO Module, Plastic
Position : 51
1 SWITCH, PTO, Push/Pull Symbols
Position : 52
1 WIRING ASSEMBLY, All Conditions Shutdown (CE/Export)
Position : 53